Trio Q Data Radios. Licensed UHF Ethernet and Serial Data QR450

(1)

Trio Q Data Radios

Licensed UHF | Ethernet and Serial Data

(2)

The Trio Q Data Radios are advanced high speed licensed digital data

radios, which provide both Ethernet and serial communications for

the most complex and demanding applications in Point-to-Point and

Point-to-Multipoint (Multiple Address Radio) Telemetry and remote

SCADA systems.

Features such as ChannelShare+™, web-based user configuration,

together with powerful remote diagnostics and Network

Management, make Trio Q Data Radios the complete licensed

radio solution that works with all leading host systems and remote

equipment.

Combining both Ethernet and serial connectivity, the Trio Q Data

Radios are suitable for use with the latest SCADA technology as well

as providing a smooth transition from serial-based infrastructure to

IP/Ethernet.

(3)

Trio QR450

Radio

Frequency Range 400-450MHz (M-Band) or 450-520MHz (H-Band) Frequency Splits Various Tx/Rx frequency splits - configurable Channel Selection 3.125kHz channel steps

Channel Spacing 12.5 and 25kHz (software selectable) Frequency Accuracy ±0.5ppm, -40 to +70°C (-40 to 158°F) ambient Aging <= 1ppm/annum

Radio Modes Simplex and Half duplex

Configuration Configuration via embedded HTTP, HTTPS web interface & or Telnet/SSH/Serial console

Transmitter

Tx Power 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Modulation Configurable narrow band digitally filtered binary CPM, 4, 8 and 16 level FSK

Tx Keyup Time <1ms

Timeout Timer Configurable 0 to 255 seconds Tx Spurious <= -37dBm

PTT Control Auto (Data) / RTS line on Data Port

Receiver

AFC Tracking Digital receiver frequency tracking Mute Configurable digital mute

Connections

Serial Com Port 1/2 1 x DB9 female connector providing 2 x RS-232 3-wire serial ports or 1x RS485 serial port (shared connector). Serial Interface Speeds From 600bps up to 115,200bps

Serial Com Port Flow Control Configurable hardware / software / 3-wire interface

Serial Com Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 2 x RJ45: 10/100 Mbps (auto-MDIX sensing) compliant with IEEE 802.3 Antenna 1 x TNC female bulkhead

Power 2-pin locking, mating connector supplied

USB port Firmware Upgrade, Configuration & Diagnostics logs (Future release) LED Display Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs

Ethernet

Ethernet Protocols Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT) Ethernet Repeating Automatic and Self Learning Peer to Peer repeating

Operating Modes Layer-2 Ethernet Bridge mode / Layer-3 IP Router mode

Ethernet Traffic Filtering Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Compression Automatic Ethernet data compression

Terminal Server Legacy RS-232 serial support via embedded terminal server (UDP/TCP) DHCP Modes Auto and Manual

SNMP SNMP V1,V2c, RFC 1213-compliant & radio diagnostics parameters (with traps) Modbus Gateway Configurable MODBUS/TCP to MODBUS/RTU Gateway

Embedded Ping Tester Internal ping test facility Specifications continue on the next page

Product Data Sheet Trio QR450

Specifications

(4)

Trio QR450

Modem

RF Channel Data Rate # Region Bandwidth (KHz) Speed (Kbps) RF Sens (1x10E-6 BER) FCC 12.5 8 16 24 32 -116 -111 -105 -97 25 16 32 48 64 -114 -109 -103 -96 ACMA/ETSI 12.5 8 16 24 32 -113 -110 -107 -100 25 14 28 42 56 -114 -109 -103 -96 Dynamic Speed Selection QoS/RSSI based Automatic Speed Selection or Fixed speed mode

Operating Modes Base, remote, repeater or store n’ forward

Channelshare+™ Advanced dynamic supervisory collision avoidance system Backward Compatibility Backward compatible with Trio E-Series radios

Firmware Local and over-the-air flash-based firmware upgradable patches with support for broadcast updates

Security

Encryption* 256-bit AES

HTML Interface Password Protected HTTP and HTTPS configuration and management interface Console Interface Password protected Telnet, SSH and Serial console interface

Password Protection Password protected configuration sessions

Diagnostics

Diagnostics Overview • Network management and diagnostic Windows GUI software • Network-wide operation from any remote terminal • Non intrusive protocol – runs simultaneously with the application • Storage of data error and channel occupancy statistics • In-built Error Rate testing capabilities • Diagnostics parameters available • Transmitter Power • Received Signal Strength • DC Supply Voltage • Received Frequency Error • Radio Temperature • VSWR

Event Log Internal Event Logging facility

General

Operating Temperature Range -40 to +70°C (-40 to 158°F) ambient Power Supply 13.8Vdc nominal (10-30Vdc)

Transmit Current 1.6A nominal @ 1W, 2.7A nominal @ 5W, 3.7A nominal @ 10W Receive Current <330mA nominal @ 13.8Vdc

Housing & Dimensions Rugged die-cast, 115 x 34 x 164mm

Mounting Integrated Mounting Holes or DIN Rail mounting (optional) Weight 0.5kg (1.1lbs.)

Warranty 3 years on parts and labor

Approvals and Certifications

Europe (ETSI) ETSI EN300113, EN301489, EN60950 FCC FCC PART 15, PART 90

Industry Canada IC RS119, ICES-001 Australia ACMA AS4295-1995 (Data)

Hazardous Locations CSA Class I, Division II, Groups (A,B,C,D) for Hazardous Locations ANSI/UL equivalent)

Product Data Sheet Trio QR450

Specifications

(5)

TBURQR4ab-cccdeef represents the part number matrix

Model

Trio Radio QR450

TBURQ Q Data Radios

Code

Select: Unit Type

R Simplex/Half Duplex Radio

Code

Select: Generic Frequency Band

4 UHF: 400 - 520 MHz Band

Code

Select: Sub Band - UHF

L Low Band : 400 to 450MHz H High Band : 450 to 520MHz

Code

Select: Hazardous Area Approvals

H CSA & ATEX Hazardous (Standard)

Code

Select: Modulation

E00 ETSI/ACMA Region F00 FCC Region

Code

Select: Encryption (subject to country of use)

E 256-bit AES encryption (standard) N No encryption

Code

Select: Licensed Feature

0L Serial Data Only (Two Serial Ports)

1L Ethernet & Serial (Three Ethernet & two Serial Ports)

Code

Select: Power Supply

0 10-30V DC Standard

Example: TBURQR4LH-E00E1L0 specifies: Trio QR450 remote station, 400 to 450MHz, hazardous area approved, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, two Ethernet & two Serial Ports, 10-30V DC power supply

Communications Standards:

FCC – Federal Communications Commission (USA) IC – Industry Canada

ETSI – European Telecommunication Standards Institute ACMA – Australian Communications and Media Authority

* Export restrictions may apply. Contact your local representative for more details. Note: Not all product features are available in every mode of operation.

Note: Some radio models may not be available in your country. Local and regulatory conditions may determine the performance and suitability of the radio in different countries. It is the responsibility of the buyer to ensure the radio model meets the regulatory conditions required. Contact your local Schneider Electric sales office for more details.

Product Data Sheet Trio QR450

Model Code

(6)

Trio Q Data Radios

Licensed UHF | Ethernet and Serial Data

(7)

The Trio Q Data Radio is an advanced high speed licensed digital data

radio which provides both Ethernet and serial communications for

the most complex and demanding applications in Point-to-Point and

Point-to-Multipoint (Multiple Address Radio) Telemetry and remote

SCADA systems.

Features such as ChannelShare+™, web-based user configuration,

together with powerful remote diagnostics and Network

Management, make Q Data Radios the complete licensed radio

solution that works with all leading host systems and remote

equipment.

Combining both Ethernet and serial connectivity, the Trio Q Data

Radio are suitable for use with the latest SCADA technology as well as

providing a smooth transition from serial-based infrastructure to IP/

Ethernet.

(8)

Trio QB450

Radio

Frequency Range 400-450MHz (L-Band) or 450-520MHz (H-Band) Frequency Splits Various Tx/Rx frequency splits - configurable Channel Selection 3.125kHz channel steps

Radio Modes Simplex, Half duplex & Full duplex

Duplexer Optional external duplexer available for single antenna operation

Transmitter

Tx Keyup Time <1ms

PTT Control Auto (Data)

Receiver

Connections

Serial Com Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-MDIX sensing) compliant with IEEE 802.3

Antenna 2 x N female bulkhead (seperate Tx and Rx ports - full duplex) or optional 1 x N female bulkhead (single Tx/Rx port - half duplex) Power (Supply voltage options) 10-pin locking, mating connector supplied or optional (10-30Vdc/36-72Vdc) or 100-250Vac IEC socket

Ethernet

Product Data Sheet Trio QB450

Specifications

(9)

Trio QB450

Modem

Security

Diagnostics

General

Operating Temperature Range -40 to +70°C (-40 to 158°F) ambient

Internal Fan Internal automatic thermostatically controlled fan

Power Supply 10-30Vdc (nominal) or optional 36-72Vdc or 100-250Vac power supply Protection mode Full duplex (not protected) or optional half duplex (protected) hardware variants Transmit Current** 4A nominal @ 1W, 5.1A nominal @ 5W, 6.1A nominal @ 10W

Receive Current** 1A nominal @ 13.8Vdc

Housing & Dimensions 19” 1 RU rack mount, 483 x 45 x 410mm Weight 5kg (11lbs.)

Approvals and Certifications

Product Data Sheet Trio QB450

Specifications

(10)

TBURQB4ab-cccdeef represents the part number matrix

Model

Trio Radio QB450

TBURQ Q Data Radios

Code

Select: Unit Type

B Full Duplex Radio - 19” 1RU P Half Duplex Protected Radio - 19” 1RU

Code

Select: Generic Frequency Band

Code

Select: Sub Band - UHF

Code

Select: Hazardous Area Approvals

N No Approval

Code

Select: Modulation

Code

Select: Encryption (subject to country of use)

Code

Select: Licensed Feature

0L Serial Data Only (Two Serial Ports)

Code

Select: Power Supply

0 Redundant 10 - 30V DC Standard 1 Redundant -48V DC

2 Non-Redundant 110/240V AC 3 Redundant 110/240V AC

Example: TBURQB4LN-E00E1L0 specifies: Trio QB450 base station, 400 to 450MHz, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, three Ethernet & two Serial Ports, redundant 10-30V DC power supply.

* Export restrictions may apply. Contact your local representative for more details.

** In high ambient temperature situations, the internal fans may operate, resulting in additional current consumption of upto 2 Amps. Note: Not all product features are available in every mode of operation.

6

Product Data Sheet Trio QB450

(11)

Trio Q Data Radios

Licensed UHF | Ethernet and Serial Data

(12)

1

The Trio Q Data Radio is an advanced high speed licensed digital data

radio which provides both Ethernet and serial communications for

the most complex and demanding applications in Point-to-Point and

Point-to-Multipoint (Multiple Address Radio) Telemetry and remote

SCADA systems.

Features such as ChannelShare+™, web-based user configuration,

together with powerful remote diagnostics and Network

Management, make Q Data Radios the complete licensed radio

solution that works with all leading host systems and remote

equipment.

Combining both Ethernet and serial connectivity, the Trio Q Data

Radio are suitable for use with the latest SCADA technology as well as

providing a smooth transition from serial-based infrastructure to IP/

Ethernet.

(13)

Trio QH450

Radio

Radio Modes Full duplex

Duplexer Optional external duplexer available for single antenna operation

Transmitter

Tx Power 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Modulation Configurable narrow band digitally filtered binary GMSK, 4, 8 and 16 level FSK

Tx Keyup Time <1ms

Receiver

Connections (for each Base within the Hot Standby configuration)

Serial Data Port 1 x RS232 DB9 female connector providing 2 x RS-232 3-wire serial ports (shared connector). 300-38,400 bps asynchronous Serial Data Port Flow Control Configurable hardware / software / 3-wire interface

Serial Data Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-MDIX sensing) compliant with IEEE 802.3

Antenna 2 x N female bulkhead (seperate Tx and Rx ports - full duplex) or optional 1 x N female bulkhead (single Tx/Rx port - half duplex) Power (Supply voltage options) 10-pin locking, mating connector supplied or optional (10-30Vdc/36-72Vdc) or 100-250Vac IEC socket

Ethernet

Ethernet Traffic Filtering Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Ethernet Link Monitoring Monitor the Ethernet link between a base unit and up to two remote IP addresses

Compression Automatic Ethernet data compression

Product Data Sheet Trio QH450

Specifications

(14)

Trio QH450

Modem

Security

Hot Standby Controller

Change-over control Manual (forced) / automatic / remote (software driven)

Alarm Monitoring Tx Power Failure / Receiver Failure / Received Signal Frequency Error / Data Corruption / DC Power Supply Fail

Diagnostics

General

Internal Fan Internal automatic thermostatically controlled fan Power Supply 10-30Vdc or optional 36-72Vdc or 100-250Vac power supply

Protection mode Full duplex (not protected) or optional half duplex (protected) hardware variants

Housing & Dimensions Hot Standby is configured using 2 x QB450 (19” 1 RU each) plus 1 x Hot Standby Controller (19” 1 RU each) for a total of 19” 3RU’s (424.3 x 132 x 436.5mm )

Weight 15kg (33Ibs) excluding optional duplexer Warranty 3 years on parts and labor

Approvals and Certifications

Product Data Sheet Trio QH450

Specifications

(15)

Model

Trio Radio QH450

TBURQ Q Data Radios

Code

Select: Unit Type

H Full Duplex Hot Standby Kit (with controller) - 19 “ 3RU Comprised of 2 x QB + Controller

Code

Select: Generic Frequency Band

Code

Select: Sub Band - UHF

Code

Select: Hazardous Area Approvals

N No Approval

Code

Select: Modulation

Code

Select: Encryption (subject to country of use)

Code

Select: Licensed Feature

Code

Select: Power Supply

0 10 - 30V DC Standard 1 -48V DC

2 Single 110/240V AC

Code

Select: Hot Standby Controller Options

A Common Tx/Rx Antenna B Duplicated Tx/Rx Antennas

Note: Refer to the next page for further details on the Hot Standby Controller Options.

Product Data Sheet Trio QH450

Model Code

(16)

TBURQH4xx-xxxxxxxA • 2 x TBURQB4xx-xxxxxxx • 1 x TBURQHHSC-00A TBURQH4xx-xxxxxxxB • 2 x TBURQB4xx-xxxxxxx • 1 x TBURQHHSC-00B QB450 QB450 QB450 QB450

QHHSC Hot Standby Controller Option

A

B

LNA (Low Noise Receiver Amplifier / Splitter) RELAY (Coaxial Transmitter Switch) EXTERNAL DUPLEXER

Kit Configuration

Tx Rx

QH450 - Hot Standby Controller Kit Configurations

16.69” (424mm) 18.87” (479.3mm) 15” (381mm) 5.19” (132mm) 16.7” (424mm) 15.91” (404.3mm)

ETH1 ETH2ETH3 COM 1/2 B AAuto Select QB450 USB Factory Default

ETH1 ETH2 ETH3 AUX Pwr Tx COM1 Rxd Txd Com2 Rxd Txd Error No Yes Sync NoRx < Green < Red QHHSC 15.91” (404.3mm) 16.7” (424.3mm) 17.18” (436.5mm) Base A COM 1/2 QB450 USB Factory Default

ETH1 ETH2 ETH3 AUX Pwr Tx COM1 Rxd Txd Com2 Rxd Txd Error No Yes Sync NoRx < Green < Red COM 1/2 COM 1/2 AUX ETH1

Base B COM 1/2 AUX ETH1

6

Product Data Sheet Trio QH450

Dimensions and Options

Telemetry & Remote SCADA Solutions

|

www.schneider-electric.com Document Number TBULMxxxxxx-xx

QH450 - Hot Standby Full Duplex Radio - Dimensions

QHHSC - Option Descriptions

Description Antenna Type A LNA (Rx) & RF _{Relay (Tx) Fitted} Common Tx/Rx _Antenna B Duplicated Tx/Rx _Ports Duplicated Tx/Rx _Antennas

#Note – The QH450 is a full duplex radio platform and must be deployed with suitable band pass duplexer or external filters. Internal Duplexers are not available. Suitable duplexers include TBURDUPLXBP4XXCOA. For information regarding external duplexers, contact your local sales office.

(17)

Trio Q Data Radios

Licensed UHF | Ethernet and Serial Data

(18)

The Trio Q Data Radio is an advanced high speed licensed digital data

radio which provides both Ethernet and serial communications for

the most complex and demanding applications in Point-to-Point and

Point-to-Multipoint (Multiple Address Radio) Telemetry and remote

SCADA systems.

Features such as ChannelShare+™, web-based user configuration,

together with powerful remote diagnostics and Network

Management, make Q Data Radios the complete licensed radio

solution that works with all leading host systems and remote

equipment.

Combining both Ethernet and serial connectivity, the Trio Q Data

Radio are suitable for use with the latest SCADA technology as well as

providing a smooth transition from serial-based infrastructure to IP/

Ethernet.

(19)

Trio QP450

Radio

Radio Modes Simplex or Half duplex

Transmitter

Tx Keyup Time <1ms

Receiver

Connections

Serial Com Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-MDIX sensing) compliant with IEEE 802.3 Antenna Optional: (See diagram at end of datasheet for detailed information)

- 2 x N female bulkhead (Refer Option B) - 2 x N female bulkhead (Refer Option D) - 1 x N female bulkhead (Refer Option E)

Power (Supply voltage options) 10-pin locking, mating connector supplied or optional (10-30Vdc/-48Vdc) or 100-250Vac IEC socket USB port Firmware Upgrade, Configuration & Diagnostics logs (Future release)

LED Display Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs

Ethernet

Product Data Sheet Trio QP450

Specifications

(20)

Trio QB450

Modem

Collision Avoidance Channelshare+™ - Advanced dynamic supervisory collision avoidance system Carrier Sense - Carrier sense based collision avoidance system

Backward Compatibility Backward compatible with Trio E-Series radios

Security

Diagnostics

General

Internal Fan Internal automatic thermostatically controlled fan

Power Supply 10-30Vdc (nominal) or, for option B hardware, optional -48Vdc or 100-250Vac power supply Protection mode Half duplex - Automatic or manual changeover between internal modules

Transmit Current** 4A nominal @ 1W, 5.1A nominal @ 5W, 6.1A nominal @ 10W Receive Current** 1A nominal @ 13.8Vdc

Housing & Dimensions 19” 1 RU rack mount, 483 x 45 x 410mm Weight 5kg (11lbs.)

Approvals and Certifications

Product Data Sheet Trio QP450

Specifications

(21)

TBURQP4ab-cccdeef represents the part number matrix

Model

Trio Radio QB450

TBURQ Q Data Radios

Code

Select: Unit Type

P Half Duplex Protected Radio - 19” 1RU

Code

Select: Generic Frequency Band

Code

Select: Sub Band - UHF

Code

Select: Hazardous Area Approvals

N No Approval

Code

Select: Modulation

Code

Select: Encryption (subject to country of use)

Code

Select: Licensed Feature

Code

Select: Power Supply

0 10 - 30V DC Standard 1 -48V DC (Option B Only) 3 Dual 110/240V AC (Option B Only)

Code

Select: Hot Standby Options

B Duplicated Tx/Rx Ports D Separate switched Tx & Rx Ports E Common switched Tx/Rx Port

Example: TPURQB4LN-E00E1L0B specifies: Trio QP450 Redundant half duplex radio, 400 to 450MHz, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, three Ethernet & two Serial Ports, 10-30V DC power supply, Duplicated Tx/Rx Ports.

* Export restrictions may apply. Contact your local representative for more details.

** In high ambient temperature situations, the internal fans may operate, resulting in additional current consumption of upto 2 Amps. Note: Not all product features are available in every mode of operation.

Product Data Sheet Trio QP450

Model Code

(22)

Hot Standby Options

B

D

E

RELAY (Coaxial Transmitter Switch)

Tx/Rx Tx/Rx QP450 QP450 Tx/Rx Tx Rx QP450

QP450 - Hot Standby Half Duplex Options

Telemetry & Remote SCADA Solutions

|

www.schneider-electric.com Document Number TBULMxxxxxx-xx

QP450 - Hot Standby Half Duplex Radio - Dimensions

QP450 Hot Standby Option Descriptions Description Antenna Type B Duplicated Tx/Rx Ports Duplicated Tx/Rx _Antennas D Separate Switched Tx _{& Rx Ports} Separate Tx & Rx _Antennas E Common Switched _{Tx/Rx Port} Common Tx/Rx _Antenna