Tooling, Attachments and Accessories

(1)

Corporate Headquarters and Manufacturing Facilities

Hardinge Inc.

In USA, call: 800-843-8801

In Canada, call: 800-468-5946

Elsewhere, call: 607-734-2281

Fax: 607-734-8819

CHNC III and CHNC

IIISP

SUPER-PRECISION

®

CNC Lathes

(2)

CHNC

®

IIISP

Page 2

Diagram Model Page

Key Number Description Number Number

NOTE: Additional tooling available – See pages 4 and 5

IIISP

Page 3

Diagram Model Page

IIISP

Page 4

MISCELLANEOUS TURRET TOP PLATE TOOL HOLDERS AND ACCESSORIES

Photo Model Page

Miscellaneous Tooling

Tools for Turret Top Plates and Vertical Slide

33 Single Tool Holder C9 23

34 Double Tool Holder C10 23

35 Triple Tool Holder C20 23

36 Invertible Tool Holder (Single Block) AHC33 24

37 Invertible Tool Holder (Double Block) AHC34 24

38 Invertible Tool Holder (Triple Block) AHC35 24

39 Quadruple Tool Holder C5 25

40 Universal Tool Post C28 25

41 Boring Tool Holder C19 26

42 Boring Tool Adapter AHC22 26

43 Knurling Tool (Square Shank) — 27

44 Multiple Tool Holder for Vertical Slide AHC6 27

45 Cut-Off Tool Holder for Vertical Slide AHC13 28

46 P3N Cut-Off Blade for Vertical Slide P3N 28

47 Hardinge-Belcar Cut-Off Blade and Inserts G21 29

Miscellaneous Tools, Gages and Accessories

48 Box Tool T12-5_⁄₈_{" & T12-}3_⁄₄_" ₃₀

49 Drill and Turn Tool Holder TH-5_⁄₈_{" & TH-}3_⁄₄_" ₃₀

50 Releasing Acorn Die Holder T10-5_⁄₈_{" & T10-}3_⁄₄_" ₃₁

51 Self-Feeding Die Holder SK11, 12, 21, 22 31

52 Adjustable Tool Setting Gage N2 32

53 Tool Setting Gage Bar — 32

— Vertical Cut-Off Slide — 32

— Tool Touch Probe — 33

— Parts Removal System — 33

— Mist Collector — 34

— Chip Conveyor — 34

— Voltage Transformers — 35

— Collet Closer Foot Switch — 35

— Spindle Reduction Liners — 36

— Spindle Liner Kit — 36

— One-Degree Spindle Orient — 37

— Bar Feed Systems — 37

— Spindle Tooling — 37

46

45

44

43

42

41

40

39

38

37

36

35

34

33

48

49

50

52

51

47

53

(5)

CHNC

®

IIISP

Page 5

Interchangeable Top Plates

Interchangeable Turret Top Plates

Hardinge®_{CHNC Lathes complimented with interchangeable turret top plates have consistently reduced setup time. A wide range of tooling is}

offered for use on the standard 8-station or optional 4-position gang-tooled turret top plates.

The turret top plates are interchangeable, allowing an operator to remove a tooled top plate from a machine and replace it with another pre-tooled top plate to reduce machine setup time. The top plate is secured to the machine by four screws.

The gang-tooled turret top plate is ideal for maximum flexibility when setting up tool configurations. It can accommodate up to six tools per side, reducing the need to index frequently and improving cycle time up to 30%, especially for small parts in the range of 1" (25.40mm) in diameter and under.

Metric top plates: Tool holders must be purchased from manu-facturers other than Hardinge®_.

Part Tool Holders

Number Used

CN-0007214-A 3_⁄₈_{" square and}5_⁄₈_{" round}

CN-0007214-B 1_⁄

2" square and 3⁄4" round

NC-0007214-1S 10mm square and 20mm round CC-0007214-S 12mm square and 25mm round

Part Tool Holders

Number Used

CN-0007214-D1 3_⁄₈_{" square and}5_⁄₈_{" round}

CN-0007214-D 1_⁄₂_{" square and}3_⁄₄_{" round}

All tooling shown is optional. All tooling shown is optional.

8-Station Top Plates

(6)

CHNC

®

IIISP

Page 6

The extension tool holder is generally used for turning operations, but can also be used for holding tools to back-face flanged work, or to cut off, knurl, groove, or thread a workpiece.

The extension tool holder mounts directly into a T-slot of a turret top plate and uses 3_⁄₈_{" or}1_⁄₂_{" square shank}

tool bits for the respective top plate. Each holder features an adjustable wedge for adjusting the tool to center. Round shank tools can be held in these holders by using the AHC22 boring tool adapter.

Extension Tool Holder with Adjustable Shim

The “cut-type” knurling tool is used to cut diamond knurls on a workpiece from 1_⁄₄_{" (6.35mm) to 6"}

(152.40mm) in diameter.

The holder is supplied standard with two “cut-type” knurls (Part Number: ST-0010901-D). The knurls have a 3_⁄₄_{" (19.05mm) OD, a}1_⁄₄_{" (6.35mm) ID, a width of}1_⁄₄_{" (6.35mm), and a 30 diametral pitch.}

The knurls are adjusted by rotating the shaft to which each knurl is mounted. The C30 and CC37 tool holders typically mount into an extension tool holder on 3_⁄

8" and 1⁄2" top plates,

respectively.

“Cut-Type” Diamond Knurling Tool

E F L R S A C

Extension Tool Holders & Cut-Type Knurling Tool

Model Part Dimensions

No. Number A C D E F L M N Q CC13 CC-0008246-01 Inch 1.50 2.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 38.10 69.90 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC14 CC-0008246-02 Inch 2.50 3.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 63.50 95.30 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC15 CC-0008246-03 Inch 3.50 4.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 88.90 120.70 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC16 CC-0008246-04 Inch 4.50 5.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 114.30146.10 38.10 12.70 50.80 44.50 12.70 13.10 15.10 T – T-Bolt W – Washer X – Nut Z1– Set Screw

AH-0007241-L U-0004143 47-0001502-C 0570910

Model Part Dimensions

No. Number A C E F L R S C30 AHB-0010901 Inch 1.63 2.44 .371 1.97 1.69 .380 1.22 mm 41.30 61.90 9.43 50.00 42.90 9.50 31.00 CC37 CCA-0010901 Inch 1.63 2.44 .497 2.25 1.69 .500 1.50 mm 41.30 61.90 12.62 57.20 42.90 12.70 38.10 A D E M N Q WX Z1 C T L F HARDINGE

ELMIRA, N.Y., U.S.A. CC-14

(7)

CHNC

®

IIISP

Page 7

Cut-Off Blades

The cut-off blade is for cutting or parting off material.

It mounts directly into the C31 cut-off tool holder. Each blade is made of high-speed steel and can be resharpened as needed.

Cut-Off Tool Holder

The cut-off holder mounts directly into an extension tool holder to perform cut-off operations from the turret. The cut-off holder comes supplied with a standard P1 1_⁄

16" (1.59mm) wide, high-speed, cut-off

blade. Additional P2 and P3 blades are available in thicknesses of 3_⁄

32" (2.38mm) or 1⁄8" (3.18mm),

respectively.

Cutting from the turret has proven to be easier for holding length dimensions and for controlling the feed rate.

Cut-Off Tool Holder & High Speed Steel Cut-Off Blades

Model Part Dimensions

No. No. C F H S P1 P-0000001 Inch 4.50 .060 .477 .040 mm 114.30 1.50 12.12 .900 P2 P-0000002 Inch 4.50 .090 .477 .070 mm 114.30 2.40 12.12 1.80 P3 P-0000003 Inch 4.50 .130 .477 .100 mm 114.30 3.20 12.12 2.60 A C F L M N R S Y H

No. Number A C F H L M N R S C31 ST-0011209 Inch 1.00 1.47 1.25 .477 1.50 .130 .480 .440 .470 mm 25.40 37.30 31.80 12.12 38.10 3.20 12.20 11.10 11.90 Y – Set Screw 0100520 C F H S

(8)

CHNC

®

IIISP

Page 8

Hardinge-Belcar Cut-Off Insert

The insert mounts directly into the Hardinge-Belcar cut-off tool holders. The inset configura-tion shapes the chips into narrow, easy-flowing coils, allowing heavier feeds and higher spindle speeds compared to conventional cut-off tools. The width of the insert and the diameter of the material determines feedrate and amount of stock removal.

Since there are no wrenches, screws, loose clamps, or springs used, the cutting forces increase the grip of the insert by locking it firmly in place. The insert is easily removed using the extraction tool supplied with each cut-off tool. Inserts are purchased in packages of ten only.

Square Shank Hardinge-Belcar Cut-Off Tool

* Maximum diameter for solid workpieces. Tubing wall thickness may be half of maximum diameter.

The square shank Hardinge-Belcar cut-off tool is used to perform cut-off or grooving operations.

The holder mounts into a square shank tool holder. A light grip is required to place the insert into the holder. The pressure of the first cut seats the insert and holds it tightly in the holder. The insert is removed from the holder using an extractor tool that is supplied as standard. The insert design causes chips to roll inward and form into flowing coils during the cutting operation. This design allows faster feed rates to be used for cut-off operations.

A steady flow of coolant to the cutting edge is recommended.

Right-hand model illustrated.

Hardinge-Belcar Cut-Off Tool & Insert

Model Part Dimensions Hand Insert

No. Number W H L D(Max.)* No.

G16 37A-0009639-02 Inch 3_⁄₈_" 3_⁄₈_" ₂1_⁄₂_" ₁1_⁄₈_" _Right ₂

mm 9.52 9.52 63.50 28.58

G18 50A-0009639-02 Inch 1_⁄

2" 1⁄2" 3" 111⁄16" Right 1

mm 12.70 12.70 76.20 42.86

G19 50A-0009639-03 Inch 1_⁄₂_" 1_⁄₂_" _3" ₁11_⁄₁₆_" _Left ₃

mm 12.70 12.70 76.20 42.86 W W1 D L H

Model Part Dimensions Insert

No. Number W1 Lead No. Hand

.120" 3A-0010903-12 Inch .120 8° 1 Right

mm 3.05

.093" 24A-0010903-09 Inch .093 8° 2 Right

mm 2.36

.120" 3LA-0010903-12 Inch .120 8° 3 Left

(9)

CHNC

®

IIISP

Page 9

Right-Hand and Left-Hand Extension Tool Holder –

1

⁄

2

" Top Plate

The extension holder is used to help balance the tool length in a turret setup, and give additional support for 1_⁄

2" right-hand or left-hand square shank tool bits that overhang the turret. They can

be used for facing, turning, boring, chamfering, or threading operations. The extension holder mounts directly into the machine turret top plate T-slot.

A A C C E E F F L L M M N N P P Q Q T T W W X X _Z1 Z1

Left-Hand and Right-Hand Extension Tool Holder –

3

⁄

8

" Top Plate

The extension holder is used to help balance the tool length in a turret setup and give additional support for 3_⁄

8" left-hand and right-hand square shank tool bits that overhang the turret. They

can be used for facing, turning, boring, chamfering, or threading operations. The extension holder mounts directly into a machine turret top plate T-slot.

A C L Q T W X Z1 E F M N A C L Q T W X Z1 E F M N

Extension Tool Holders

Model Part Dimensions

No. Number A C E F L M N Q

AHC24L AH-0011625-L Inch .910 2.00 .375 1.23 1.50 .500 .520 .590

AHC25R AH-0011626-R mm 23.00 50.80 9.53 31.40 38.10 12.70 13.10 15.10 T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

HP-0007241 U-0004143 47-0001502-C 0570910

No. Number A C E F L M N P Q

CC24L PL-0011625-L Inch .750 2.00 .500 1.25 1.50 .530 .560 .440 .630

CC25R PL-0011625-R MM 19.10 50.80 12.70 31.80 38.10 13.50 14.30 11.10 15.90 T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

(10)

CHNC

®

IIISP

Page 10

Left-Hand and Right-Hand Invertible Extension Tool Holder –

3

⁄

8

" &

1

⁄

2

" Top Plate

The invertible tool holder is used to mount a 3_⁄₈_{" or}1_⁄₂_{" square shank tool for cutting on the rear or front}

of the workpiece. The holder also helps balance the tool length in a turret setup and give additional support for tools that overhang the turret.

The holder mounts into the T-slot of a machine turret top plate. If the cutting tool is to be mounted for cutting on the rear of the workpiece, the tool is inverted and shimmed to place the cutting edge of the tool on the spindle centerline. Adjustable shims AHC36 for 3_⁄

8" tools or CC36 for 1⁄2" tools are required

and purchased seperately. (Adjustable Shims are shown below.)

Adjustable Shim For Invertible Tool Holders

The adjustable shim is used to bring a tool’s cutting edge to the height of the spindle centerline or as a spacer on top of a tool in an invertible tool holder.

The shim is placed in the invertible tool holder under the square shank tool when it is used to cut on the rear of the workpiece.

The thickness of the shim can be adjusted using the three screws built into the holder. The adjustable shim can be set very quickly to the proper thickness by the operator.

F L C E Z1 C C F F A A L L M M N N T T E E Y Y Z1 _Z1 AHC-29 CC-29 AHC-30 CC-30

Invertible Extension Holders & Adjustable Shim

Model Part Dimensions

No. Number A C E F L M N

AHC29 KH-0011625-L Inch .750 1.75 .375 1.23 1.94 .500 .890

AHC30 KH-0011626-R mm 19.10 44.50 9.52 31.30 49.20 12.70 22.60

CC29 CC-0011625-L Inch .750 1.75 .500 1.25 2.00 .500 1.03

CC30 CC-0011626-R mm 19.10 44.50 12.70 31.80 50.80 12.70 26.20 T – Nut Y – Cap Screw Z1_{– Set Screw}

ST-0000374 0101028 AHC29/30 (0570912) & CC29/30 (0570910)

No. Number C E F L CC36 CC-0011760 Inch 1.88 .50 .50 .44 MM 47.60 12.70 12.70 11.20 AHC36 KH-0011760 Inch 1.88 .38 .38 .32 MM 47.60 9.50 9.50 8.00 Z1_{– Set Screw} CC36 (CH-000360) & AHC36 (KH-0010031)

(11)

CHNC

®

IIISP

Page 11

A C E H L P Q T W Z X Z 1

The left-hand drill and shank tool holder is used to hold tooling or other tool holders to perform operations such as center-drilling, drilling, turning, boring, reaming, and tapping.

The holder mounts into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. HDB bushings may be used for holding smaller shank size tools. (See page 16 for HDB bushings.)

Left-Hand Drill and Shank Tool Holder —

1

⁄

2

" Top Plate

Right-Hand Drill and Shank Tool Holder for

3

⁄

8

" and

1

⁄

2

" Top Plates

The right-hand drill and shank tool holder is used to hold tooling or other tool holders to perform operations such as center-drilling, drilling, turning, boring, reaming, and tapping.

The holder is mounted into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

A C E F H L M P Q T W X Z1

Left- & Right-Hand Drill and Shank Tool Holders

Model Part Dimensions

No. Number A C E F H-Bore L M P Q

CC19-5_⁄ 8 PL-0008257-62 Inch .130 1.50 .500 1.50 .625 1.25 1.13 1.06 .750 mm 3.20 38.10 12.70 38.10 15.88 31.80 28.60 27.00 19.10 CC19-3_⁄ 4 PLA-0008257-75 Inch .130 1.50 .500 1.50 .750 1.25 1.13 1.06 .750 mm 3.20 38.10 12.70 38.10 19.05 31.80 28.60 27.00 19.10 T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

PL-0007241 FB-0006906 47-0001502-C 0570906

No. Number A C E F H-Bore L P Q

AHC21 AH-0008257 Inch .130 1.50 .375 1.50 .6253 1.00 .470 .750

mm 3.20 38.10 9.53 38.10 15.883 25.40 11.90 19.10 CC21-5_⁄ 8 PLA-0008256-62 Inch .130 1.50 .500 1.50 .6253 1.13 .440 .750 mm 3.20 38.10 12.70 38.10 15.883 28.60 11.10 19.10 CC21-3_⁄₄ _{PLA-0008256-75 Inch} _.130 _1.50 _.500 _1.50 _{.7503 1.13} _.440 _.750 mm 3.20 38.10 12.70 38.10 19.058 28.60 11.10 19.10 Model No. T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

AHC21 HP-0007241 FB-0006906 47-0001502-C 0570906

CC21-5_⁄₈ _PL-0007241 _FB-0006906 _47-0001502-C _0570906

(12)

CHNC

®

IIISP

Page 12

Center Adjustable Tool Holder

The center adjustable tool holder can be used to perform operations such as center-drilling, reaming, drilling, etc. It is one of the most accurate methods of placing a tool on the spindle centerline.

The holder provides a means for adjusting the center of a tool to its proper relationship to the spindle. After centering the tool, the adjustable portion of the holder is locked into position.

The holder mounts into the T-slot of a turret top plate and has a 5_⁄

8" (15.88mm) diameter bore to hold 5_⁄₈_{" round shank tools. Bushings can be used in the holder to hold tools that are}1_⁄₂_{" or less in diameter.}

(See page 16 for HDB bushings.)

The drill and shank tool holder is used to hold round shank tools to perform operations such as drilling, reaming, turning, boring, and threading.

The holder mounts into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting.

An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

Drill and Shank Tool Holder (Two-Bolt)

F L T A C E G H Q W X Z1 K F E H L T W X A C P Q Z1

Center Adjustable & Drill and Shank (2-Bolt) Tool Holders

Model Part Dimensions

No. Number A C E F G H K L Q

C4 ST-0008249 Inch 1.11 2.47 .375 2.00 .640 .6253 .980 1.11 .630

MM 28.20 62.70 9.53 50.80 16.20 15.883 25.00 28.20 15.90 CC4-5_⁄₈ _PL-0008249 _Inch _1.11 _2.47 _.500 _2.00 _{.640 .6253} _.980 _1.23 _.630

MM 28.20 62.70 12.70 50.80 16.20 15.883 25.00 31.40 15.90 T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

HP-0007241 U-0004143 47-0001502-C 0570906

No. Number A C E F H-Bore L P Q

C18 HPC-0008249 Inch .130 1.50 .375 2.00 .6252 1.00 .440 .750 MM 3.20 38.10 9.53 50.80 15.88 25.40 11.10 19.10 CC18-5_⁄ 8 CC-0008249-62 Inch .130 1.50 .500 2.13 .6252 1.13 .440 .750 MM 3.20 38.10 12.70 54.00 15.88 28.60 11.10 19.10 CC18-3_⁄₄ _{CC-0008249-75 Inch} _.130 _1.50 _.500 _2.13 _{.7502 1.13} _.440 _.750 MM 3.20 38.10 12.70 54.00 19.06 28.60 11.10 19.10 Model No. T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

AHC21 HP-0007241 FB-0006906 47-0001502-C 0570906

CC21-5_⁄₈ _PL-0007241 _U-00004143 _47-0001502-C _0570906

(13)

CHNC

®

IIISP

Page 13

Triple Tool Holder —

3

⁄

8

" and

1

⁄

2

" Top Plates

The triple tool holder is used to hold a maximum of three round shank tools in one tool holder to perform end-working operations such as drilling, boring, turning, reaming and tapping. The triple tool holder is mounted into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. This holder increases tooling versatility and allows for improved production because the top plate does not have to be indexed before performing the next round shank operation.

An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

A C E F G H K L P Q W X Z1 T

Triple Tool Holder

Bushings and tooling not included with this tool holder

Model Part Dimensions

No. Number A C E F G H-Bore K L P Q

CC34-5_⁄₈ _{CC-0008257-62 Inch} _.97 _2.00 _.375 _2.88 _{.659 .6253} _1.09 _1.41 _1.44 _1.59

for 3_⁄₈_{" Top Plate mm 24.60 50.80} _{9.53 73.00 16.73 15.883 27.70 35.70 36.50 40.50}

CC33-3_⁄₄ _{CC-0008257-75 Inch} _.97 _2.00 _.500 _2.88 _{.784 .7503} _1.31 _1.41 _1.44 _1.59

for 1_⁄

2" Top Plate mm 24.60 50.80 12.70 73.00 19.90 19.058 33.30 35.70 36.50 40.50

CC33-5_⁄₈ _CCA-0008257 _Inch _.97 _2.00 _.500 _2.88 _{.659 .6253} _1.31 _1.41 _1.44 _1.59

for 1_⁄₂_{" Top Plate mm 24.60 50.80 12.70 73.00 16.73 15.883 33.30 35.70 36.50 40.50}

T – T-Bolt W – Washer X – Nut Z1_{– Set Screw}

(14)

CHNC

®

IIISP

Page 14

The floating reamer holder is used to align the tool with the hole being reamed. This holder mounts into a round shank tool holder and it floats freely, providing alignment of the reamer with the hole. The holder has a 1_⁄₂_{" (12.70mm) diameter bored}

hole for 1_⁄₂_{" round shank tools and will accept HDB-2 bushings for holding tools with}3_⁄₈_"

and smaller shanks. (See page 16 for HDB bushings.)

A B C D F G H K L Z1

Tool Holder Extension

The tool holder extension is used as a means to position smaller diameter drills on a common plane with other tools in the same setup, reducing tool interference. The tool holder extension mounts directly into a round shank tool holder. It will extend round shank tools an additional 15_⁄₈_{" (41.28mm). (See page 16 for HDB bushings.)}

Drill and bushing not included.

Tool Extension & Floating Reamer Holder

L A B C D G H K Q Z1

Floating Reamer Holder

Model Part Dimensions

No. Number A B C D F G H K L T19-5_⁄ 8 ST-0007967 Inch .840 1.13 1.97 .6243 1.98 .390 .5003 .660 1.00 mm 21.40 28.60 50.00 15.856 50.40 9.90 12.706 16.70 25.40 T19-3_⁄ 4 ST-0007967-01 Inch .840 1.13 1.97 .7493 1.98 .450 .5003 .660 1.00 mm 21.40 28.60 50.00 19.031 50.40 11.50 12.706 16.70 25.40 Z1_{– Set Screw} 0550704

No. Number A B C D G H K L Q TE-5_⁄ 8 ST-0011155 Inch 1.63 1.16 2.78 .6243 .310 .6252 1.25 1.50 .310 mm 41.30 29.40 70.60 15.856 7.90 15.880 31.80 38.10 7.90 TE-3_⁄₄ _{ST-0011155-01 Inch} _1.63 _1.16 _{2.78 .7493} _{.310 .7502} _1.25 _1.50 _.310 mm 41.30 29.40 70.60 19.031 7.90 19.055 31.80 38.10 7.90 Z1_{– Set Screw} 0570906

(15)

CHNC

®

IIISP

Page 15

Adjustable Tool Holder

The adjustable tool holder provides a means of adjusting center working tools such as center drills and drills to the centerline of the spindle. When the tool has been centered, the adjustable portion of the holder is locked into position.

The holder mounts into a round shank tool holder and it has a 1_⁄₂_{" (12.70mm) diameter bore}

to hold round shank tools. HDB-2 bushings can be used in the holder to hold tools with shanks that are 3_⁄

8" or less in diameter. (See next page for HDB bushings.)

A B C D G K W Y F H L Z1

This 1C collet-type tool holder is an accurate method of holding drills, center drills, round shank boring bars, round shank turning tools and reamers.

The T17 holder mounts directly into a round shank tool holder. The holder is hardened and ground and holds standard 1C collets, which have a maximum capacity of 1_⁄₄_{" (6.35mm).}

Turning a nut at the rear of the assembly draws the collet into the assembly, where the matching angles of the collet and the holder cause the collet to close down on the tool. (See Brochure #2351 for 1C collets.)

Drill and 1C collet not included.

C D G M N

1C Collet Holder

Adjustable Tool Holder & 1C Collet Holder

Model Part Dimensions

No. Number A B C D F G H K L

OOD-5_⁄₈ _OO-0007967 _Inch _.840 _1.34 _{2.19 .6245} _1.84 _.375 _{.5002 .690} _1.00

mm 21.40 34.00 55.50 15.862 46.80 9.53 12.705 17.50 25.40 OOD-3_⁄₄ _{OO-0007967-01 Inch} _.840 _1.34 _{2.19 .7500} _1.84 _.375 _{.5002 .690} _1.00

mm 21.40 34.00 55.50 19.050 46.80 9.53 12.705 17.50 25.40 Z1_{– Set Screw}

0550704

No. Number C D G M N T17-5_⁄₈ _37-0000102 _Inch _{1.82 .6243} _.30 _.25 _.54 mm 20.80 15.856 7.60 6.40 13.70 T17-3_⁄ 4 37-000102-01 Inch 1.82 .7493 .30 .25 .54 mm 20.80 19.031 7.60 6.40 13.70

(16)

CHNC

®

IIISP

Page 16

Dimensions

A B

Hardinge Bushing Overall

Style Part Number Figure Diameter Length Type Size Range

1_⁄

2" 3⁄4"

HDB 2 1763-00-19 1 (12.70) (19.05) Fractional 1_⁄

32" to 3⁄8" inclusive by 1⁄64" increments

Kit 0937-00-19 Fractional 23 Bushings from 1_⁄

32" to 3⁄8" by 1⁄64" Incr. 1_⁄ 2" 3⁄4" HDB 2 1763-00-18 1 (12.70) (19.05) Decimal .141", .168", .194", .220", .255", .318", .323", .367", .381" 1_⁄ 2" 3⁄4"

HDB 2 1763-00-17 1 (12.70) (19.05) Metric 1.0mm to 5.0mm inclusive by .2mm increments

1_⁄

2" 3⁄4"

HDB 2 1763-00-16 1 (12.70) (19.05) Letter A to V inclusive

Kit 0937-00-16 Letter 22 Bushings from A thru V

1_⁄

2" 3⁄4"

HDB 2 1763-00-15 1 (12.70) (19.05) Number 1 to 67 inclusive

Kit 0937-00-15 Number 67 Bushings from #1 thru #67

5_⁄

8" 11⁄8"

HDB 5 1765-00-19 1 (15.88) (26.20) Fractional 1_⁄

32" to 1⁄2" by 1⁄64" 5_⁄

8" 11⁄8"

5_⁄

8" 11⁄8"

HDB 5 1765-00-16 1 (15.88) (26.20) Letter A to Z inclusive

Kit 0938-00-16 Letter 26 Bushings from A thru Z

5_⁄

8" 11⁄8"

3_⁄

4" 11⁄8"

HDB 6 1881-00-19 1 (19.05) (28.58) Fractional 1_⁄

16" to 5⁄8" by 1⁄64" 3_⁄

4" 11⁄8"

3_⁄

4" 11⁄8"

HDB 6 1881-00-16 1 (19.05) (28.58) Letter A to Z inclusive

Kit 0939-00-16 Letter 26 Bushings from A thru Z

3_⁄

4" 11⁄8"

NOTE: Millimeters in parentheses.

Toolholder Bushings (HDB2, HDB5 & HDB6)

A

B

(17)

CHNC

®

IIISP

Page 17

Double-Angle Collet Tool Holder

The Double-Angle (DA) Collet Extension Tool Holder mounts directly into a round shank tool holder. The DAH model holders will accept DA200 or DA300 collets (See Brochure #2351 for collets).

Optional qualifying collars and chuck stops are available. The collars position and lock on the holder shank to qualify the tool's position in the DAH holder. Chuck stops are positioned inside the holder body to provide a qualified locating stop for tooling and help to prevent tool “push back”.

Shown with optional collet.

Qualifying Collar Drill Stop

Double-Angle Collet Extension Tool Holder

Collet Model Shank Length Cap Cap Qualifying Collar Drill Stop

Style Number Part Number A B C E Part Number Hex Part Number Part Number

DA300 DAH330 1925-00-00-000000 .500" 2.188" 3.50" .560" 1933-00-00-000000 1_⁄₂_" _{1941-00-00-000000} _{1939-00-00-000000} DA300 DAH350 1927-00-00-000000 .500" 4.188" 5.50" .560" 1933-00-00-000000 1_⁄₂_" _{1941-00-00-000000} _{1939-00-00-000000} DA300 — 7996-03-30-005000 .500" 5.500" 6.79" .560" 7991-03-30-000001 1_⁄₂_" _— _{7990-03-30-000004} DA300 DAH335 1943-00-00-000000 .625" 2.188" 3.50" .680" 1951-00-00-000000 5_⁄ 8" 1957-00-00-000000 1939-00-00-000000 DA300 DAH355 1945-00-00-000000 .625" 4.188" 5.50" .680" 1951-00-00-000000 5_⁄ 8" 1957-00-00-000000 1939-00-00-000000 DA200 DAH255 1959-00-00-000000 .750" 1.875" 3.50" .812" 1967-00-00-000000 11_⁄ 16" 1975-00-00-000000 1973-00-00-000000 DA200 DAH235 1961-00-00-000000 .750" 3.875" 5.50" .812" 1967-00-00-000000 11_⁄₁₆_" _{1975-00-00-000000} _{1973-00-00-000000} DA200 — 7996-03-20-007500 .750" 5.500" 7.23" .860" 7991-03-20-000001 3_⁄₄_" _— _{7990-03-20-000004}

(18)

CHNC

®

IIISP

Page 18

“Crush-Type” Knurling Tool

A B C D F G H K L W X Y 4 5 0 0 30 3 0 Z

“Cut-Type” Straight Knurling Tool

Y

B E

C

D

"Crush- & Cut-Type" Knurling Tools

The knurling tool mounts into a round shank tool holder and comes standard with two knurls. The 64 diametrical pitch knurling wheels are mounted into swivel holders that can be set at any angle to form either diamond or straight knurls. This unit can knurl a workpiece using a cross slide motion (approaching the work perpendicularly), or a turning motion by placing the holder parallel to the workpiece and passing the workpiece between the knurls.

By making the appropriate adjustments, diameters from 5_⁄

32" to 1⁄2" (3.97 to 12.70mm) for

the T8-5_⁄₈_{model and to}3_⁄₄_{" (19.05mm) for the T8-}3_⁄₄_{model can be knurled. A workpiece}

with a diameter of 3_⁄₈_{" (9.53mm) or less can pass through the shank of the knurling tool.}

For stock diameters of 3_⁄₈_{" to}1_⁄₂_{" (9.53 to 12.70mm), the maximum knurling length is}7_⁄₈_"

(22.23mm).

The “cut-type” straight knurling tool is used to generate a straight knurl by cutting the metal.

The tool holder shaft mounts into a 5_⁄₈_{" round shank tool holder and comes standard with}

one knurl. The knurl has a 3_⁄₄_{" (19.05mm) OD and}1_⁄₄_{" (6.35mm) ID with a width of}1_⁄₄_"

(6.35mm).

Model Part Dimensions

No. Number A B C D G H K L Q T8-5_⁄ 8 STA-0010901 Inch 1.63 1.13 2.75 .6243 2.06 .390 .5002 .500 1.00 mm 41.30 28.60 69.90 15.857 52.40 9.90 12.704 12.70 25.40 T8-3_⁄₄ _{STA-0010901-75 Inch} _2.44 _1.49 _{3.93 .7493 2.80} _{.450 .6252 .800} _1.38 mm 61.90 37.90 99.80 19.031 71.00 11.30 15.879 20.30 35.10 W – Washer X – Cutting Wheels Y – Cap Screw Z1_{– Set Screw}

3-0010901 T8-5_⁄

8 (8-0010901) & T8-3⁄4 (ST-0010901) 0100208 0550506

No. Number B C D E

AHC31 KH-0011762 Inch 2.25 2.63 .624 .500

mm 57.20 66.70 15.85 12.70 Y – Cutting Wheels

(19)

CHNC

®

IIISP

Page 19

Revolving Stock Stop

Adjustable Revolving Stock Stop

Adjustable & Revolving Stops

L D

A B

C

A B

L D

The revolving stock stop mounts into a round shank tool holder directly, or with a bushing, to position bar stock in the collet while being fed by a bar feed unit. The front portion of the stop rotates with the workpiece.

The revolving stock stop is used in a round shank tool holder to position bar stock in the collet while being fed by a bar feed unit. The front portion of the stop rotates with the workpiece.

The adjustable stop has a maximum length adjustment of 7_⁄₈_{" (22.23mm).}

Model Part Dimensions

No. Number Min A Max A B D L

T20-5_⁄₈ _RSA-0011157 _Inch _.750 _1.63 _1.13 _.624 _.810

mm 19.10 41.30 28.60 15.85 20.60 T20-3_⁄₄ _{RSA-0011157-01 Inch} _.750 _1.63 _1.13 _.749 _.810

mm 19.10 41.30 28.60 19.03 20.60

No. Number A B C D L

T20-3_⁄₄_{-16 RS-0011157-16 Inch} _1.06 _1.38 _2.44 _.749 _1.44

(20)

CHNC

®

IIISP

Page 20

Interchangeable Bar Pullers & Adapters

Interchangeable Bar Pullers and Adapters

Hardinge®_{bar stock pullers are an economical, accurate way to pull round bar stock}

through a spindle. They are also ideal for using up short pieces of bar stock, or when operating floor space is limited. The pullers are mounted into or round shank tool holder and are stocked in sizes that range from 5_⁄₁₆_{" (7.9mm) to 1}5_⁄₈_{" (41.3mm) in} 1_⁄₁₆_{" (1.59mm) increments. They can be interchanged easily between the three adapter}

shank sizes shown. Overhang from the turret or the face of the round shank tool holder is 311_⁄

16" (93.7mm) for minimal tool interference.

Bar Stock

Puller Adapters

Bar Stock Pullers

Adapter Part Dimensions

No. A B C D F 17170600000000 Inch .810 1.28 2.09 .625 1.75 mm 20.60 32.50 53.10 15.88 44.50 17170500000000 Inch .810 1.28 2.09 .750 1.75 mm 20.60 32.50 53.10 19.05 44.50 Dimensions

Collet Part No.

17170319010625 17170319011250 17170319011875 17170319012500 17170319013125 17170319013750 17170319014375 17170319015000 17170319015625 17170319016250 A B C D F H-Bore Inch 2.88 .63 3.50 1.484-24 1.75 .3125 mm 73.0 15.9 88.9 37.69-24 44.5 7.937 Inch 2.88 .63 3.50 1.484-24 1.75 .3750 mm 73.0 15.9 88.9 37.69-24 44.5 9.525 Inch 2.88 .63 3.50 1.484-24 1.75 .4375 mm 73.0 15.9 88.9 37.69-24 44.5 11.116 Inch 2.88 .63 3.50 1.484-24 1.75 .5000 mm 73.0 15.9 88.9 37.69-24 44.5 12.700 Inch 2.88 .63 3.50 1.484-24 1.75 .5625 mm 73.0 15.9 88.9 37.69-24 44.5 14.288 Inch 2.88 .63 3.50 1.484-24 1.75 .6250 mm 73.0 15.9 88.9 37.69-24 44.5 15.875 Inch 2.88 .63 3.50 1.484-24 1.75 .6875 mm 73.0 15.9 88.9 37.69-24 44.5 17.463 Inch 2.88 .63 3.50 1.484-24 1.75 .7500 mm 73.0 15.9 88.9 37.69-24 44.5 19.05 Inch 2.88 .63 3.50 1.484-24 1.75 .8125 mm 73.0 15.9 88.9 37.69-24 44.5 20.638 Inch 2.88 .63 3.50 1.484-24 1.75 .8750 mm 73.0 15.9 88.9 37.69-24 44.5 22.225 Inch 2.88 .63 3.50 1.484-24 1.75 .9875 mm 73.0 15.9 88.9 37.69-24 44.5 25.083 Inch 2.88 .63 3.50 1.484-24 1.75 1.0000 mm 73.0 15.9 88.9 37.69-24 44.5 25.400 Inch 2.88 .63 3.50 1.484-24 1.75 1.0625 mm 73.0 15.9 88.9 37.69-24 44.5 26.988 Inch 2.88 .63 3.50 1.484-24 1.75 1.1250 mm 73.0 15.9 88.9 37.69-24 44.5 28.575 Inch 2.88 .63 3.50 1.484-24 1.75 1.1875 mm 73.0 15.9 88.9 37.69-24 44.5 30.163 Inch 2.88 .63 3.50 1.484-24 1.75 1.2500 mm 73.0 15.9 88.9 37.69-24 44.5 31.750 Inch 2.88 .63 3.50 1.484-24 1.75 1.3125 mm 73.0 15.9 88.9 37.69-24 44.5 33.338 Inch 2.88 .63 3.50 1.484-24 1.75 1.3750 mm 73.0 15.9 88.9 37.69-24 44.5 34.925 Inch 2.88 .63 3.50 1.484-24 2.13 1.4375 mm 73.0 15.9 88.9 37.69-24 54.0 36.513 Inch 2.88 .63 3.50 1.484-24 2.13 1.5000 mm 73.0 15.9 88.9 37.69-24 54.0 38.1 Inch 2.88 .63 3.50 1.484-24 2.13 1.5625 mm 73.0 15.9 88.9 37.69-24 54.0 39.688 Inch 2.88 .63 3.50 1.484-24 2.13 1.6250 mm 73.0 15.9 88.9 37.69-24 54.0 41.275 17170319003750 17170319003125 17170319004375 17170319005000 17170319005625 17170319006250 17170319006875 17170319007500 17170319008125 17170319008750 17170319009875 17170319010000

Note: Spindle Reduction Liners must be used in the draw tube of the spindle when using Bar Pullers.

(21)

CHNC

®

IIISP

Page 21

Bar Stock Puller

The combination round/square shank bar stock puller is ideal for using up short pieces of bar stock or when operating floor space is limited. The puller is mounted into an invertible square shank tool holder.

• Grips stock up to 15_⁄₈_{" (42mm) diameter — simple screw adjustment}

• Grips round, hex, square and octagon stock with optional caps • Quick set-up time and adjustment

• Grips close to collet — 1_⁄

8" (3.2mm) from face

• Short overhang from the turret top plate for minimal tool interference • Eliminate inventory of feed fingers and pullers

• Self-centering gripper adjustment • Eliminates shock from hydraulic feeders

Capacity - Hex & Square Stock Model Max. Hex/Square Caps C100 19_⁄₃₂_" _One

Note: Spindle Reduction Liners must be used in the draw tube of the spindle when using Bar Pullers.

Spindle Liner Kit – Part Number: HFSS25, HFSS30, HFSS35, HFCC42, HFCC46

Jaw Caps for Hex, Square and Tailstock Work

Shown with optional cap for pulling hex & square stock.

Bar Stock Puller

Puller Jaw Cap Jaw Cap Jaw Caps

Model Part No. Style Required

C100 1821-00-00-000007 Short Models C100 require one long jaw cap.

1821-00-00-000010 Long

No. Number A B C D D1 _E _R

C100 1821-00-00-000000 Inch 1.50 1.00 2.50 2.06 2.16 .750 0 to 1.50 mm 38.10 25.40 63.50 52.40 54.30 19.10 0 to 38.10

Caps Required for Hex/Square Work B E

D C

A D'

(22)

CHNC

®

IIISP

Page 22

Self-Feeding Tap Holder

"Collet-Type" Releasing Tap Holder

Tap and collet not included.

"Collet-Type" Releasing & Self Feeding Tap Holders

A B C D F A B C D F L

The self-feeding tap holder provides automatic thread length control. The tap holder eliminates the need to match feed rate to thread pitch, minimizing tool breakage and “pulled” or “squeezed” threads.

The holder has a 5_⁄

8" shank diameter that allows it to be mounted into a round shank tool holder.

Thread length is controlled internally with an adjusting ring in .01" (.25mm) increments. A driver is used in the holder to accommodate the square of the tap shank, providing a positive drive. A collet is used to centralize and hold the tap in the holder. Tap holders are supplied standard with the necessary collets and drivers. Replacement tap collets and drivers are sold separately. The same unit is used for left- and right-hand taps. The GK11 and GK12 models include three tap collets and four drivers. The GK21 and GK22 include six tap collets and six drivers.

The collet-type releasing tap holder is used to provide thread length control on either right-or left-hand taps by switching a lever inside the body of the tap holder.

The tap holder mounts directly into a round shank tool holder. “TT” style tap holder collets are used to accurately hold and center taps. To provide a positive drive for the taps, the collets have a square slot in the back to accommodate the square of the top shank and a notch in the back bearing of the collet that fits over a hardened pin in the bottom of the holder. (See Brochure #2351 for “TT” tap holder collets.)

* Collets and Drivers furnished with Tap Holder

Model Part Dimensions

No. Number A B C D F TT-5_⁄₈ _STA-0011202 _Inch _2.22 _1.25 _3.47 _.624 _1.63 mm 56.40 31.80 88.10 15.85 41.30 TT-3_⁄₄ _{STA-0011202-01 Inch} _2.22 _1.25 _3.47 _.749 _1.63 mm 56.40 31.80 88.10 19.03 41.30 Maximum Model Maximum Thread Length

No. Tap Size Adjustment GK11 1_⁄₄_{" (6.35mm)} 25_⁄₃₂_{" (19.84mm)}

GK12 1_⁄₄_{" (6.35mm)} 19_⁄₃₂_{" (15.08mm)}

GK21 9_⁄₁₆_{" (14.29mm)} 27_⁄₃₂_{" (21.43mm)}

GK22 9_⁄

16" (14.29mm) 19⁄32" (15.08mm)

No. Number A B C D F L GK11 K11-0011202-K Inch 2.17 1.25 3.42 .625 1.58 .770 mm 55.10 31.80 86.90 15.88 40.10 19.60 GK12 S12-0011202-K Inch 1.89 1.25 3.14 .625 1.58 .770 mm 48.00 31.80 79.80 15.88 40.10 19.60 GK21 K21-0011202-K Inch 2.17 1.25 3.42 .625 1.58 .770 mm 55.10 31.80 86.90 15.88 40.10 19.60 GK12 S22-0011202-K Inch 1.89 1.25 3.14 .625 1.58 .770 mm 48.00 31.80 79.80 15.88 40.10 19.60

Model Tap Size Shank Collet Tap Diver Collet/Driver No. Eng. Metric Dia No. Sq. No. Part No.

GK11/12 6 1.6 .141 4-3.5 .110 2.8 1T0011831C1*/D1* GK11/12 8 4 .168 5-4 .131 3.55 1T0011831C2*/D2* GK11/12 10 4.5-5 .194 5-4 .152 4 1T0011831C2*/D2* GK11/12 12 — .220 6.5-5.5 .165 4 1T0011831C3*/D3* GK11/12 14 6 .255 6.5-5.5 .191 5 1T0011831C3*/D4* GK11/12 1_⁄ 4" — .255 6.5-5.5 .191 5 1T0011831C3*/D4* GK21/22 8 4 .168 5-4 .131 3.55 2T0011831C1*/D1* GK21/22 10 4.5-5 .194 5-4 .152 4 2T0011831C2*/D2* GK21/22 12 — .220 6-5 .165 4 2T0011831C2*/D2* GK21/22 14 6 .255 7-6 .191 5 2T0011831C3*/D3* GK21/22 1_⁄ 4" 6.3 .255 7-6 .191 5 2T0011831C3*/D3* GK21/22 5_⁄ 16" 7-8 .318 9-8 .238 6.3 2T0011831C4*/D4* GK21/22 3_⁄ 8" 10 .381 10-9 .286 7.1 2T0011831C5*/D6* GK21/22 7_⁄ 16" — .323 9-8 .242 6.3 2T0011831C4*/D4* GK21/22 1_⁄ 2" 12-12.5 .367 10-9 .274 7.1 2T0011831C5*/D6* GK21/22 9_⁄ 16" 14 .429 11-10 .322 8 2T0011831C6/D7*

(23)

CHNC

®

IIISP

Page 23

Single, Double & Triple Tool Holders

C20 (Triple)

C10 (Double) C9 (Single)

The single, double, and triple tool holders are used to hold 3_⁄₈_{" square shank tool bits.}

The holder mounts into the T-slot of a top plate and tools are held in place with set screws. These tools are not intended to hold an inverted tool. (See next page for invertible tool holders.)

A B C E R S U F L M N Q Z1

Single, Double & Triple Tool Holders

Model Part Dimensions

No. Number A B C E F L M N Q R S U C9 OL-0007215 Inch .860 .340 1.00 .375 1.00 1.50 .440 .560 .280 .300 .690 .380 mm 21.80 8.70 25.40 9.53 25.40 38.10 11.10 14.30 7.10 7.50 17.50 9.50 C10 OL-0007216 Inch .860 .340 1.00 .375 1.63 1.50 .880 .560 .310 .300 .690 .380 mm 21.80 8.70 25.40 9.53 41.30 38.10 22.20 14.30 7.90 7.50 17.50 9.50 C20 HP-0008243 Inch .860 .340 1.00 .375 2.13 1.50 1.38 .560 .310 .300 .690 .380 mm 21.80 8.70 25.40 9.53 54.00 38.10 34.90 14.30 7.90 7.50 17.50 9.50 Z1_{– Set Screw} 0550910

(24)

CHNC

®

IIISP

Page 24

Invertible Tool Holders

The invertible tool holder is used to hold 3_⁄₈_{" square shank tool bits for cutting on the front or rear of}

a workpiece. One, two or three tool bits can be held, depending on the holder used.

The holders mount into the T-slot of a 3_⁄₈_{" top plate only. If the cutting tool is to be mounted for cutting}

on the rear of the workpiece, the tool must be inverted and shimmed in the holder using an AHC36 adjustable shim to place the cutting edge of the tool on the spindle centerline. (Shims are purchased seperately. See page 10 for adjustable shim.)

AHC 35 (Triple) AHC 34 (Double) AHC 33 (Single) C E F L M N P R S U V Z1 Q

Invertible Tool Holders

Model Part Dimensions

No. Number C E F L M N P Q R S U V AHC33 KH-0007215-01 Inch 1.00 .375 1.00 1.23 .340 .800 .280 .160 .300 .380 .440 .690 mm 25.40 9.53 25.40 31.40 8.70 20.30 7.10 4.00 7.50 9.50 11.10 17.50 AHC34 KH-0007216-01 Inch 1.50 .375 1.00 1.23 .340 .800 .310 .160 .300 .380 .880 .690 mm 38.10 9.53 25.40 31.40 8.70 20.30 7.90 4.00 7.50 9.50 22.20 17.50 AHC35 KH-0008243-01 Inch 2.00 .375 1.00 1.23 .340 .800 .340 .160 .300 .380 1.31 .690 mm 50.80 9.53 25.40 31.40 8.70 20.30 8.70 4.00 7.50 9.50 33.30 17.50 Z1_{– Set Screw} 0570908

(25)

CHNC

®

IIISP

Page 25

Quadruple Tool Holder

The quadruple tool holder gives the operator greater flexibility positioning tooling on a 3_⁄₈_{" top plate}

The holder is mounted into the T-slot of a turret by using two T-bolts. It can hold up to four 3_⁄ 8" square

shank tools for cutting on the front of the workpiece, or three tools cutting on the front and one inverted tool cutting on the rear of the workpiece. The tools are held in the holder with set screws.

Note: For centering inverted tools, a shim is required. The AHC36 adjustable shim shown on page 10 can be used and is purchased seperately.

A C E F L M N Q S T U V Y Z 1 HARDINGE C-5 HARDINGE C-5

Universal Tool Post

The universal tool post mounts in the T-slots on a 3_⁄₈_{" top plate, allowing the operator to position a}

cutting tool to a desired angle.

The holder uses 3_⁄₈_{" square shank tool bits, and up to two tools can be held at one time. The use of shims}

may be necessary to center the tool.

The post can hold two tools in the following combination by repositioning the spacers: both tools right side up, both tools inverted, one tool right side up, and one tool inverted.

R W T R R L X G F P

Quadruple Tool Holder & Universal Tool Post

Model Part Dimensions

No. Number A C E F L M N Q S U V

C5 ST-0011204 Inch 1.44 1.00 .375 2.91 1.81 1.44 .500 .530 .380 .560 .880

mm 36.50 25.40 9.53 73.80 46.00 36.50 12.70 13.50 9.53 14.30 22.20

T – Nut Y – Cap Screw Z1_{– Set Screw}

ST-0000374 0101032 0550910

No. Number F G L P R

C28 ST-0009644 Inch 1.23 .39 1.10 .25 .368

mm 31.4 9.9 28.0 6.4 9.35

T – T-Bolt W – Washer X – Nut

(26)

CHNC

®

IIISP

Page 26

Boring Tool Holder & Adapter

The boring tool adapter converts 3_⁄₈_{" and}1_⁄₂_{" square shank extension tool holders for holding}5_⁄₈_"

round shank tooling.

The adapter mounts into the slot of an extension tool holder. Two set screws hold the round shank tool securely.

HDB5 bushings can be used for holding tools that are 1_⁄

2" in diameter or less. (See page 16 for HDB

bushings.)

Boring Tool Adapter

Z1 F P A B C E H L Q

Boring Tool Holder –

3

⁄

8

" Top Plates

The boring tool holder is used to perform operations such as turning and boring. The holder mounts into the T-slot of a turret and uses 5_⁄

8" round shank tooling. This holder does

not have a lip and can be pivoted to obtain the proper geometry between the cutting tool and the workpiece.

HDB5 bushings can be used for holding tools that are 1_⁄

2" or less in diameter. (See page 16 for

HDB bushings.) C E F H L Q T W X Z1 P

Model Part Dimensions

No. Number C E F H L P Q

C19 HPB-0008257 Inch 1.38 .375 1.50 .625 1.00 .690 .470

mm 34.90 9.52 38.10 15.88 25.40 17.50 11.90 T - T-Bolt W - Washer X - Nut Z1 - Set Screw

HP-0007241 U-0004143 47-0001502-C 0570906

No. Number A B C E F H L P Q

AHC22 AH-0011519 Inch .880 1.38 2.25 .375 1.25 .625 1.25 .630 .500

mm 22.20 34.90 57.20 9.53 31.80 15.88 31.80 15.90 12.70 Z1_{– Set Screw}

(27)

CHNC

®

IIISP

Page 27

This knurling tool mounts directly into the tool slot of an invertible tool holder. The knurl head and shank feature a dovetail configuration which allows the head to be set to the centerline of the spindle.

To position the knurls “on center” with the spindle centerline, the head is adjusted by a simple adjustment of the socket head cap screw located in the tool’s shank. Knurl range is from 1_⁄

8" to 11⁄8" (3.20mm to 28.60mm).

Knurling Tool

The vertical slide multiple tool holder is used to perform operations such as forming, grooving, or chamfering. This holder will hold a maximum of three 3_⁄

8" square shank tools at one time.

The multiple tool holder mounts directly onto the vertical slide, with no machining necessary for installation. Using the vertical slide with a multiple holder provides an additional machining station for the machine.

Multiple Tool Holder for Vertical Slide

F L R S U C M N P Q Z 1

Knurling Tool & Multiple Tool Holder

Model Part Dimensions

No. Number A B C D F

KO75 1827-00-00-000000 Inch 1.50 .750 2.50 2.06 .656 mm 38.10 19.05 63.50 52.40 16.66

No. Number C F L M N P Q R S U

AHC6 AH-0011339-S Inch 1.75 20.6 3.38 1.31 .440 1.13 .250 1.75 1.06 1.00

mm 44.50 52.40 85.70 33.30 11.10 28.60 6.40 44.50 27.00 25.40 Z1_{– Set Screw}

(28)

CHNC

®

IIISP

Page 28

Cut-Off Tool Holder & Blade

Cut-Off Tool Holder for Vertical Slide

The vertical slide cut-off holder is used as an alternative means of cutting off in order to free a turret station to perform forming and turning operations.

The holder mounts directly into the machine’s vertical slide without additional machining for installation. The cut-off holder is supplied with one P3N 3_⁄₃₂_{" (2.38mm) wide, high-speed,}

cut-off blade, shown below. The Hardinge®_{-Belcar carbide insert cut-off blade, shown on the next}

page, can be used in place of the blade supplied.

The cut-off blade is locked in the holder using two eccentric screws. The feed and length of travel are operated by hydraulics and can be adjusted by the operator. Travel of the vertical slide is controlled by using a stop screw.

Model Part Dimensions

No. Number A B C F M N P Q R S U V

AHC13 AH-0009724-01 Inch .590 .310 4.19 2.00 2.31 1.66 .340 1.94 1.44 .630 .810 1.94 mm 15.00 7.90 106.40 50.80 58.70 42.10 8.70 49.20 36.50 15.90 20.60 49.20

W – Washer Y– Bolt Z1_{– Set Screw}

AD-0001067 VD-0011903 0100510 A WY B C F M N P Q R S U V Z1 B

Cut-Off Blade

The cut-off blade is for cutting or parting off material.

It mounts directly into the cut-off tool holder for the vertical slide. The blade is made of high-speed steel and can be resharpened as needed.

C

H

S

Model Part Dimensions

No. Number C F L S

P3N VC-0009639 Inch 5.00 .090 .675 .080

(29)

CHNC

®

IIISP

Page 29

Hardinge-Belcar Cut-Off Insert

The insert mounts directly into the Hardinge-Belcar G21 blade shown above. The inset configuration shapes the chips into narrow, easy-flowing coils, allowing heavier feeds and higher spindle speeds compared to conventional cut-off tools. The width of the insert and the diameter of the material determines feedrate and amount of stock removal. Since there are no wrenches, screws, loose clamps, or springs used, the cutting forces increase the grip of the insert by locking it firmly in place. The insert is easily removed using the extraction tool supplied with each cut-off tool. Inserts are available in packages of ten.

Cut-Off Blade & Insert

The Hardinge-Belcar adjustable blade is used to perform cut-off operations.

It is an insert cut-off tool that mounts directly into a cut-off tool holder. The blade uses a general purpose grade carbide insert. The insert is mounted into the cut-off tool using a press fit. It is removed by using the extractor tool that is supplied with the blade.

The insert design causes chips to roll inward and form into flowing coils during cut-off operations. The design also allows faster feed rates to be used. See below for inserts. A steady flow of coolant to the cutting edge is recommended.

Hardinge-Belcar Cut-Off Blade

H L H₁ W D W₁

* Maximum diameter for solid workpieces. Tubing wall thickness may be half of maximum diameter.

Model Part Dimensions Insert

No. Number W H=H1 L D(Max.)* No.

G21 68A-0009639-03 Inch .088 .6875 4.375 2.375 1,2 or 3

mm 22.35 17.46 111.13 60.30

Model Part Dimensions Insert

No. Number W1 Lead No. Hand

.120" 3A-0010903-12 Inch .120 8° 1 Right

mm 3.05

.093" 24A-0010903-09 Inch .093 8° 2 Right

mm 2.36

.120" 3LA-0010903-12 Inch .120 8° 3 Left

(30)

CHNC

®

IIISP

Page 30

Drill and Turn Tool Holder

D A C F G K L H H Z1

The drill and turn tool holder allows drilling and turning to be done in one operation. Other possible operations include using a stock stop and center drill.

The drill and turn holder mounts directly into a round shank tool holder. Both the 5_⁄₈_{" shank and}

the 3_⁄₄_{" shank holders have two}5_⁄₈_{" (15.86mm) bores which can hold up to two tools. HDB}

bushings may be used for small diameter tools. (See page 16 for HDB bushings.)

Model Part Dimensions

No. Number A C D F G H K L TH-5_⁄₈ _ST-0011213 _Inch _1.19 _2.31 _.624 _1.19 _.410 _.625 _1.00 _2.44 mm 30.20 58.70 15.86 30.20 10.30 15.88 25.40 61.90 TH-3_⁄ 4 ST-0011213-01 Inch 1.19 2.31 .749 1.19 .410 .625 1.00 2.44 mm 30.20 58.70 19.03 30.20 10.30 15.88 25.40 61.90 Z1_{– Set Screw} 0570904

Box Tool

Box Tool & Drill and Turn Tool Holder

The box tool is used to support a workpiece so it cannot deflect from the cutting tool. The box tool mounts directly into a round shank tool holder and is used to turn a single diameter. Model T12-5_⁄₈_{is furnished with one}5_⁄₁₆_{" (7.94mm) square, high-speed tool bit.}

The maximum workpiece diameter that can be turned is 1_⁄₂_{" (12.7mm). Model}

T12-3_⁄₄_{is furnished with one}3_⁄₈_{" (9.53mm) tool bit. The maximum workpiece diameter that}

can be turned is 7_⁄

8" (22.25mm).

There is a hole through the box tool’s shank which allows a part to pass through the shank while it is being turned.

Model Part Dimensions

No. Number A B C D E F G H K L T12-5_⁄₈ _T12-0000625 _Inch _1.38 _1.28 _2.75 _.625 _.500 _1.94 _.380 _.810 _.810 _1.94 mm 34.90 32.50 69.90 15.88 12.70 49.20 9.50 20.64 20.64 49.20 T12-3_⁄ 4 T12-0000625-75 Inch 1.88 1.50 3.75 .750 .880 2.75 .500 1.38 1.19 2.90 mm 47.60 38.10 95.30 19.05 22.20 69.90 12.70 34.90 30.20 73.00

(31)

CHNC

®

IIISP

Page 31

Self-Feeding Die Holder

A B C D F L H K

Releasing Acorn Die Holder

A B

C

D F H

K

Releasing & Self-Feeding Die Holders

The self-feeding die holder provides automatic thread length control. The die holder eliminates the need to match feed rate to thread pitch, minimizing tool breakage and “pulled” or “squeezed” threads.

The holder has a 5_⁄₈_{" shank diameter for mounting into a round shank tool holder. Thread}

length, controlled by the die holder, is adjustable in increments of .01" (.25mm). The same unit is used for both left- and right-hand dies.

Holders SK11, SK12 accept button dies having an OD of 5_⁄₈_",13_⁄₁₆_{", or 1". Adapters are supplied}

standard for the 5_⁄

8" and 13⁄16" sizes while the 1" size mounts directly in the holder. Holders SK21,

SK22 accept button dies having an OD of 13_⁄

16", 1", 15⁄16", or 11⁄2". Adapter rings are supplied

standard for holding the button dies with OD's of 1" or smaller. The 11_⁄₂_{" size mounts directly in the holder.}

The acorn die holder is used to put external threads on a workpiece.

The holder mounts into a round shank tool holder and is generally used for external production threading. The threading capacity of the unit is 1_⁄₄_{" (6.35mm) to}5_⁄₁₆_{" (7.94mm) and uses a No.}

2 die. The maximum thread length is approximately 15_⁄₈_{" (41.28mm).}

The holder is designed to release quickly at the end of the turret travel. The machine spindle must be reversed to feed the die off the workpiece.

Model Part Dimensions

No. Number A B C D F H K L SK11 K11-0011764-K Inch 2.22 1.25 3.47 .625 1.58 .361 1.33 1.26 mm 56.40 31.80 88

Tooling, Attachments and Accessories

Hardinge Inc.

Diagram Model Page

Table of Contents

3⁄8" & 1⁄2" Turret Top Plate Tooling

IIISP

Diagram Model Page

Table of Contents

IIISP

Photo Model Page

Miscellaneous Tooling

Tools for Turret Top Plates and Vertical Slide

Miscellaneous Tools, Gages and Accessories

IIISP

Part Tool Holders

IIISP

Extension Tool Holder with Adjustable Shim

“Cut-Type” Diamond Knurling Tool

Model Part Dimensions

IIISP

Cut-Off Tool Holder & High Speed Steel Cut-Off Blades

Model Part Dimensions

IIISP

Square Shank Hardinge-Belcar Cut-Off Tool

Hardinge-Belcar Cut-Off Tool & Insert

Model Part Dimensions Hand Insert

IIISP

Left-Hand and Right-Hand Extension Tool Holder –

Extension Tool Holders

Model Part Dimensions

IIISP

Adjustable Shim For Invertible Tool Holders

Invertible Extension Holders & Adjustable Shim

Model Part Dimensions

IIISP

" Top Plate

Left- & Right-Hand Drill and Shank Tool Holders

Model Part Dimensions

IIISP

Drill and Shank Tool Holder (Two-Bolt)

Model Part Dimensions

IIISP

Triple Tool Holder

Model Part Dimensions

IIISP

Tool Holder Extension

Floating Reamer Holder

Model Part Dimensions

IIISP

1C Collet Holder

Model Part Dimensions

IIISP

Dimensions

NOTE: Millimeters in parentheses.

Toolholder Bushings (HDB2, HDB5 & HDB6)

Qualifying Collar Drill Stop

Double-Angle Collet Extension Tool Holder

Collet Model Shank Length Cap Cap Qualifying Collar Drill Stop

IIISP

Model Part Dimensions

IIISP

Model Part Dimensions

IIISP

Bar Stock

Adapter Part Dimensions

IIISP

Note: Spindle Reduction Liners must be used in the draw tube of the spindle when using Bar Pullers.

Bar Stock Puller

Puller Jaw Cap Jaw Cap Jaw Caps

IIISP

Model Part Dimensions

IIISP

Single, Double & Triple Tool Holders

Model Part Dimensions

IIISP

Invertible Tool Holders

Model Part Dimensions

IIISP

A C E F L M N Q S T U V Y Z 1 HARDINGE C-5 HARDINGE C-5

Universal Tool Post