ACOME. Complete systems for: radiant floor heating/cooling/plumbing.

(1)

ACOME

Complete systems for:

(2)

Plumbing systems

Hot and cold water distribution

Principle:

The appliances (plumbing, radiators, fan-coil units, etc.) are

individually supplied

from a

header / distributor.

Direct connection, without discontinuity or couplings,

is done by ducted PEX-c or PB

pipes incorporated into the structures (see diagrams) or by surface-mounted multi-layers.

A complete system – The components:

• PEX-c, PB or multi-layer pipes (with or without ducts) which meet with international

requirements (see page 4, pipes can be supplied by ACOME).

• Complete range of NF or DIN crimped fittings

• Accessories for inlets and outlets in structures

• Header / Distributor

• Valves and accessories

• Manual or battery-operated crimping guns

A large number of advantages:

• Easy installation = less time required

Fewer nuisances = absorption of circulation area noises, decreased heat losses

• Increased safety = elimination of pipework corrosion and furring

(3)

Hydraulic and electric

Four comple

Hydraulic under floor heating / cooling

Installed with a concrete slab or a wet screed

Hydraulic under floor heating

Dry solution, installed without any concrete

More than 20 years experience and references:

over 30,000,000 m

2

_{of Acome floors have been laid across the world}

Innovation prizes

Nominated at the Paris international Interclima 2004 trade show

Installed within 22 mm!

Re

al thi

22 m

W

ALL / P

ARTITION

Permanent elasticity joint Skirting Peripheral insulation 2 PEX-c pipes PE /aluminium undercoat Floating floor PSE slab with aluminium film

Support

Skirting Floor finish

W

ALL / P

ARTITION

Permanent elasticity joint Peripheral insulation PEX-c pipe

Isolation slab on pads

Support

Anti-shrinkage web (if required)

Concrete slab or wet screed

• Thin system:

taking 22 m

• Lightweight system:

very

• System that can be laid o

• Easy system:

very quick i

• Dry system:

premises are

ACOME under floor heating systems are used to provide total or partial heating or heating/coolin

apartment blocks, and in the business sector: offices and factories. They are fully adapted to schoo

stadiums. They can also be used outdoors to prevent the formation of black ice, as solar panels, etc

(4)

c under floors heating

ete systems

Electric under floor heating, permanent output cable

Installed with a concrete slab or a wet screed

W

ALL / P

ARTITION

Skirting Permanent elasticity joint

PE /aluminium undercoat Peripheral insulation Self-regulating cable Floating floor

Support

ickness

m

Skirting Floor finish Underfloor form (if required)

W

ALL / P

A

RTITION

Permanent elasticity joint Peripheral insulation

Permanent output cable on plastic mesh grid

Isolation slab on pads

Support

Anti-shrinkage web (if required)

PSE slab with aluminium film

mm

y little added load

over

existing floor

installation

immediately usable

ng. They can be used to cover all site configurations: new or retrofit works for family homes and

ls, hotels, restaurants and churches as well as sports complexes: gymnasiums, swimming pools and

c.

Concrete slab or wet screed

Electric under floor heating, self-regulating cable

Dry solution, installed without any concrete

A real innovation!

Installed within 22 mm!

(5)

Customised systems

The components:

With over 20 years experience and references across the world, ACOME obviously to be your

industrial partner, allowing you to provide your clients with complete solutions, whether for hot

and cold water distribution, radiators and convectors or for hydraulic or electric under floor

heating systems. A few examples:

• The PEX-c pipe

ACOME provides a full range of pipes, from DN 12 to DN 25, either uncovered or ducted.

• PSE pipe-guide slabs

ACOME provides a range of PSE slabs, thickness according to requirements, for floor heating

systems.

• Header/distributor kit

This kit distribution between the generator and the heating unit.

… /…

The components meet the standards and certifications in force in the following

countries:

STANDARD

CERTIFICATION

Germany Netherlands GB USA France Italy BRL 5606 BRL-K536 / 04 KOMO KIWA BS 7291 NF T 54085 Technical assesment CSTBat certification

Attestation of Sanitary Conformity

DIN CERTCO DIN 4726 DIN EN 15875 DIN CERTCO BBA ASTM F876 / F877 NSF 14 NSF ICC

STANDARD

CERTIFICATION

Spain Switzerland Canada Czech Republic Belgium DIN CERTCO CSA DIN CERTCO DIN CERTCO CSA B 137.5 UNE EN 15875 AENOR DIN 4726 DIN EN 15875 DIN 4726 DIN EN 15875 DIN 4726 DIN EN 15875 DIN 4726 DIN EN 15875

(6)

ACOME worldwide

Industrial facilities – France: Mortain / China: Wuhan and Xintai / Brazil: Irati