• No results found

manual configuration of wireless network - eduroam windows 8 Click Open Network and Sharing Center.

N/A
N/A
Protected

Academic year: 2021

Share "manual configuration of wireless network - eduroam windows 8 Click Open Network and Sharing Center."

Copied!
8
0
0

Loading.... (view fulltext now)

Full text

(1)

eduroam windows 8

Eduroam is the preferred network for students and staff at Aarhus university. You can get easy and automatic access to the internet at aarhus university and at other universities in denmark or abroad with eduroam since it is an international collaboration with hundreds of universities participating worldwide. Visit www. eduroam.org to see the list of participating institutions.

You only need to set up eduroam once on your device. it automatically connects when it detects eduroam in the air. this also applies if you visit a foreign university where eduroam is also available. Hence the foreign university is not required to handle guest login or separate network access for guest students or teachers.

select ‘set up a new connection or a new network’ as shown in the picture.

nB! Before you begin following the guide, please make sure that your wireless network card is turned on. usually there is a small pin on the side of the computer that you can use to turn the wireless network card on or off. Please check the manufacturer’s manual if this causes problems.

go to your desktop and click the network icon in the lower right corner depicted as a row of white columns or transparent columns with a star on top.

(2)

the wireless network eduroam has now been added and the settings must be adjusted.

click ‘Change connection settings’.

click ‘manually connect to a wireless network’. then click ‘next’ at the bottom of the window.

In the field ‘network name’, type ‘eduroam’. Please make sure that ‘eduroam’ is entered correctly in lowercase letters.

Set the field ‘security type’ to ‘WPA2-Enterprise’. Leave the field ‘encryption type’ at ‘aes’.

make sure that the check box ‘start this connection automatically’ is checked.

(3)

the window ‘eduroam wireless network Properties’ will now appear.

click the ‘security’ tab.

under ‘Choose a network authentication method:’, select ‘Microsoft: EAP-TTLS’ from the drop-down menu.

click ‘settings’ to the right.

(4)

make sure that ‘Select a non-EAP method for authentication’ is set to ‘Unencrypted password (PAP)’.

click ‘oK’.

(5)

under ‘specify authentication mode’, select ‘user authentication’ from the drop-down menu.

then click ‘save credentials’ to the right.

You will now be asked to enter your username and your password. Fill in these fields as follows:

username: Your AU email address

Password: Your password from Self Service (mit.au.dk).

if you have questions regarding your username and password, you can find help online at eduroam.au.dk.

click ‘oK’.

You can now close the other windows by clicking ‘oK’ in the first two windows and ‘close’ in the last window.

(6)

click the network icon in the lower right corner of your desktop. the icon is either a row of white columns or a row of transparent columns with a star.

You will now see a list of available wireless networks.

click ‘eduroam’.

(7)

check the box ‘Connect automatically’ if it is not already checked.

now click ‘Connect’.

if you receive the message ‘Windows can’t verify the server’s

identity’, please click ‘Connect’ again.

You should now be connected to the eduroam network at aarhus university.

(8)

AdvAncEd MULTiMEdiA groUP

analytics group

tHis guide Has been Produced bY

advanced multimedia group is a division under au it supported by student assistants. our primary objective is to convey knowledge to relevant user groups through manuals, courses and workshops. our course activities are mainly focused on ms Office, Adobe CS and CMS. Furthermore we engage in e-learning activities and auditive and visual communication of lectures and classes. amg handles video assignments based on the recording, editing and distribution of lectures and we carry out a varied range of ad hoc assignments requested by employees.

In addition, AMG offers solutions regarding web development and we support students’ and employees’ daily use of typo3.

Analytics Group, a division comprised of student assistants under AU IT, primarily offers support to researchers and employees.

Our field of competence is varied and covers questionnaire surveys, analyses and processing of collected data etc. AG also offers teaching assistance in a number of analytical resources such as SAS, SPSS and Excel by hosting courses organised by our student assistants. These courses are often an integrated part of the students’ learning process regarding their specific academic area which ensures the coherence between these courses and the students’ actual educational requirements.

In this respect, AG represents the main support division in matters of analytical software.

Please address questions or comments regarding tHe contents of tHis guide to

bertel kirkebY

References

Related documents

Click Start > Control Panel > Network and Sharing Center > Network icon (icon with the network name you are connected to) and connect to computer 1.. Can you connect

1.3 In the Network and Sharing Center window, click on “Manage wireless networks”... 1.6 When prompted to enter the wireless

click the wireless icon. Open Network and Sharing Center. Set up a new connection or networkD. Manually connect to

Click the Start button in the bottom left corner of the Desktop > (Settings -- only if using the classic Windows start menu) > Network Connections > right-click on

From the Network and Sharing Center dialog window, click Manage Wireless Networks (Fig.. The Manually connect to wireless network dialog box

To configure your wireless connection, right click the wireless icon at the bottom right corner of your screen (near the clock) and select “Network and Sharing Center.” If you

In Windows Vista or 7, in the Network and Sharing Center, click Connect to a network.. A list of available network

Once Network and Sharing Center is open, you will want to click on Change Adapter Settings... Right click on Local Area Connection and left click