Cri
mpi
ng
Tool
s
Tool
s
f
or
the
appl
i
cati
on
of
:
I
nsul
ated
and
Uni
nsul
ated
Sol
derl
ess
Termi
nal
s
Cabl
e
Lugs
Ferrul
es
Open
Barrel
Termi
nal
s
Turned/Mi
l
l
ed
Contacts
RJ
&
Ethernet
Connectors
Crimping Tools for Solderless
Electrical Terminals and Ferrules
Professional crimping tools for solderless terminals must compress the whole length of the terminal’s “barrel” without damaging the individual strands of the conductor and without breaking the terminal itself. The conductor shall be secured that it shall not be pulled out of the crimped terminal. Some terminals require a double crimping operation.
The crimp shape produced by quality tools can vary from a simple indent to a single or double flat mark, or a concentric hexagonal shape.
The tool used must match the type of solderless terminal which must be crimped, both in type and in wire gauge. With regards to type, different tools are required for each of the following styles of terminals:
insulated solderless terminals;
miniature solderless terminals (smaller than 22AWG);
power solderless terminals larger than 8AWG (in most cases, uninsulated);
“Flag” solderless insulated terminals;
Closed-end connectors;
“open-barrel” uninsulated terminals;
All ITC tools are covered by a 12-month parts and labour warranty.
Tools for UNINSULATED TERMINALS
Ratcheting Industrial-grade crimping tools 22-6AWG
Three industrial-grade ratcheting crimping tools covering a wide range of wire gauges. These tools crimp uninsulated terminals from 0.5 to 16 mm2 (22 to 6AWG) with side entry. Crimp shape is indent.
Material: Hardened steel. Plastic-coated handles.
How to Order (Order by Part No.):
Part No. Model Description Max Wire size Length (mm) Weight (g)
500.052 HD 156 Industry grade crimper 0.5-6 mm2 22-10AWG 225 490
500.053 HDTP 68 Industry grade crimper 10-16 mm2 8-6AWG 242 540
Information subject to change without notice
Manual crimping tools for uninsulated power terminals (>8AWG)
Two manual ratchet-action tool, with long handles to minimize operator’s effort, for crimping uninsulated terminals from 6 to 25 mm2 (10 to 4AWG). Material: steel, hardened die, plastic coated handles. Imprint shape on terminals is indent for model HD-25L (p/n 500.065) and hexagonal for model HD-25X (p/n 500.055).
ITC’s manual, rotating-die crimp tool type CT38 (Part No. 500.038) (non-ratcheting) is very practical and economical, as the female die can be selected by simple rotation among the values: 10mm2 (8AWG) – 16mm2 (6AWG) – 25mm2 (4AWG) – 35mm2 (2AWG). Long handles minimize operator effort.
Finally, the heavy-duty single-die crimp tool type HD120 (part No. 500.620) is a non-ratcheting single-die heavy-duty tool, designed for crimping uninsulated terminals from 16 to 120 mm2 (approx. 6 to 4/0AWG). It requires no separate or rotating dies: adjustment is made by turning a knurled screw on the tool’s head. Among its features:
appropriate for most types of solderless power terminals. No risk of losing any dies.
single indent crimp.
long handles make operation extremely easy even for the largest wire size.
die made of tempered steel. Handles of high tensile strength aluminum tubing with plastic grip.
Crimping range for HD-120: (AWG values are approximate - Tool is rated in mm2 and not in AWG):
mm2 1 6 25 35 50 70 95 120
AWG 6 4 2 1 00 000 0000
Screw adjustment allows setting to intermediate values
How to Order (Order by Part No.):
Part No. Model Description Wire size Length (mm) Weight (g)
500.065 HD-25L Industry grade crimper 6-25mm2 10-4AWG 354 780
500.055 HD25X Industry grade hex imprint crimper 6-25mm2 10-4AWG 354 780
500.038 CT 38 Rotating die crimp tool for uninsulated power
terminals 10 to 35 mm2 8-2AWG 580 2,720
500.620 HD120-LT Single die heavy-duty crimp tool for uninsulated
power terminals 16 to 120 mm2 6 – 4/0AWG 645 2,900
Information subject to change without notice
Crimping Tools for open-barrel terminals
Two crimping tools specifically designed for crimping open-barrel brass/copper terminals 26 to 10AWG
Two professional tools: model PEW-16.53 and PEW-16.50, high-precision ratcheting tools for crimping terminals 26 to 10AWG.
Features:
No adjustment needed: All tools cover different sizes of terminals in
different die slots.
Light weight: Tools weigh respectively only 210 g. (economy model) and
550g.(professional models).
Ergonomic design: Comfortably shaped handles and optimal lever design
facilitate
crimping with minimal effort.
How to Order (Order by Part No.):
Part No. Model Description Wire Size Weight (g)
500.310 PEW-16.53 Professional crimping tool for open barrel terminals 0.15 – 1.75 mm2 26 - 15AWG 550
500.311 PEW-16.5 Professional crimping tool for open barrel terminals 0.5 – 6.0 mm2 22 - 10AWG 550
Crimping Tools for INSULATED TERMINALS
Ratcheting Industry-grade Crimping Tools for
Insulated Terminals
These industry-grade ratcheting crimping tools are extremely popular. Model HD0560 (part No. 500.060) crimps the red, blue and yellow insulated terminals from 0.5 to 16 mm2 (22 to 6AWG), while model LY8-067 (part No. 500.062)crimps the “miniature” range 0.14-1.0mm2. Side entry. Crimp shape is indent.
Material: hardened steel. Plastic-coated handles.
How to Order (Order by Part No.):
Part No. Model Description Wire Size Length (mm) Weight (g)
500.060 HD 0560 Industry grade crimper for insulated
terminals 0.5-6 mm2 22-10AWG 225 510
500.062 LY8-067 Industry grade crimper for miniature insulated terminals 0.15-1 mm2 24-18AWG 205 390
Information subject to change without notice
Premium crimping tools for 22-10AWG insulated terminals (ratcheting)
Covering the most common range of insulated crimp terminals (red 22-16AWG, blue 16-14AWG and yellow 12-10 AWG,) these tools offer ergonomic handles, extreme precision and durability. Lightweight yet powerful, model PEW9.20 (part No. 500.064) is designed to operate within confined spaces. Side terminal insertion. Crimp shape is indent.
Material: hardened steel. Ergonomic plastic-coated grips.
How to Order (Order by Part No.):
Part No. Model Description Wire size Length (mm) Weight (g)
500.064 PEW 9.20 Professional crimp tool for insulated terminals 0.5 –
10 mm2 22-10AWG 215 780
Information subject to change without notice
Ratcheting crimp tools for flag terminals
Flag disconnect crimp terminals, due to their particular shape, require specialize tools for crimping. ITC offers two models, one for insulated, one for uninsulated flag terminals 0.5 to 2.5 mm2 (22 to 14AWG).
Material: hardened steel. Plastic-coated handles.
How to Order (Order by Part No.):
Part No. Model Description Wire size Length (mm) Weight (g)
500.069 HD-25L Manual ratcheting crimp tool for insulated flag disconnect terminals 0.5-2.5mm2 22-14AWG 258 650
500.159 HD-NF1 Manual ratcheting crimp tool for uninsulated flag disconnect terminals 0.5-2.5mm2 22-14AWG 225 560
Ratcheting crimp tool for closed-end connectors
This specialized tool (part No. 500.050) crimps closed end insulated terminals (caps) and WPS (waterproof splice) terminals from 1.5 to 6 mm2 (22 to 10 AWG). Side entry, 3 slots. Material: hardened steel. Plastic-coated ergonomic handles.
How to Order (Order by Part No.):
Part No. Model Description Wire size Length (mm) Weight (g)
500.050 XLCD125 Manual ratcheting crimp tool for insulated close end connectors and waterproof splices 1.5-6mm2 22-10AWG 258 650
Information subject to change without notice
Crimp tool kit for uninsulated and insulated terminals and ferrules
This kit (part No. 500.068) consists in one plastic case containing one ratchet operated tool frame and four interchangeable die sets:
for uninsulated terminals 22-10AWG;
for insulated terminals 22-10AWG;
for ferrules 22-10AWG;
for closed end terminals 22-10AWG.
Exchanging the dies is extremely simple and only requires a common screwdriver.
Material: The tool frame is made of steel, with oversize ergonomic plastic handles.
How to Order (Order by Part No.):
Part No. Model Description Wire size Weight (g)
500.068 2000-K4 Crimp tool kit for uninsulated and insulated terminals
and ferrules 1.5-6mm2 22-10AWG 1,200 (box) 650 (tool)
Information subject to change without notice
Crimping Tools for FERRULES (Cord End Terminals)
Crimping tools for ferrules (cord end terminals) must provide adequate pressure along the whole length of the ferrule, and result in a crimped profile which is suitable for the specific application. Serration along the profile of the crimp attains the double result of lessening the possibility of conductor pull-out from the crimped ferrule, and of improving contact between the ferrule and most models of existing wire clamps.
ITC can provide a variety of ferrule crimping tools, from simple plier-type hand crimpers to heavy-duty and automatic stripping/crimping machines. All tools are covered by a 12-month parts and labour warranty.
Economy Plier-type Ferrule Crimping Tools
Model PE7 (part No. 500.047) Precision Ferrule Plier-type Crimper is a precision non-ratchet tool for limited production, for quality crimping single ferrules – uninsulated and insulated – from 0.25 to 2.5 mm2 (24 to 14AWG) or twin ferrules 0.14 to 1.5mm2 (26 to 16AWG) with different crimp indents. Crimp shape is trapezoidal (see picture), ideal for inserting in terminal blocks, contactors, circuit breakers.
Material: special tool steel, hardened and polished.
Plastic-coated handles.
How to Order (Order by Part No.):
Part No. Model Description Wire size (*) Length (mm) Weight (g)
500.047 PE7 Precision plier-type crimper 0.25 – 2.5 mm2 24-14AWG 150 140
Standard, Industrial-grade Ratcheting Ferrule Crimping Tools
Type CE Ferrule crimping tools are three industrial-grade ratcheting ferrule crimping tools covering altogether a wide range of wire gauges. All these tools crimp single ferrules – uninsulated and insulated – from 0.5 to 35 mm2 (22 to 2AWG) or twin ferrules 0.3 to 25mm2 (24 to 4AWG) with different crimp indents.
Material: hardened steel. Plastic-coated grips.
How to Order (Order by Part No.):
Part No. Model Description Wire size (*) Length (mm) Weight (g)
500.036 CE1635 Industry grade ferrule crimper 16-35 mm2 6-2AWG 226 540
500.040 CE002 Industry grade ferrule crimper 0.5-6 mm2 22-10AWG 205 390
500.041 CE003 Industry grade ferrule crimper 4-16 mm2 12-6AWG 205 390
500.169 CE1 Replacement jaw, crimper CE001 22-14AWG - 35
500.170 CE2 Replacement jaw, crimper CE002 22-10AWG - 35
500.171 CE3 Replacement jaw, crimper CE003 12-6AWG - 38
Information subject to change without notice – (*)refers to single ferrules
Heavy-duty, Industrial-grade Ferrule Crimping Tools
Model A42 Heavy duty manual Ferrule crimping tool (part No. 500.042) is a ratchet tool capable of crimping single ferrules – uninsulated and insulated – from 25 to 50 mm2 (4 to 1 AWG) with different crimp indents. Crimp shape is trapezoidal.
Material: hardened steel. Plastic-coated grips.
ITC’s unique model CS70150 Heavy duty Vice-mounted Ferrule crimping tool is an ingenious device (part No. 500.051), which uses the pressure available in a standard bench-mounted vice to crimp large ferrules without using expensive hydraulic tools. It is capable of crimping uninsulated and insulated single ferrules from 70 to 150 mm2 (2/0 to 250MCM) with different crimp indents. Crimp shape is trapezoidal.
Material: hardened steel, polished.
How to Order (Order by Part No.):
Part No. Model Description Wire Size Length (mm) Weight (g)
500.042 A42 Heavy-duty ferrule crimper 25-50 mm2 4-1 AWG 300 650
500.051 CS70150 Vice-mounted ferrule crimper 70-150 mm2 2/0 AWG –
250MCM 125x100 2300
500.054 CS150240 Vice-mounted ferrule crimper 150-240 mm2 125x100 -
Professional, Ratcheting Ferrule Crimping Tools
Type AE professional, patented ratchet-action ferrule crimping tools feature parallel-action crimping, meaning that the same pressure is applied along the whole length of the ferrule. Front loading makes access to reduced space easier. Single-die operation means that there is no possibility of choosing the wrong slot for crimping a ferrule – the tool self-adjusts to the proper section, without variation in crimping pressure.
Crimp shape: trapezoidal. Material: tempered steel, burnished. Ergonomic grips in polyurethane compound.
Type PEW 8.85 and 8.86 ratchet-action ferrule crimping tools feature square or hexagonal crimping shape, obtained by means of synchronous driven crimp jaws. As a result, the same pressure is applied along the whole length of the ferrule and the shape is ideal for installation in wire clamps (square crimp) or in screw-pressure wire terminals (hexagonal crimp). Side loading on both models, single-die operation (the tool self-adjusts to the proper section, without variation in crimping pressure).
Type PEW 8.88 (part No. 500.049) is a ratchet-action ferrule crimping tool with front access and square crimp shape. A 2-position lever extends the maximum crimping range (from 28AWG) to a maximum of either 7AWG or 5AWG: the widest crimp range of all our tools!
Crimp shapes: see illustrations below. Material: tempered steel, burnished. Ergonomic grips in polyurethane compound.
500.035
500.039
500.049
How to Order (Order by Part No.):
Part No. Model Description Wire size (*) Length (mm) Weight (g)
500.030 AE2 Professional front-load crimp tool 0.14-6mm2 28-10AWG 210 500 500.031 AE3 Professional front-load crimp tool 2.5-10mm2 14-8AWG 225 500 500.032 AE4 Professional front-load crimp tool 10-16mm2 8-6AWG 230 650 500.035 PEW 8.84 Professional square die crimp tool 0.08-6mm2 28-8AWG 180 380 500.039 PEW 8.86 Professional hex die crimp tool 0.08-6mm2 28-10AWG 180 380 500.049 PEW 8.88 Professional front-load square die crimp tool
10-16mm2 28-5AWG 190 475
Type AE Heavy duty precision Ferrule crimping tools
This family includes two heavy-duty, professional quality crimping tools for uninsulated and insulated ferrules in the range from 10 to 95 mm2 (8 to 3/0 AWG) with different crimp indents. Crimp shape is trapeze.
Material: hardened/tempered steel. Blue plastic-coated handles.
500.033 500.034
How to Order (Order by Part No.):
Part No. Model Description Wire Size Length (mm) Weight (g)
500.033 AE7 Heavy-duty precision ferrule crimper 10-50 mm2 8-1 AWG 340 770 500.034 AE8 Heavy-duty precision ferrule crimper 50-95 mm2 1-3/0 AWG 325 800
Information subject to change without notice
“QUADRO” Manual Multifunction ferrule tool
“QUADRO” is a manual tool designed to significantly increase productivity in the termination of control wiring with insulated ferrules. QUADRO (part No. 500.090) performs 4 functions on stranded wires 0.5 to 2.5mm2 (22-14AWG):
Cuts the wire;
Strips the insulation;
Twists the strands;
Crimps the ferrule.
This tool can cut wires up to 2.5mm2 (~14AWG) (with most common types of insulation). It then strips them precisely and safely, and prepares the stripped end by twisting the bare strands: this enables easy insertion in the ferrule. For the final operation, no adjustment is necessary: ferrules are supplied in strips within quick-change magazines (refillable): one last pressure on the handles performs a quality crimp, and the tool is ready for another cycle. Operation is effortless, and the tool weighs less than 1/2lb. Quadro is approved by TÜV-GS (Germany) and carries the CE mark.
How to Order QUADRO Ferrule Tool (Order by Part No.):
Part No. Description Wire size Weight (g)
500.090 “Quadro” multifunction tool, with case and 3 magazines 22-14AWG 285
500.092 Spare magazine - 10
170.508 Insulated ferrule 0.50mm2, 5 strips of 50 pieces 22AWG 5 / strip 177.508 Insulated ferrule 0.75mm2 5 strips of 50 pieces 20AWG 5 / strip 171.008 Insulated ferrule 1.00mm2 5 strips of 50 pieces 18AWG 5 / strip 171.508 Insulated ferrule 1.50mm2 5 strips of 50 pieces 16AWG 5 / strip 172.508 Insulated ferrule 2.50mm2 5 strips of 40 pieces 14AWG 5 / strip
Pneumatic Crimping Tool for Electrical Terminals
ITC offers an innovative, portable or bench-mounted pneumatic crimping tool for increased
production capability.
The A200 tool consists of a light-weight air cylinder and an interchangeable “jaw” or die. Sixteen different types of dies are available for most types of insulated or uninsulated crimp terminals, ferrules or telephone jacks. Working air pressure:
90 – 120 PSI (6-8 kg.).
Crimping “jaws” are easily replaced on the air cylinder by loosening the assembling pin. Two models of air cylinder are in stock: Standard and High Power (the latter for up to 12-10 AWG and nylon insulated terminals).
[NOTE: Standard model to be discontinued]
Jaws for crimp terminals are equipped with the exclusive ITC positioning device, which holds the terminal in position for precise, quick and safe crimping. This positioning device can be easily adjusted to fit terminals of various diameters, lengths, and thicknesses.
Available accessories include:
Bench mounting attachment.
Pneumatic foot switch and approx. 5’ of flex air hose, for hands-free operation.
Pneumatic Crimping Tools And Accessories (order by part Number):
Part No. Model Description Terminal size: Position. device Use Cylinder model:
500.902 A-200-1 Pneumatic Cylinder, Hi-power - - -
500.903 YS-301 Hand-free cylinder holder - - -
500.909 ACE-2536 Foot switch for pneum. tools, with hose/conn. - - -
500.910 - Replacement jaw without dies - - -
500.125 IT-125 Crimp jaw for insul. terminals 22-16AWG Yes A-200-1 or -2 500.126 NT-125 Crimp jaw for uninsul. terminals 22-16AWG Yes A-200-1 or -2
500.127 IT-125N Crimp jaw for insul. nylon terminals 22-16AWG Yes A-200-1 only 500.128 CE-125 Crimp jaw for insul. closed end connectors 22-16AWG Yes A-200-1 or -2
500.200 IT-200 Crimp jaw for insul. terminals 16-14AWG Yes A-200-1 or -2 500.201 NT-200 Crimp jaw for uninsul. terminals 16-14AWG Yes A-200-1 or -2
500.202 IT-200N Crimp jaw for insul. nylon terminals 16-14AWG Yes A-200-1 only 500.203 CE-200 Crimp jaw for insul. closed end connectors 16-14AWG Yes A-200-1 or -2
500.500 IT-500 Crimp jaw for insul. terminals 12-10AWG Yes A-200-1 only
500.501 NT-500 Crimp jaw for uninsul. terminals 12-10AWG Yes A-200-1 only 500.502 IT-500N Crimp jaw for insul. nylon terminals 12-10AWG Yes A-200-1 only 500.503 CE-500 Crimp jaw for insul. closed end connectors 12-10AWG Yes A-200-1 only
500.510 IT-500A Crimp jaw for insul. Cooper terminals 12-10AWG Yes A-200-1 only 500.520 ST-200 Crimp jaw for strip term.- closed barrel 18-16AWG Yes A-200-1 or -2 500.530 RJ-45 Crimp jaw for telephone jacks RJ45 - No A-200-1 or -2 500.560 CO-0560 Crimp jaw for ferrules 22-10AWG No A-200-1 or -2 Information subject to change without notice.
Pneumatic Ferrule Crimping Tools
ITC introduces a new family of pneumatic tools for crimping wire end ferrules 24 to 8AWG.
Hand-held Pneumatic Crimping Tools for Ferrules 0.25 –10 mm
2(24 to 8AWG
)
Two models of hand-held pneumatic crimping tools are offered by ITC: Model AC25, for ferrules 0.25 to 2.5 mm2 (24-14 AWG), single die, ferrule insertion from either front or side of the head.
Model AC100, for ferrules 4.0 to 10 mm2 (12-8 AWG), ferrule insertion from side of tool only.
Both tools require compressed air at 4 to 6 bar (90 to 120 psi), are controlled by a pressure lever on the body of the tool itself, and are equipped with a finger guard for safety. They come equipped with a pneumatic hose and a connector.
Tool length: 200 mm (~8”).
How to Order (Order by Part No.):
Part No.
Description/model
Weight (g)
500.952 Pneumatic hand-held crimper for 24-14 ferrules, type AC25 430
500.962 Pneumatic hand-held crimper for 12-8 ferrules, type AC100 460
Information subject to change without notice
Bench-mount Pneumatic Crimping Tools for Ferrules 0.25 –10 mm
2(24 to 8AWG)
Two models of bench-mount pneumatic crimping tools are offered by ITC:
Model AC25T, for ferrules 0.25 to 2.5 mm2 (24-14 AWG), single die, ferrule insertion from either front or side of the head.
Model AC100T, for ferrules 4.0 to 10 mm2 (12-8 AWG), ferrule insertion from side of tool only.
Both tools require compressed air at 4 to 6 bar (90 to 120 psi), are controlled by a foot switch (supplied), and are equipped with a finger guard for safety as well as a handy ferrule tray on the body of the tool. They come equipped with pneumatic hose, foot switch, and bench mount clamp.
How to Order (Order by Part No.):
Part No.
Description/model
Weight (g)
500.951 Pneumatic bench mount crimper for 24-14 AWG ferrules,
type AC25T
1000
500.961 Pneumatic bench mount crimper for 12-8 AWG ferrules,
type AC100T
1000
Power Crimping Tools
ITC can provide a variety of solutions for crimping copper
cable lugs from 8AWG through 500MCM.
The Model HT51 is a compact two-stage Hydraulic Crimping Tool
that delivers 6 Tons of force and features spring-loaded handles
and a 180º rotating head for ease of use.
The Model RH50 is a Hydraulic Presshead that can be attached
to your existing hydraulic source, and operates at up to 10,000
psi.
The Model B51A is a 14.4V Battery Operated Crimping Tool that
delivers 6 tons of crimping force, has a rotating head and is
supplied in a case including the tool, charger, 2 batteries and
a wrist and shoulder strap.
All units on this page use the same crimping dies (sold separately, see below).
Crimping tools for up to 1500MCM are also available, please inquire for details.
Features:
Crimping force: 6 tons.
Max operating pressure: 10,000psi.
All tools provided in plastic carrying case.
Crimp copper terminals 8AWG to 500MCM.
1 Year Manufacturer’s Warranty.
Hydraulic Crimping Tools (Order by Part No.):
Part No. Model Description Dimensions (L x W) mm Weight (g)
502.551 HT 51 Two stage hydraulic tool - 6 Tons of force. 38.4 x 12.8 2682 502.559 RH 50 Hydraulic presshead - 6 Tons of force. 19.7 x 7.7 1591
502.550 B51A 14.4 Volt Battery operated tool. -
502.101 MY 2-50 Die set, for HT51, B50 tools, 8AWG - 502.102 MY 3-50 Die set, for HT51, B50 tools, 6AWG - 502.103 MY 4-50 Die set, for HT51, B50 tools, 4AWG - 502.104 MY 5-50 Die set, for HT51, B50 tools, 3AWG - 502.105 MY 6-50 Die set, for HT51, B50 tools, 2AWG - 502.106 MY 7-50 Die set, for HT51, B50 tools, 1AWG - 502.107 MY 10-50 Die set, for HT51, B50 tools, 1/0AWG - 502.108 MY 14-50 Die set, for HT51, B50 tools, 2/0AWG - 502.109 MY 16-50 Die set, for HT51, B50 tools, 3/0AWG - 502.110 MY 19-50 Die set, for HT51, B50 tools, 4/0AWG - 502.111 MY 24-50 Die set, for HT51, B50 tools, 250MCM - 502.112 MY 30-50 Die set, for HT51, B50 tools, 300MCM - 502.113 MY 36-50 Die set, for HT51, B50 tools, 350MCM - 502.114 MY 37-50 Die set, for HT51, B50 tools, 400 MCM - 502.115 MY 48 Die set, for HT51, B50 tools, 500 MCM - Information subject to change without notice
Specialty Crimping Tools for Electrical Terminals
Crimping tool for D-Sub Contacts
The new HD-1440 Crimp tool by ITC precisely crimps D-sub contacts for RS232 interface connectors.
Features:
Ratchet action: The ratchet mechanism guarantees that each crimping operation
is performed completely, eliminating the risk of poor connections.
Precision 4-way indent dies.
Minimal manual effort: ergonomic design. Handles are ergonomically shaped and
plastic coated.
Material: Metal body, heat-treated dies.
Warranty: 1 year covering manufacturer defects.
From stock in Canada.
Crimping Tool for D-Sub Contacts (Order by Part No.):
Part No. Model Description Wire range
(mm2) Wire range (AWG) Length (approx.) Weight (approx.)
500.024 DD-1440 Crimp tool for D-SUB contacts 0.14-0.75 26-20 163mm 250 g.
Information subject to change without notice
Cutting / Stripping / Crimping tools for Modular Telephone Terminals
The all-in-one Wire cutter/stripper/crimpers by ITC are the economical, perfect tools for telephone and
network installers.
Features:
Cuts telephone 2, 4, 6 and 8-conductor wires.
The precision stripper strips the external jacket of the wire, without
damaging the individual conductors.
Ratchet action: The ratchet mechanism guarantees that each crimping
operation is performed completely, eliminating the risk of poor connections.
Warranty: 1 year covering manufacturer defects.
From stock in Canada.
Tools for Modular Telephone Terminals (Order by Part No.):
Part No. Model Description Length
(approx.)
Weight (approx.)
500.155 ASR-486 Professional strip/crimp ratchet tool for 2/4/6/8 pole modular jacks 228mm 410 g.
Information subject to change without notice