Ship Card
The Motorola MCC 7500 Dispatch Console is a high tier IP dispatch console for use with ASTRO 25 radio systems. It supports an evolving feature set which includes the following features.
Motorola MCC 7500 Dispatch Console
Dispatch Positions, Dispatch API and Product Software
--Features
System Level Features
Seamless IP Connectivity with Radio System Configured via Radio System Configuration Manager
Full Participation in Radio System Fault
Management Full Participation in Radio System Agency Partitioning
Compatible with MKM 7000 Console Alias Manager
Full Participation in Radio System Dynamic System Resilience (DSR)
ASTRO 25 Trunking Features
Full Access to ASTRO 25 Trunked Radio System IMBE/AMBE Vocoder for ASTRO 25 Resources
Full Support for Project 25 FDMA (Phase I) Operation
Full Support for Project 25 TDMA (Phase II) Operation
Trunked Talk Group Calls Trunked Announcement Group Calls
Trunked Private Calls Trunked Call Alerts
Trunked Emergency Alarms Trunked Emergency Calls
Trunked Tactical/Normal Trunked Repeater On/Off
Trunked Remote Monitor Trunked PTT ID and Alias
ASTRO 25 Conventional Features
PTT ID and Alias Call Alert
Emergency Alarm and Call Mixed Mode (Analog/Digital) Operation
Voice Selective Call Secure Call
Secure Key Select Secure Keyset Select
Received Key Display Autokey Key Display
Momentary Key Override Radio Enable/Disable
Radio Status Display Radio Status Request
Radio Message Display Radio Check
Remote Monitor Ignore Mobile to Mobile Calls
MDC 1200 Conventional Features
PTT ID and Alias Call Alert
Emergency Alarm Emergency Call
Voice Selective Call Radio Enable/Disable
Radio Status Display Radio Status Request
Radio Message Display Radio Check
Remote Monitor Ignore Mobile to Mobile Calls
Analog Conventional Features
Tone Remote Control E & M Control
Analog Talk & Listen Frequency Selection
Private Line (PL) Selection Repeater On/Off
Page 1 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Wild Card I & II Mute Second Receiver
Monitor Line Operated Busy Light (LOBL)
Supervisor Takeover (via Relay) Main/Alternate Conventional Interfaces
RF Cross Mute RF Cross Busy
General Secure Features
Supports up to 60 Encrypted Calls Simultaneously Supports up to 6 Encryption Algorithms Simultaneously
AES Algorithm DES-OFB Algorithm
DES-XL Algorithm ADP Algorithm
DVP-XL Algorithm DVI-XL Algorithm
Multi-Select Cross-Mode Alert Patch Cross-Mode Alert
Receive Cross-Mode Indication Clear Audio Alert
Key Management via KVL Key Management via Store and Forward (KMF with
KVL)
Key Management via OTEK (Over The Ethernet Keying)
General Console Features Intuitive, Easy-to-Use Graphical User Interfaces
(Elite or IED)
Elite GUI is Highly Configurable to meet Unique Customer Needs
Up to 8 Speakers Up to 2 Headsets
Desk Microphone Footswitch
Instant Recall Recorder Port for Radio Audio Instant Recall Recorder Port for Console Telephony Audio
Local Logging Recorder Port Telephone Headset Port (for radio & telephone on
one headset)
General Transmit Instant Transmit
Select/Unselect Multi-Select
15 Customizable Alert Tones (Trunking &
Conventional) Channel Marker (Trunking & Conventional)
VU Meter (On Screen) Integrated Tone Paging Encoder
Patch (Standard & Permanent) Generic Auxiliary Inputs & Outputs
ACIM Link to Consolette
Integrated Tone Paging Encoder Features
Manual Individual Pages Pre-Defined Individual Pages
Manual Group Pages Pre-Defined Group Pages
Sequential Paging Operation Simultaneous Paging Operation
Quick Page Buttons Talk Extend
PL Stripping "Selected Channel" Paging
Quick Call II B - Tone & Voice Quick Call II C - Tone Only
Quick Call II D - Battery Saver Quick Call II E - Competitive
Quick Call I Knox
Touch Code Motorola 5/6 Tone
Single Tone 0.5 Single Tone 1.5
Digital Dial 1 (1500 Hz) Digital Dial 2 (2805 Hz)
Digital Dial 3 (1500/2805) Trunked Call Alert
Page 2 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
VPM-Based Dispatch Consoles Items
The items which comprise a complete VPM-based dispatch console are available for purchase via the models, options and accessories described below. A combination of these items is required to create a complete VPM-based dispatch console as described in the following paragraphs.
Note: VPM-based dispatch consoles may not be ordered with 7.6 or earlier systems. VPM-based dispatch consoles may only be ordered for use with 7.7 or later systems.
Dispatch Console PC
A VPM-based dispatch console uses a dropship workstation PC together with a VPM. The dropship workstation PC comes with the Windows 7 operating system, keyboard and mouse. It does not include a monitor or Ethernet cable. These items must be ordered separately.
Each PC used with a dispatch console also requires the Symantec Anti-Virus application. Network Security Price Page
Note that the PC ships with a North American AC line cord. VPM and Licenses
When used with a MCC 7500 dispatch console, the VPM requires a MCC 7500 Basic Console Functionality Software
License (CA01642AA) and one of the AC line cord options (CA00140AA, AB, AC or AF).
The basic console functionality software license grants the customer the right to use the features supported by the dispatch console application software except for the features covered by the following licenses. Note that it also includes the right to use the API portion of the software.
Depending on the features desired on the dispatch console, one or more of the following license options may also have to be ordered with the VPM.
ADD: MCC 7500 Trunking Operation License (CA01643AA) - This option is required if the dispatch console will
be used to control ASTRO 25 trunking resources, SmartZone trunking resources (via a SmartX site converter) or SMARTNET trunking resources (via a SmartX site converter).
ASTRO 25 Conventional Call Alert MDC 1200 Call Alert
Enhanced Console Telephony Features
Supports POTS and/or E1/T1 Connections Answer/Initiate Calls from Console GUI
Dialing Keypad Configurable Ring Tones
Caller ID Call Hold
Call Forwarding Call Transfer
Speed Dials Phone Books
Patch Radio & Telephone Patch Go-Ahead Tones
VPM Features
Supports up to 8 Speakers Supports up to 2 Headsets
Supports one Desktop Microphone Supports one Footswitch
Telephone Headset Port (for radio & telephone on
one headset) Dedicated Private Auxiliary Inputs & Outputs
Instant Recall Recorder Port for Console
Telephony Audio Instant Recall Recorder Port for Radio Audio
Local Logging Recorder Port External Paging Encoder Port
Ethernet Connection between VPM and PC (up to
200 meters) Multiple Mounting Options
General Information
Page 3 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
ADD: MCC 7500 Advanced Conventional Operation License (CA01644AA) - This option is required if the
dispatch console will be used to control ASTRO 25 conventional channels, MDC 1200 channels and/or consolettes connected via ACIM Link.
ADD: MCC 7500 Inbound Event Display (IED) License (CA01645AA) - This option is required if the dispatch
console will use the Inbound Event Display (IED) graphical user interface.
ADD: MCC 7500 Enhanced Console Telephony Operation License (CA02073AA) - This option is required if the
dispatch console will use any of the enhanced console telephony features.
ADD: MCC 7500 Advanced SECURENET Operation License (CA01972AA) - This option is required if the
dispatch console will be used to control Advanced SECURENET channels.
The VPM does not include the following items. These must be ordered separately if required.
Speakers Desktop Microphone Headset Jacks Footswitch Ethernet Cable Secure Options
The VPM is capable of supporting up to 6 different encryption algorithms simultaneously. When secure operation is desired, order the ADD: MCC 7500 Secure Operation License option (CA00147AF) and from 1 to 6 encryption algorithm options (CA00143AC, CA00144AC, CA00145AC, CA00146AC, CA00182AB or CA00245AA).
A particular type of encryption algorithm may only be ordered once with a particular VPM. That is, up to 6 algorithms may be ordered with a VPM, but they must all be different algorithms.
If remote secure key management across the radio system's IP network from a KMF is desired, order the ADD: Over
The Ethernet Keying (OTEK) Operation License option (CA01220AA).
The TKN8531C cable is used to connect a KVL to a VPM for programming/managing secure key material. “The Peripherals”
The peripherals are the items which provide interfaces between the VPM and the external environment. These are:
Speaker (B1912) - Max of 8 per VPM
Desktop Microphone (B1914) - Max of 1 per VPM
Headset Jack (B1913) - Max of 2 per VPM
Footswitch (DSTWIN6328A) - Max of 1 per VPM
The speakers, microphone, headset jacks and footswitch are optional depending on the customer’s needs. Each MCC 7500 dispatch console requires 1 and only 1 VPM.
The VPM is 1 Rack Unit high and is capable of being mounted in a 19" rack. It may also be mounted beneath a writing surface or placed on top of a writing surface. Mounting hardware is included with the VPM.
Each VPM requires an AC line cord option (CA00140AA, AB, AC or AF).
Ordering information for the VPM is provided in the Models, Options and Accessories sections below. The price page for the rest of the peripherals may be found by clicking on this link: Peripheral Devices Price Page
Dual Instant Recall Recorder (IRR)
The dual IRR is compatible with VPM-based dispatch consoles. The dual IRR is capable of recording and playing back the audio from two different sources (e.g., radio and telephone), but may be used to record a single source if desired. If the IRR will be used to record the audio from only one source, the sound card does not need to be ordered. If the IRR will be used to record the audio from two sources, the sound card must be ordered. Only one set of PC speakers needs
Page 4 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
to be ordered regardless of whether the IRR is recording one or two sources of audio.
Please refer to the IRR Price Page for information about ordering IRRs for use with MCC 7500 consoles.
Dropship Items
The following dropship items are compatible with VPM-based dispatch consoles. The dropship items are accessories which are not manufactured by Motorola. These include:
Monitor Monitor Price Page
Trackball (See Accessories section below)
Ethernet Cable Ethernet Cable Price Page
Headset Peripheral Devices Price Page
Dual IRR IRR Price Page
Note: Headsets certified for use with the MCC 7500 dispatch console are only available from Motorola. While other headsets may work, Motorola cannot guarantee the quality of the audio, especially dispatcher transmit audio, if they are used.
Order the desired dropship items for each dispatch console. Use the links next to the items above to see the ECAT Pages for them. They may also be ordered for use as spares.
Software and Software Refresh Items
The software used on the dispatch console is available for purchase via the model and options shown below. The MCC
7500 ASTRO 25 Software (B1905) is a CD which contains the application software for both the dispatch console and
the archiving interface server. The two refresh license options (CA00899AA and CA00900AA) provide licenses for using new versions of the dispatch console or archiving interface server software.
These items may be used in the following scenarios. Buying a New Console System
The dispatch consoles and archiving interface servers come with the appropriate software installed on their computer hard disks, but they do not come with a copy of the software on CD or DVD. It is strongly suggested that at least one
MCC 7500 ASTRO 25 Software model (B1905) be ordered for each console system as a backup copy.
It is not necessary to order either of the software refresh license options when buying a new console system. They are used when upgrading an existing console system.
Upgrading an Existing MCC 7500 Console System
Upgrade an existing Motorola MCC 7500 console system to the latest version of software as follows.
Order the desired number of MCC 7500 ASTRO 25 Software models (B1905) (at least one is required, but more may be ordered if the customer wants them)
Order one ADD: Dispatch Console Software Refresh License option (CA00899AA) for each dispatch console being upgraded
Order one ADD: Archiving Interface Server Software Refresh License option (CA00900AA) for each archiving interface server being upgraded
The two software refresh license options provide licenses for using the new versions of the dispatch console or archiving interface server software. They must be ordered as sub-items to the MCC 7500 ASTRO 25 Software model. The quantities of the software refresh license options may (and most likely will) exceed the quantity of the main model. Note that the version of software used in the dispatch consoles and AISs must match the versions of software in all the other products in the radio system (zone controller, network manager, CCGWs, Aux I/O servers, etc.). It is usually not possible to upgrade just the dispatch consoles and AISs themselves.
Buying Additional Copies of the Software
Page 5 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
If a customer wishes to have additional copies of the dispatch console or archiving interface server software, then the
MCC 7500 ASTRO 25 Software model (B1905) may be ordered by itself.
Adding Operational Licenses to Fielded Dispatch Consoles and AISs
The following licenses are for use with fielded MCC 7500 dispatch consoles and archiving interface servers. The BLN1316 and BLN1317 are used only with customers who are either converting a SmartX Site Converter VPM into a MCC 7500 VPM or who are using FRUs to build a MCC 7500 dispatch console or archiving interface server. The rest of the licenses are used when adding the indicated functionality to a fielded dispatch console or archiving interface server, when converting a SmartX Site Converter VPM into a MCC 7500 VPM or when using FRUs to build a MCC 7500 dispatch console or archiving interface server.
Note that the CA01221AA and CA01221AB options are the equivalent of the BLN1316 + BLN1311 + BLN1312, so these do not need to be ordered if the CA01221AA or CA01221AB was ordered with the original dispatch console. Note also that the CA00288AA and CA00288AB options are the equivalent of the BLN1317, so it does not need to be ordered if the CA00288AA or CA00288AB was ordered with the original archiving interface server.
Adding Basic Dispatch Operation to a Dispatch Console being built from a Converted SmartX VPM or a VPM FRU Field-assembled VPM-based dispatch consoles can add the licensing for basic console operation by ordering the Basic
Console Operation Field-Add License (BLN1316) for each dispatch console being assembled in the field.
Adding AIS Software License to an AIS being built from a Converted SmartX VPM or a VPM FRU
assembled VPM-based archiving interface servers can add the AIS license by ordering the AIS Software
Field-Add License (BLN1317) for each archiving interface server being assembled in the field.
Adding Secure Operation
Existing dispatch consoles and archiving interface servers can add the licensing for secure operation by ordering the
Secure Operation Field-Add License (BLN1304) for each dispatch console and/or archiving interface server that needs
the feature. Note that this license does not provide any required hardware or encryption algorithms. They must be ordered separately.
Adding OTEK Operation
MCC 7500 dispatch consoles and archiving interface servers can support Over the Ethernet Keying (OTEK) operation beginning in the 7.7 system release. Existing systems that are 7.7 or later can add the licensing for OTEK operation by ordering the Over the Ethernet Keying (OTEK) Operation Field-Add License (BLN1302) for each dispatch console and/or archiving interface server that needs the feature.
Adding Trunking Operation
Existing dispatch consoles can add the licensing for trunking operation by ordering the MCC 7500 Trunking Operation
Field-Add License (BLN1311) for each dispatch console that needs the feature.
Adding Advanced Conventional Operation
Existing dispatch consoles can add the licensing for advanced conventional operation by ordering the MCC 7500
Advanced Conventional Operation Field-Add License (BLN1312) for each dispatch console that needs the feature.
Adding Inbound Event Display Operation
Existing dispatch consoles can add the licensing for IED operation by ordering the MCC 7500 Inbound Event Display
(IED) Operation Field-Add License (BLN1313) for each dispatch console that needs the feature.
Adding or Upgrading Encryption Algorithms on VPM-Based Dispatch Consoles
and AISs using a KVL 3000 Plus
If a customer wishes to add new encryption algorithms to existing secure-capable VPM-based MCC 7500 dispatch consoles and/or archiving interface servers using a KVL 3000 Plus KVL, the MCC 7500 VPM Secure Algorithm
Upgrade (T7583) should be ordered along with the desired algorithm options. This provides PCMCIA cards containing
the desired numbers and types of encryption algorithms. The PCMCIA card is then used in conjunction with a KVL 3000 Plus Key Variable Loader (KVL) to add the algorithms to secure cards.
The MCC 7500 VPM Secure Algorithm Upgrade may also be used to upgrade encryption algorithms to the latest versions in existing secure-capable VPM-based MCC 7500 dispatch consoles and/or archiving interface servers.
Page 6 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Order one algorithm option for each VPM that is being upgraded. For example, to add the ADP algorithm to three VPMs, order one T7583 with three CA00245AA options.
Multiple types of algorithm options may not be ordered on the same T7583. For example, to add the DES-OFB and AES algorithms to twenty-four VPMs, order two T7583s with twenty-four CA00143AC options on one and twenty-four CA00182AB options on the other.
The T7583 can support up to 100 copies of any single algorithm option.
When adding algorithms to a VPM on a 7.7 system, make sure the VPM has the 7.7 SER or later version of software (VPM_R7.7.00.23). Earlier versions of the 7.7 VPM software do not allow algorithms to be added in the field. Contact Upgrade Operations to obtain the 7.7 SER software. VPMs on 7.8 and later systems do not have any special software version requirements.
Adding or Upgrading Encryption Algorithms on VPM-Based Dispatch Consoles
and AISs using a KVL 4000
If a customer wishes to add new encryption algorithms to existing secure-capable VPM-based MCC 7500 dispatch consoles and/or archiving interface servers using a KVL 4000 KVL, the MCC 7500 VPM Secure Algorithm Upgrade for
KVL 4000 (T8063) should be ordered along with the desired algorithm options. This provides a CD containing the
desired numbers and types of encryption algorithms. The CD is then used in conjunction with a KVL 4000 Key Variable Loader (KVL) to add the algorithms to secure cards. The KVL 4000 keyloader must have at least the R02.05.03 (also listed as 1.3.0000.174) version of software to be able to load algorithms in VPMs.
Note: The serial number of the KVL 4000 keyloader must be entered into the ordering system when ordering the T8063. This serial number will be loaded on the CD by the factory. The CD can only be used by the keyloader with the matching serial number.
The MCC 7500 VPM Secure Algorithm Upgrade may also be used to upgrade encryption algorithms to the latest versions in existing secure-capable VPM-based MCC 7500 dispatch consoles and/or archiving interface servers. Order one algorithm option for each VPM that is being upgraded. For example, to add the ADP algorithm to three VPMs, order one T8063 with three CA00245AA options.
Multiple types of algorithm options may not be ordered on the same T8063. For example, to add the DES-OFB and AES algorithms to twenty-four VPMs, order two T8063s with twenty-four CA00143AC options on one and twenty-four CA00182AB options on the other.
The T8063 can support up to 100 copies of any single algorithm option.
When adding algorithms to a VPM on a 7.7 system, make sure the VPM has the 7.7 SER or later version of software (VPM_R7.7.00.23). Earlier versions of the 7.7 VPM software do not allow algorithms to be added in the field. Contact Upgrade Operations to obtain the 7.7 SER software. VPMs on 7.8 and later systems do not have any special software version requirements.
Adding or Upgrading Encryption Algorithms on non-VPM-Based Dispatch
Consoles and AISs
The MCC 7500 Secure Card Algorithm Upgrade (T7207) is a PCMCIA card which can be programmed with the desired encryption algorithm (CA00143AC, CA00145AC, CA00182AB or CA00245AA) for upgrading or adding a new algorithm to a customer's fielded GPIOM-based MCC 7500 dispatch console or voice/secure-card-based AIS. One encryption algorithm option is required per dispatch console and/or AIS being upgraded or added. Only one type of algorithm option may be ordered per T7207. If upgrading or adding multiple types of algorithms, then multiple T7207s must be ordered. This is illustrated in the following examples.
Example 1 - If 3 dispatch consoles and 1 AIS each have the AES and DES-OFB algorithms and it is desired to upgrade the AES algorithms, then 1 T7207 and 4 CA00182AB options are required. (Since the DES-OFB algorithm isn't being upgraded, no options are required for it.)
Page 7 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Example 2 - If 24 dispatch console and 3 AISs each need to have the ADP algorithm added to them, then 1 T7207 and 27 CA00245AA options are required. (It doesn't matter what algorithms are already in the dispatch consoles and AISs.) Example 3 - If 10 dispatch consoles need to have both the AES and the ADP algorithm added to them, then 1 T7207 with 10 CA00182AB (AES) options and 1 T7207 with 10 CA00245AA (ADP) options are required.
The desired number of encryption algorithm options are ordered as sub-items to the T7207
Note that if you are adding a B1924 Secure Card to the dispatch position, remember to order the following items for each card being installed. These items are available directly from the Radio Products and Services Division (RPSD, formerly AAD).
3085322Y01 - H.100 Cable (connects voice card and secure card together; one required per dispatch position) 0785669Y01 - Secure Card Support Bracket (used to support the secure card inside the PC; one required per secure card)
0310943J15 - Support Bracket Screws (used to fasten the support bracket to the PC chassis, two required per support bracket)
Dispatch API Software Development Kit
The Software Development Kit (SDK) for the MCC 7500 Dispatch API requires a license agreement to be executed between the software developer and Motorola Solutions. The license agreement, and instructions for completing it, can be found on the MCC 7500 wiki page. After the license agreement has been signed by both parties, an invoice will be issued for payment of the license fee ($250.00). After payment has been received, the SDK will be shipped to the developer. The B1925 is no longer used to order the SDK. Please note that the licensing process typically takes around 8 weeks to complete. Please plan accordingly.
The SDK is required when a customer wishes to use the MCC 7500 Dispatch API to allow 3rd party software to
communicate with the MCC 7500 dispatch console or if they wish to use a custom graphical user interface (GUI) on the dispatch console.
The right to use the Dispatch API is covered by the console software license (CA01221AA, CA01221AB, CA01222AA or CA01642AA) which must be purchased with each dispatch console, so no additional licenses are required.
Technical support for the SDK may be ordered using the QLN3437 Field Add MCC 7500 SDK Technical Support which provides one hour of technical support. Multiple quantities of the QLN3437 may be ordered if more than one hour of support is desired. The QLN3437 is a "billing only" item (a BB item) and therefore must be on a factory order by itself.
Note that if the QLN3437 is not ordered, no plant technical support will be provided for the software developers using the SDK.
Enhanced Console Telephony Media Gateways
IMPORTANT NOTICE! Orders for the media gateways described below currently cannot be fulfilled by Motorola Solutions. All orders containing either of these gateways will go on E3 hold while Supply Chain works to resolve this issue. But the resolution will only allow these media gateways to be sold within the USA; they will not be able to be sold in any other country. Customers in other countries who need these gateways will have to purchase them from Cisco or one of their authorized resellers. Please contact Eric Dahle ([email protected]) for information on what the customer will need to purchase.
Two versions of the media gateway are available.
The DDN1405 Media Gateway with 8 FXO Ports provides a media gateway with 8 analog POTS line ports. The gateway allows up to 50 dispatch positions to access the phone lines.
The DDN1404 Media Gateway with 2 E1/T1 Ports provides a media gateway with 2 E1/T1 ports. The gateway allows up to 100 dispatch positions to access the phone lines.
The E1/T1 version can support up to 60 phone calls when using the E1 ports and up to 48 phone calls when using the T1 ports.
Page 8 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Multiple media gateways can be used to increase the capacity if needed. Up to two media gateways can be located at a console site and up to 63 media gateways can be supported in a zone.
Field Replaceable Units (FRUs)
The following items are available directly from the Radio Products and Services Division (RPSD, formerly AAD). Note that some of these items cannot be ordered in COF and are indicated as such below. They must be ordered directly from RPSD.
3085322Y01 - H.100 Cable (connects voice card and secure card together; one required per dispatch position) 0785669Y01 - Secure Card Support Bracket (used to support the secure card inside the PC; one required per secure card)
0310943J15 - Support Bracket Screws (used to fasten the support bracket to the PC chassis, two required per support bracket)
3082534Y18 - VPM/GPIOM to Speaker Cable
3071113H01 - VPM/GPIOM to Headset Jack Permanent Cable 3071114H01 - VPM/GPIOM to Headset Jack Extension Cable 0183734Y01 - VPM/GPIOM to Microphone Cable
3085550Y02 - GPIOM to Voice Card Cable
01009513002 - VPM/GPIOM Power Supply (w/o DC cable or AC line cord, not orderable in COF)**
30009351001 - VPM/GPIOM DC Power Cable (connects 01009513001 power supply to VPM or GPIOM)** 3082933N08 - AC Line Cord (North American)
3082933N13 - AC Line Cord (UK)
3082933N09 - AC Line Cord (Continental European) 3508800G96 - Microphone Wind Screen
60009256001 - Secure Key Retention Battery (for VPM, not orderable in COF) The following are FRUs for the enhanced console telephony media gateways 01009704002 - Fan module for 2911
01009704003 - AC Power Supply 01009704004 - Fan module for 2921
01009704005 - 2-Port 3rd Gen Multiflex Trunk Voice/WAN Card – T1/E1 01009704006 - VIC2-4FXO Four-Port Voice Interface
01009704007 - 16-channel High-density voice and video DSP module 01009704008 - 512MB DRAM module
01009704009 - 2921/2951 AC Power Supply 01009704010 - 256MB Compact Flash
** Note that the 0183650Y03 GPIOM/VPM Power Supply has been replaced with a Level V energy efficiency compliant model. The original power supply has a non-detachable DC power cable, but the new supply has a detachable DC power cable. Please order both the 01009513002 Power Supply and 30009351001 DC Power Cable when replacing a 0183650Y03.
The various board-level FRUs for the MCC 7500 dispatch console are orderable via the accessory numbers shown below.
Manuals
The various manuals for the MCC 7500 dispatch console are included in the ASTRO 25 Radio System Documentation Set. The individual manuals (or the complete documentation set) can be downloaded from the ASTRO 25
Documentation Web Site.
MCC 7500 Product Planner and Ordering Guide
The MCC 7500 Product Planner and Ordering Guide is available on the MCC 7500 wiki page.
Ordering Requirements
Page 9 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Supported Ordering Systems
1. This equipment is ordered directly in COF or OMAR. Note that no checking of the design itself is done in COF or OMAR.
2. Motorola On-Line may not be used to order complete console systems.
Don't Forget These Items for Each Dispatch Console
1. VPM, Speaker, Microphone, Headset Jack 2. AC Line Cords
3. Monitor
4. Software License
Links to Other Elements of the Console Sub-System
1. Conventional Channel Gateway Items 2. Auxiliary Input/Output Items
3. Archiving Interface Server (AIS) Items 4. Logging Recorder Items
5. Dispatch Furniture Info 6. Manuals
Dispatch Console PC
NOTE: The HP Z420 computer does not support the Windows Vista or XP operating systems. If you need to order a computer with one of those operating systems, please refer to the Servers, Workstations, OS and Ancillary ItemsECAT page.
VPM
Software Items
Note: The B1925 is no longer used to order the SDK for the MCC 7500 Dispatch API. Please see the "Dispatch API Software Development Kit" section above for information on how to obtain the SDK.
Models
Description Nomenclature APC Price
Z420 LOW TIER WORKSTATION WINDOWS 7 TT2538 708 $2,550.00
Provides a HP Z420 computer with the Windows 7 (64 bit) operating system, a keyboard and a mouse. Does not include a monitor or any application software. Not compatible with GPIOM based MCC 7500 consoles (it doesn't have enough PCI slots and doesn't support Vista or XP O/Ss).Does not support Hardware Encrypt Key Mgmt on MCC 7100.
MOTOROLA VOICE PROCESSOR MODULE B1933 443 $11,920.00
Provides one Voice Processor Module (VPM) unit for an MCC 7500 console. Requires appropriate software license option (CA01642AA or CA00288AB) and AC line cord option (CA00140AA, AB, AC or AF).
When ordered for a secure-capable MCC 7500 console, also requires the CA0147AF Secure Operation License option and at least one encryption algorithm.
Description Nomenclature APC Price
MCC 7500 ASTRO 25 SOFTWARE B1905 443 $250.00
Provides a CD ROM containing the application software for the MCC 7500 dispatch console and MCC 7500 Archiving Interface Server. Does NOT include the licenses required to use the software. Licenses can be purchased by using
- CA01642AAB or CA00288AB with the B1933
Page 10 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Software License
Upgrade Software Licenses
Trunking & Advanced Conventional Operation
Advanced SECURENET Operation
Secure Operation
Secure Algorithms
Options
Description Nomenclature APC Price
ADD: MCC 7500 BASIC CONSOLE FUNCTIONALITY SOFTWARE LICENSE
CA01642AA 443 $12,000.00
Provides a license for using the MCC 7500 Dispatch Console Software. A software license is required for each dispatch position being ordered. Covers basic console features such as non-signaling analog conventional, patch, multi-select, paging, aux i/os, alert tones, channel marker, using the API, etc. Order as a sub-item to the B1933.
ADD: MCC 7500 DISPATCH CONSOLE SOFTWARE REFRESH LICENSE
CA00899AA 443 $3,000.00
Provides a license for upgrading to the latest version of the MCC 7500 Dispatch Console Software. One is required for each dispatch console being upgraded. Order as a sub-item to the B1905.
ADD: MCC 7500 AIS SOFTWARE REFRESH LICENSE CA00900AA 443 $2,700.00
Provides a license for upgrading to the latest version of the MCC 7500 AIS Software. One is required for each AIS being upgraded. Order as a sub-item to the B1905.
ADD: MCC 7500 / MCC 7100 TRUNKING OPERATION CA01643AA 443 $5,000.00
Required when the MCC 7500 or MCC 7100 dispatch position is used to control trunking resources (ASTRO 25, SmartZone via SmartX or SMARTNET via SmartX). Order as a sub-item to the B1933 for MCC 7500 and as a sub-sub-item to B1939 for MCC 7100.
ADD: MCC 7500 /MCC 7100 ADV CONVL OPERATION CA01644AA 443 $3,000.00
Required when the MCC 7500 or MCC 7100 dispatch position is used to control ASTRO 25 conventional channels, MDC 1200 channels or ACIM Link channels. Order as a sub-item to the B1933 for MCC 7500 and as a sub-item to the B1939 for MCC 7100.
ADD: ADVANCED SECURENET OPERATION CA01972AA 443 $50,000.00
Required when the MCC 7500 dispatch position is used to control Advanced SECURENET resources (Conventional channels using an Advanced SECURENET CIU device). Order as a sub-item to the B1933.
ADD: MCC 7500 SECURE OPERATION CA00147AF 443 $3,250.00
Order when secure capabilities are required in a VPM-based dispatch console or AIS. Order as a sub-item to the B1933.
ADD: MCC 7500 / MCC 7100 OTEK OPERATION CA01220AA 443 $3,350.00
Order when remote key management capabilities are required on a VPM-based dispatch console or AIS or when a CRYPTR micro SD Card is used with MCC 7100. Order as a sub-item to the B1933 for MCC 7500 and as a sub-sub-item to the B1939 for MCC 7100. Note that OTEK does not support the ADP encryption algorithm.
ADD: DES-OFB ALGORITHM CA00143AC 443 $750.00
Provides factory programming for the DES-OFB encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server, VPM FRU or Secure Card FRU model.
ADD: DES-XL ALGORITHM CA00144AC 443 $750.00
Provides factory programming for the DES-XL encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server or VPM FRU.
Page 11 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Inbound Event Display GUI
Enhanced Console Telephony
Power Cords
API Technical Support
Enhanced Console Telephony Media Gateways
NOTE: Motorola Solutions is temporarily unable to fulfill orders for the DDN1404 and DDN1405. At this time there is no firm date for how long this will last. Orders containing the DDN1404 or DDN1405 will go on E3 hold until they can be fulfilled. Please see the note in the General Information section above.
ADD: DVI-XL ALGORITHM CA00145AC 443 $750.00
Provides factory programming for the DVI-XL encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server, VPM FRU or Secure Card FRU model.
ADD: DVP-XL ALGORITHM CA00146AC 443 $750.00
Provides factory programming for the DVP-XL encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server or VPM FRU model.
ADD: AES ALGORITHM CA00182AB 443 $750.00
Provides factory programming for the AES encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server, VPM FRU or Secure Card FRU model.
ADD: ADP ALGORITHM CA00245AA 443 $300.00
Provides factory programming for the ADP encryption algorithm. Order as a sub-item to the appropriate MGEG, MCC 7500 Dispatch Console, MCC 7500 Archiving Interface Server, VPM FRU or Secure Card FRU model.
ADD: MCC 7500/MCC 7100 IED OPERATION CA01645AA 443 $4,200.00
Required when the MCC 7500 or MCC 7100 dispatch position uses the Inbound Event Display GUI. Order as a sub-item to the B1933 for MCC 7500 and as a sub-item to the B1939 for MCC 7100
ADD: MCC 7500 Enhanced Console Telephony Operation License CA02073AA 443 $1,200.00
Required when the MCC 7500 dispatch position is used to control enhanced console telephony phone lines. Order as a sub-item to the B1933.
ADD: AC LINE CORD, NORTH AMERICAN CA00140AA 443 $0.00
Adds one AC line cord with a North American plug.
ADD: AC LINE CORD, EUROPEAN CA00140AB 443 $0.00
Adds one AC line cord with a continental European plug (Schuko plug).
ADD: AC LINE CORD, UK CA00140AC 443 $0.00
Adds one AC line cord with a United Kingdom plug.
ADD: AC LINE CORD, AUSTRALIA CA00140AF 277 $0.00
Adds one AC line cord with an Australian plug.
FIELD ADD MCC 7500 SDK TECHNICAL SUPPORT QLN3437 404 $1,000.00
Provides one hour of technical support for the SDK from the factory. May be ordered multiple times if more than one hour of support is required. May be ordered to add additional technical support for software developers who are already using the SDK. Note that this is a billable item only (BB item) and must be ordered by itself on its own order.
Accessories
Page 12 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Field-Add Software Licenses
Trackball
Programming Cables
Field Replacement Units
Note: We've been seeing a significant number of VPM FRUs being returned to the Repair Depot because they don't
Description Nomenclature APC Price
QUOTE 118635552-3 FOR CISCO MEDIA GATEWAY WITH 2 T1 E1 PORTS
DDN1404 443 $14,090.00
Provides a Cisco 2921 IP PBX with two E1/T1 ports and licensing for up to 100 dispatchers to access it.
QUOTE 118635859-3 FOR CISCO MEDIA GATEWAY WITH 8 POTS LINES
DDN1405 443 $9,390.00
Provides a Cisco 2911 IP PBX with 8 analog POTS line ports and licensing for up to 50 dispatcher to access it.
MCC 7500 Console Telephony Media Gateway O/S for Upgrade or Recovery
BVN1014A 877 $500.00
Provides a CD-ROM containing a copy of the operating system for the enhanced console telephony media gateways. This should be ordered for use in upgrade or disaster recovery scenarios.
OVER THE ETHERNET KEYING (OTEK) OPERATION FIELD-ADD LICENSE
BLN1302 443 $3,350.00
SECURE OPERATION FIELD-ADD LICENSE BLN1304 443 $3,250.00
MCC 7500 / MCC 7100 TRUNKING OPERATION FIELD-ADD LICENSE
BLN1311 443 $5,000.00
MCC 7500 / MCC 7100 ADVANCED CONVENTIONAL OPERATION FIELD-ADD LICENSE
BLN1312 443 $3,000.00
MCC 7500 / MCC 7100 INBOUND EVENT DISPLAY (IED) FIELD-ADD LIC
BLN1313 443 $4,200.00
MCC 7500 BASIC CONSOLE FUNCTIONALITY FIELD-ADD LICENSE
BLN1316 443 $12,000.00
MCC 7500 AIS SOFTWARE FIELD-ADD LICENSE BLN1317 443 $15,060.00
MCC 7500 Enhanced Console Telephony Operation Field-Add License BLN1320A 443 $1,200.00
TRACKERBALL (ONLY PS/2 & USB COMPATIBLE) DSCDN6171B 708 $439.00
Trackball is "ruggedized" and "RF-CERTIFIED" by Consoles Engineering. Order as a main line item.
MOBILE KEYLOAD CABLE (RNC DUI MGEG) TKN8531C 201 $84.00
Keyloading cable for APX 7500, XTL 5000, XTL 2500, and ASTRO Spectra. Correct keyloading cable adaptor must be ordered seperately:
-HKN6182 for APX 7500, XTL 5000 (O series control head), and XTL 2500. -TRN7414 for XTL 5000 (W series control head) and ASTRO Spectra.
PCI SECURE CARD FRU, MCC7500 CONSOLE B1924 443 $5,500.00
Provides one secure card for use in a secure-card-based MCC 7500 Dispatch Console or a secure-card-based MCC 7500 Archiving Interface Server. Requires from 1 to 4 algorithm options. Order as a main line item.
FRU VOICE CARD BLN1263 443 $5,000.00
Provides one voice card for use in a voice-card-based MCC 7500 Dispatch Console or a voice-card-based MCC 7500 Archiving Interface Server. Order as a main line item.
GPIOM HOUSING & CIRCUIT BOARD FRU BLN1274 443 $3,325.00
Provides the housing and circuit board used for the B1911 GPIOM. Does not include the power supply or IEEE 1394 cable. Order as a main line item.
Page 13 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
have the necessary encryption algorithms. Please read the note text under the B1934 below and make sure any required encryption algorithms are ordered when the VPM FRU is ordered.
Algorithm Upgrades/Field-Adds
Data Compiled 02-Feb-2015 using DUP and all prices in USD
MCC 7500 VOICE PROCESSOR MODULE FRU B1934 443 $11,830.00
Provides the housing and circuit board used for the B1933 VPM. Does not include the power supply, AC power cord, or DC power cord. Each of these items must be ordered separately from RPSD. If secure capability is required, then order the following options with the B1934:
- the secure operation option (CA00147AF) - from 1-6 encryption algorithm options Order as a main line item.
DESKTOP SPEAKER CIRCUIT BOARD FRU BLN1275 443 $180.00
Provides the circuit board used in the B1912 speaker. Does not include housing, speaker cone or cables. Order as a main line item.
DESKTOP MIC CIRCUIT BOARD FRU BLN1276 443 $38.00
Provides the circuit board used in the B1914 microphone. Does not include housing, switches, gooseneck shaft, microphone cartridge or cables. Order as a main line item.
HEADSET JACK CIRCUIT BOARD FRU BLN1277 443 $114.00
Provides the circuit board used in the B1913 headset jack. Does not include housing, PJ7 connectors or cables. Order as a main line item.
SHIELD,VPM SHIELD KIT BLN1324 443 $0.00
Provides one complete shield kit to replace the encryption engine shields on a Voice Processor Unit (VPM). Instructions for replacing the shields are also provided. When ordering, divide the quantity needed into multiple lines so that no line contains more than 9 BLN1324's. For example, if 30 kits are needed, create 3 lines of 9 each and 1 line of 3.
Z420 LOW TIER WORKSTATION WINDOWS 7 TT2538 708 $2,550.00
Provides a HP Z420 computer with the Windows 7 (64 bit) operating system, a keyboard and a mouse. Does not include a monitor or any application software. Not compatible with GPIOM based MCC 7500 consoles (it doesn't have enough PCI slots and doesn't support Vista or XP O/Ss).Does not support Hardware Encrypt Key Mgmt on MCC 7100.
MCC 7500 SECURE CARD ALGORITHM UPGRADE T7207 404 $125.00
Provides a PCMCIA card that is used to add new algorithms to existing GPIOM-based MCC 7500 consoles or voice/secure-card-based AISs. Also used to upgrade existing algorithms in existing MCC 7500 consoles or AISs. Requires sufficient algorithm options to cover every added/upgraded algorithm in every console or AIS that is affected. Order as a main line item.
MCC 7500 VPM SECURE ALGORITHM UPGRADE T7583 443 $125.00
Provides a PCMCIA card that is used to add new algorithms to existing Telephone Media Gateways (TMGs), VPM-based MCC 7500 consoles and VPM-based AISs. Also used to upgrade existing algorithms in existing VPM-based MCC 7500 consoles or AISs. Requires sufficient algorithm options to cover every added/upgraded algorithm in every console or AIS that is affected. The PCMCIA card is only compatible with the KVL 3000 Plus Key Variable Loader. Order as a main line item.
MCC 7500 SECURE VPM ALGORITHM UPGRADE FOR KVL 4000 T8063 443 $250.00
Provides a CD that is used to add new algorithms to existing Telephone Media Gateways (TMGs), VPM-based MCC 7500 consoles and VPM-based AISs. Also used to upgrade existing algorithms in existing VPM-based MCC 7500 consoles or AISs. Requires sufficient algorithm options to cover every added/upgraded algorithm in every console or AIS that is affected. The CD is only compatible with the KVL 4000 Key Variable Loader. The serial number of the KVL 4000 keyloader is required to be entered into the ordering system when ordering the T8063. Order as a main line item.
Page 14 of 14
Motorola MCC 7500 Products \ MCC 7500 Dispatch Consoles
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/AST7500...
Ship Card
The Motorola MCC 5500 and MCC 7500 Dispatch Consoles use the peripheral devices described on this page. To access the ECAT pages for either of these dispatch consoles, please use the following links.
Motorola MCC 5500 Dispatch Console
Motorola MCC 7500 Dispatch Console
The items described on this page are known as "peripheral devices" and are used with the Motorola MCC 5500 and 7500 dispatch consoles.
Desktop Speaker (B1912)
The desktop speaker is a self-contained, amplified speaker with a continuous volume knob. It can be configured to either completely mute or maintain a minimum volume level when the volume knob is turned all the way down. It may be attached to a vertical or horizontal surface, or may be left freestanding. It is compatible for use near CRT monitors. Each MCC 5500 dispatch console can support up to 8 desktop speakers.
Each MCC 7500 dispatch console can support up to 4 desktop speakers.
Motorola MCC 5500 and MCC 7500 Dispatch Console Peripheral Devices
-- Speaker, Microphone, Headset Jack, Headsets and Footswitches --
Features
Desktop Speaker Features
2 Watt Output Continuously Adjustable Volume Knob
Optional Minimum Output Level Compatible for use near CRT Monitors
Desktop or Wall Mounting 10 Foot Cable
Desktop Microphone Features
18" Flexible Gooseneck Weighted Base for Stability
Push-To-Talk (PTT) Button Monitor Button
Windscreen Cover on Mic Cartridge Ergonomic Design
May be Attached to Desktop or Left Freestanding 10 Foot Cable
Headset Jack Features
Continuously Adjustable Volume Knob for Radio Continuously Adjustable Volume Knob for Telephone
May be mounted up to 12 Cable-Feet Away Flexible Mounting Capabilities
Supports 4-Wire and 6-Wire Headsets Configurable Sidetone Operation
Headset Features
Separate Amplifier and Top Sections Mix and Match Amplifier and Top Sections
Monaural and Binaural Earpieces Earmuff and Earbud Style Earpieces
Standard Microphone Noise Canceling Microphone
Built-In PTT Switch 15 and 25 Foot Cord Lengths
6 Wire PJ7 Longframe Connector 4 Wire PJ327 Longframe Connector
Footswitch Features
General Transmit Pedal Monitor Pedal
Rugged, Proven Design
General Information
Page 1 of 4
Motorola MCC 7500 Products \ MCC Series Accessories
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/MCCACC...
Desktop Microphone (B1914)
The desktop microphone is a self-contained microphone with an 18" flexible gooseneck shaft. It contains a transmit button and a monitor button for use with the selected radio channel(s). It may be attached to a horizontal surface or may be left freestanding.
Each MCC 5500 and MCC 7500 dispatch console can support 1 desktop microphone.
Headset Jack (B1913)
The headset jack allows headsets to be used with a dispach console. It contains two continuous volume controls, one for radio audio and one for telephone audio. It is capable of supporting either 6-wire (i.e., with a PTT switch) or 4-wire (i.e., without a PTT switch) headsets. It may be mounted beneath or on top of a writing surface.
Each MCC 5500 and MCC 7500 dispatch console can support up to 2 headset jacks.
Headsets
The headset plugs into the headset jack and allows the dispatcher to listen to receive audio on the selected radio channels and to talk on any radio channels. If the dispatch console is configured to do so, the dispatcher can also talk and listen to telephone resources using the headset.
The headset comes in two sections, a top and a bottom. The top consists of an earpiece, a microphone, a cable for connecting to the bottom section and a clip for attaching the cable to the user's clothing. The bottom consists of an amplifier unit with volume control, an optional PTT switch, a connector for connecting to the headset jack, a clip for attaching the amplifier to the user's clothing and either a 15 or 25 foot cable for connecting to the jack. Both a top and a bottom are required to create a functional headset.
The RMN5077B, RMN5078B, RMN5079B and RMN5080B tops used with the RLN6098 or RLN6099 bases are the only headsets certified for use with the MCC 7500 dispatch console. These have been tested to ensure they provide a high level of audio quality and performance when used with the APCO Project 25 IMBE and AMBE vocoders. While other headsets will work with the MCC 7500 dispatch console, using them may result in degradation of audio quality, especially on console transmit audio.
The following table shows a cross reference between the Motorola part numbers and the Plantronics part numbers for the headsets listed on this page.
Any of the headsets listed on this page may be used with the MCC 5500 dispatch console.
Footswitch (BLN6732)
The BLN6732 footswitch is used only with the MCC 5500 dispatch console. It provides two foot pedals in a rugged, metal housing with a 7 foot cable. One pedal is used for the general transmit feature while the other pedal is used for the monitor feature.
Each MCC 5500 dispatch console can support 1 footswitch.
Motorola P/N Plantronics Model Plantronics P/N
RMN5077B HW251 64336-31 RMN5078B HW251N 64338-31 RMN5079B HW261 64337-31 RMN5080B HW261N 64339-31 RLN6098A SHS1890-15/DH 72949-15 RLN6099A SHS1890-25/DH 72949-25
Page 2 of 4
Motorola MCC 7500 Products \ MCC Series Accessories
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/MCCACC...
Footswitch (DSTWIN6328A)
The DSTWIN6328A footswitch is used only with the MCC 7500 dispatch console. It provides two foot pedals in a rugged, metal housing with a 10 foot cable. One pedal is used for the general transmit feature while the other pedal is used for the monitor feature.
Each MCC 7500 dispatch console can support 1 footswitch.
Supported Ordering Systems
1. MCC 7500 console equipment is ordered directly in COF. Note that no checking of the console design itself is done in COF.
Don't Forget These Items
1. Don't forget to order the headsets. They are not included with the headset jacks. 2. Don't forget to order both a top and a bottom for each headset.
To access the ECAT pages for the MCC 5500 or MCC 7500 dispatch consoles, please use the following links.
Motorola MCC 5500 Dispatch Console Motorola MCC 7500 Dispatch Console
Headset Bottoms
Headset Tops
Footswitches
Ordering Requirements
Models
Description Nomenclature APC Price
MCC SERIES DESKTOP SPEAKER B1912 443 $450.00
Provides one desktop style speaker. Includes speaker with master volume control, 10 foot cable and mounting hardware. Compatible for use near CRT monitors.
MCC SERIES HEADSET JACK B1913 443 $200.00
Provides one headset jack. Includes separate volume controls for radio and telephone audio, a 6 foot permanently attached cable and a 6 foot extension cable. Ships from the factory configured for use with 6-wire headsets. Can be field-modified to work with 4-wire headsets.
MCC SERIES DESKTOP GOOSENECK MICROPHONE B1914 443 $250.00
Provides one desktop style microphone. Includes transmit and monitor buttons, an 18" gooseneck shaft and a 10 foot cable. Compatible for use near CRT monitors.
Accessories
HDST MODULE BASE W/PTT, 15' CBL RLN6098 706 $210.00
HDST MODULE BASE W/PTT, 25' CBL RLN6099A 706 $242.00
SUPRAPLUS SINGLE MUFF HEADSET RMN5077B 706 $110.00
SUPRAPLUS NC SINGLE MUFF HEADSET RMN5078B 706 $149.00
SUPRAPLUS DUAL MUFF HEADSET RMN5079B 706 $117.00
SUPRAPLUS NC DUAL MUFF HEADSET RMN5080B 706 $139.00
FOOT, SWITCH TRADITIONAL BLN6732 454 $120.00
Page 3 of 4
Motorola MCC 7500 Products \ MCC Series Accessories
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/MCCACC...
Field Replacement Units
Data Compiled 02-Feb-2015 using DUP and all prices in USD
PROVIDES ONE DUAL PEDAL FOOTSWITCH FOR USE WITH MOTOROLA MCC 7500 DISP
DSTWIN6328A 708 $290.00
Dual pedal footswitch for use with the Motorola MCC 7500 dispatch console. Similar to the BLN6732 except it has a RJ45 connector.
DESKTOP SPEAKER CIRCUIT BOARD FRU BLN1275 443 $180.00
Provides the circuit board used in the B1912 speaker. Does not include housing, speaker cone or cables. Order as a main line item.
DESKTOP MIC CIRCUIT BOARD FRU BLN1276 443 $38.00
Provides the circuit board used in the B1914 microphone. Does not include housing, switches, gooseneck shaft, microphone cartridge or cables. Order as a main line item.
HEADSET JACK CIRCUIT BOARD FRU BLN1277 443 $114.00
Provides the circuit board used in the B1913 headset jack. Does not include housing, PJ7 connectors or cables. Order as a main line item.
Page 4 of 4
Motorola MCC 7500 Products \ MCC Series Accessories
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/MCCACC...
Ship Card
The Motorola MCC 7500 Dispatch Console is a high tier IP dispatch console for use with ASTRO 25 radio systems. It supports an evolving feature set which includes the following features.
Overview
Auxiliary inputs and outputs (Aux I/Os) allow customers to control external devices via relay closures and sense the state of external devices via input buffers from the dispatch position. The Motorola MCC 7500 and MCC 7100 consoles support Aux I/Os by accessing and controlling SDM 3000 Basic RTUs and displaying the status of the RTUs’ inputs and outputs on the dispatch position graphical user interface (GUI). The graphical user interface displays the inputs and outputs by using the same icons that are used with inputs and outputs on CENTRACOM Gold Series dispatch positions. A separate GUI to display the RTU inputs and outputs is not required on the dispatch position.
Multiple dispatch positions may monitor and control the same relay output and/or external inputs. In this case, state changes are indicated across all dispatch positions simultaneously.
Individual relay outputs can be configured so that they require a safety switch to be pressed before they respond to any commands from the dispatcher. A relay output on one dispatch position can be protected by a safety switch while the same relay output on a different dispatch position isn’t. The resetting of latched inputs may also be protected by using the safety switch.
Supported Aux I/O Types
The following Aux I/O configurations are supported.
Momentary Input - This is an input where the user interface always shows the true state of the input. If the input
is active, it is shown as active. If it is not active, it is shown as not active.
Latched Input - This is an input where the user interface doesn’t necessarily show the true state of the input.
When the input goes active, the user interface shows the state as active. The display will continue to show the state as active even if the input changes to the inactive state. A dispatcher must manually reset the display to return it to the inactive state. Note that a dispatcher cannot clear the display until the input itself is in the inactive state.
Momentary Output - This is an output relay which is activated when the dispatcher presses the button on the
user interface and deactivated when the dispatcher releases the button.
Latched Output - This is an output relay which changes state only when the dispatcher presses the button. The
release of the button has no effect on the state of the relay. One press activates the relay; the next press deactivates the relay.
Interlocked Latched Output - This is a latched output relay which is part of a group of latched output relays.
Only one of the relays in the group may be active at a time. Pressing the button for a relay automatically deactivates the previously active relay. Pressing the same button twice does not deactivate that relay. There is always one and only one relay active in the group at all times. Interlocked relays work in a “break before make” fashion; that is, the previously active relay is deactivated before the new relay is activated. The maximum
number of relays that can be grouped together in an interlocked group is the number of relays in the RTU hosting
Motorola MCC 7500 Dispatch Console
-- Auxiliary Input/Output Items --
Features
Aux I/O Types
Latched Relay Outputs Momentary Relay Outputs
Latched Input Buffers Momentary Input Buffers
Interlocked Relay Groups Channel-Associated Aux I/Os
General Information
Page 1 of 4
Motorola MCC 7500 Products \ MCC 7500 Aux I/O Items
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/CC2CON...
the interlocked group. SDM 3000 Basic RTUs
The F4543 SDM3000 Basic RTU is used to support most console Aux I/O needs. The RTU is rack mountable in a standard 19 inch rack and is one rack unit high.
The RTU is capable of supporting up to 16 outputs and 48 inputs. Expansion chassis (each being the same physical size as the SDM3000 RTU) can be added to increase the number of inputs and outputs. The supported configurations are as follows.
A single SDM 3000 Basic RTU supports 16 Relay Outputs and 48 Input Buffers
A single SDM 3000 Basic RTU with 1 expansion chassis supports 32 Relay Outputs and 96 Input Buffers
A single SDM 3000 Basic RTU with 2 expansion chassis supports 48 Relay Outputs and 144 Input Buffers Two options are available for powering the RTU. One of the following power options must be ordered with each RTU. These are not needed with the expansion chassis.
VA00905 - ADD: +/- 24/48 VDC Power Operation
V266 - ADD: AC Power Operation
The VA00874 ADD: Aux I/O Server Firmware Current ASTRO Release option should be ordered with the RTU to add the required application software.
If desired, punch blocks may be ordered with the RTU by using the V592 ADD: Punch Blocks option. MCC Series I/O Shelf
The MCC Series I/O Shelf can be used with the SDM3000 RTU to provide any required external relays and/or inverters. The MCC Series I/O Shelf interfaces to the SDM3000 RTU via the RTU’s relay outputs and input buffers. There is no data communication link between the two units. It is merely acting as a translator to translate the RTU’s relays into Form B, Form C or double-pole or to translate an active low signal into an active high signal that can be properly detected by the RTU. Please see the MCC 7500 Product Planner and Ordering Guide for more information on this. The MCC Series I/O Shelf is rack mountable in a standard 19 inch rack and is one rack unit high. It consists of a metal chassis, an internal power supply, a controller module and between one and four I/O modules. Each I/O module contains six double pole Form C relays.
The MCC Series I/O Shelf comes standard with one I/O module already in it. Up to three additional I/O modules can be added to provide up to a total of 24 relays. If more than twentyfour relays pairs are needed, additional MCC Series I/O Shelves should be ordered.
RTU Software Upgrades/Downgrades
When upgrading a MCC 7500 console to a newer system release, the software in any SDM 3000 RTUs being used as Aux I/O servers also needs to be upgraded. This is done by ordering the T7955 All Configuration Software and
Firmware to Current Version model with the appropriate option on it. The T7955 provides a single CD containing the
desired software, regardless of how many of the following options are ordered with it.
When upgrading to the current shipping release, the CA02411AA Aux I/O Server Firmware Upgrade option is used. One CA02411AA must be ordered for each Aux I/O server being upgraded. A maximum of 100 of this option can be ordered with a single T7955.
When upgrading to an older release, the CA02405AA Aux I/O Server Firmware Downgrade option is used. One CA02405AA must be ordered for each Aux I/O server being downgraded. A maximum of 100 of this option can be ordered with a single T7955. There is no need to specify which older release is needed because the CD will contain software for all the older releases.
Manuals
Page 2 of 4
Motorola MCC 7500 Products \ MCC 7500 Aux I/O Items
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/CC2CON...
The various manuals for the MCC 7500 dispatch console are included in the ASTRO 25 Radio System Documentation Set. The individual manuals (or the complete documentation set) can be downloaded from the ASTRO 25
Documentation Web Site.
MCC 7500 Product Planner and Ordering Guide
The MCC 7500 Product Planner and Ordering Guide is available on the MCC 7500 wiki page.
Orderable Item Descriptions
Auxiliary inputs and outputs are supported via the SDM3000 Basic Site Manager Remote Terminal Unit (RTU). The RTU can support up to 48 inputs and 16 outputs. If additional inputs or outputs are required, then one or two SDM3000 IO Expansion Chassis may be ordered with the RTU.
An SDM3000 IO Expansion Chassis supports 48 inputs and 16 outputs. One RTU can support up to two expansion chassis for a maximum of 144 inputs/48 outputs per RTU. The SDM3000 IO Expansion Chassis may be ordered by themselves for expanding RTUs which are already installed in the field.
One power option (24/48 VDC or AC) per RTU is required. They are not required for expansion chassis.
The Aux I/O Server Firmware Current ASTRO Release option is used to configure the RTUs being used for dispatch position auxiliary inputs and outputs. One option per RTU is required.
When upgrading or downgrading a RTU, order the T7955 with either the Aux I/O Server Firmware Upgrade or
Aux I/O Server Firmware Downgrade option.
The MCC Series I/O Shelf provides 6 double-pole, Form C relays. Additional relays can be ordered in groups of 6 by ordering the MCC Series I/O Module. A shelf can support a maximum of 24 relays.
Note that a MCC Series I/O Shelf always requires a SDM3000 RTU when part of a MCC 7500 console system.
Links to Other Elements of the Console Sub-System
1. Dispatch Position Items
2. Conventional Channel Gateway Items 3. Auxiliary Input/Output Items
4. Archiving Interface Server (AIS) Items 5. Logging Recorder Items
6. Dispatch Furniture Info 7. Manuals
SDM 3000 Basic RTU
Ordering Requirements
Models
Description Nomenclature APC Price
SITE MANAGER BASIC F4543 469 $1,855.00
The SDM3000 Basic unit is used to provide the AUX I-O functionality for MCC7500 consoles.
The unit is equipped with (1) Ethernet LAN Port, (2) RS-232 ports, (48) Alarm Inputs and (16) Control Outputs.
Use the V2xx options to order 90-250 VAC, 12 VDC, or 20-60 VDC power. Note ? When the 90-250 VAC is selected and the destination country is outside North America, no power cable is included with the unit and it must be provided by the engineer familiar with the power needs of the destination location.
Select the VA00xxx AUX I-O Firmware option specific to the release. The SDM3000 Basic unit includes the following inputs and outputs: - 48 WET or DRY Alarm Inputs
- 16 Electrically Energized Control Outputs
SM IO EXPANSION BASIC F4547 469 $900.00
The F4547 Expansion unit provides additional Alarm Inputs and Control Outputs which can be
Page 3 of 4
Motorola MCC 7500 Products \ MCC 7500 Aux I/O Items
2/17/2015
mk:@MSITStore:C:\Users\case02\Documents\ECAT_DUP_Feb_2015\ECAT.chm::/CC2CON...
Upgrades/Downgrades
New RTU Software Option
This option is used when ordering a new RTU
Fielded RTU Software Upgrade/Downgrade Options
These options are used when upgrading or downgrading an RTU in the field
RTU Power Supply
MCC Series Aux I/O Shelf
Data Compiled 02-Feb-2015 using DUP and all prices in USD
added to the F4544 SDM3000 RTU for ASTRO sites or the F4543 SDM3000 RTU for AUX I-O Server.
The F4544 SDM3000 RTU for ASTRO sites supports up to six expansion units which can be a mix of the F4547 Expansion unit and F4548 Expansion units.
The F4543 SDM3000 RTU for AUX I-O Server supports up to two expansion units which can only be the F4547 Expansion unit.
Use the V2xx options to order 90-250 VAC, 12 VDC, or 20-60 VDC power. Note - When the 90-250 VAC is selected and the destination country is outside North America, no power cable is included with the unit and it must be provided by the engineer familiar with the power needs of the destination location.
The SDM3000 I/O Expansion Basic unit includes the following inputs and outputs: - 48 WET or DRY Alarm Inputs
- 16 Electrically Energized Control Outputs
SDM3000 ALL CONFIGURATION SOFTWARE AND FIRMWARE TO CURRENT VERSION
T7955 382 $0.00
Options
Description Nomenclature APC Price
ADD: AUX I-O SERV FW CURR ASTRO REL VA00874 469 $175.00
ADD: AUX_I-O_SERVER FIRMWARE UPGRADE CA02411AA 382 $925.00
ADD: AUX_IO_SERVER AND AUX_IO_COMPARATOR FIRMWARE DOWNGRADE
CA02405AA 382 $50.00
ADD:24/48 VDC PS TO SM VA00905 469 $120.00
ADD: 90VAC TO 260VAC PS TO SM V266 469 $120.00
This option includes the FKN8266 power cord when shipped to North America. When shipped outside North America the field must supply the applicable power cord.
Accessories
Description Nomenclature APC Price
MCC SERIES I/O SHELF W/ CONTROLLER & CABLE L3468 322 $1,100.00
Includes 12 Inputs and 6 Outputs. Additional I/O modules (TT04532AA) can be added (up to 3).
ADD: MCC SERIES I / O MODULE II TT04532AA 322 $800.00
ORDER with L3468 Model. Includes 12 Inputs and 6 Outputs.