For fabric graphics or solid fabric panel
installation onto EZ6 or EZ12 truss.
EZ-BNRCLP
Banner Clip
Rigid strips are sewn into the top and bottom ends of the banner.
Fold the top of the banner over once, so the strip is surrounded
by fabric.
Slide the turned edge of the banner down into the hook end of
the clip, about every two feet, then attach clips onto truss tube.
Alternately, you can attach the clips to the truss first, with the
hook end facing out, then firmly insert graphic into clip.
Repeat with bottom edge, only upside down.
Banner Clip Installation
Your exhibit drawing shows whether to attach the clips onto the top or bottom truss tube.
Graphics may be on either side of a banner. The top seam will determine which side faces you.
Mount bracket to truss, using the horizontal or vertical bracket provided for your application.
Swivel the frame so it’s facing the direction desired for your screen, and tighten top bolt to secure.
Attach crossbar and plastic spacer at choice of holes on frame, and tighten securely with wingnuts.
Mount J-clips to your monitor in the top two mounting holes using the bolts supplied by your
monitor manufacturer.
Hang J-clips onto crossbar and tighten with provided thumbscrew to secure.
Fits 75-200mm width hole patternWorks with most plasmas & LCD’s smaller than 40"
Instructions for mounting and installation
Works with all Trussworks systems.
Instructions for mounting and installation
Works with all Trussworks systems.
Mount bracket to truss, using the horizontal or vertical bracket provided for your application.
Swivel the frame so it’s “feet” are facing the direction desired for your screen, and tighten top
bolt to secure.
Adjust height of crossbar at choice of hole sets on frame, and tighten securely with wingnuts.
Mount J-clips to your monitor in the top two mounting holes using the bolts supplied by your
monitor manufacturer.
Adjust crossbar extenders to the proper width for your monitor and tighten thumbscrews.
Hang J-clips onto crossbar and tighten with provided thumbscrew to secure.
Large Flat Screen Mount
Fits 200-400mm width hole pattern Works with most plasmas & LCD’s 37” or larger
Stand both side frames up as shown
and insert front spacer as shown
Attach rear frame to side
frames with wingnuts
Apply back panel to the
inside of the rear frame.
Apply front panel by putting a slight bend in the panel and applying to the front of the unit.
Place counter top on unit. Be sure to alaign location pins
into lower frame.
EZ6 Oval Designer Counter Assembly Instructions
1. Bolt 2 - A3s to the EZ6 Designer Feet using 2 carriage bolts with wingnuts for each. 2. Stand them up and install the R2s between them at top and bottom using a corner bracket
on each end.
3. Attach the counter top using the supplied brackets and wingnuts. 4. Lay the lower shelf on the lower R2 truss.
5. Install the shelf brackets at the halfway point and put the second shelf on them. 6. Magnet the graphic to the front.
Stand the 2 side units
apart as shown and extend
the panel frames out as shown
Swivel the cross braces into
place and secure them as shown
Insert the shelf
Attach the rear panel to
the back side of the counter
(the side with the velcro strips
top & bottom)
Bend the flaps as shown
and velcro them to the
matching velcro strips on
the counter unit, making
sure to make the seams
as invisible as possible,
also make sure that the
flaps do not interfere with
the door edges
The door has pins located
top and bottom, the pin on top
is longer than the bottom one,
to install tilt the door and insert the
top pin into the frame, then align the
bottom pin and gently
lower the door into position.
Place the counter top in position
it is held in place with velcro.
Construction Detail
EZ6 Designer Reception Counter
1. Bolt 2-A3 pieces to the EZ6 Designer Feet using two carriage bolts
with wingnuts for each.
2. Stand them up and install the A2 between them, at the bottom,
using a corner bracket on each end.
3. Attach the counter top using the supplied brackets and wingnuts.
4. Insert seambar between legs, at the front, 1/2” below the top of leg
(just under the webbing.)
Install the shelf bracket on the middle horizontal webbing, and place
the shelf on.
5. Apply 28.5"H x 24.5"W flexible graphic, using magnet strip on the
reverse perimeter.
Freestanding Counter Setup Instructions
1. Open section with top frame attached 2. Repeat with opposite side. by folding panel frame out from body frame
3. Fold bottom down and lock into opposing 4. Fold top out and lock in place. tabs.
5. Go to the side of the counter with velcro on the top and bottom edges. This is the side that will have the solid panel. Velcro the solid panel into place with the additional velcro showing on the sides.
6. Velcro the flaps to the solid panel vecro edges. Be careful to make the seams as invisible as possible.
7. Repeat procedure on the front, this time velcroing the panels to the frame. Be careful not to get any material beyongd the seam edge. It will interfere with the door.
8. Install the doors with the longer pin up. Locate the holes in the frame and insert the longer pin into hole in the underside of the top frame and then drop in into the hole in the bottom frame.
Repeat with locking door and then velcro on the top. If you are positioning the counter betwee 2 uprights whether as a backwall counter or in the open, we have included 2 small tubes with velcro, you may use these by inserting between the truss tubes and velcroing them to the counter side. This will prevent the counter from moving separate from the truss.
UF4825 CASE
49.5" X 27" X 12-16" OD 48" X 24" X 8-12" ID 30 lbs empty, 80-150 lbs full
(Average weight is 115 lbs)
Stackable 6 high, Rollable and UPS shippable (oversize charges may apply) 4 cases fit on a skid 50" X 48" X 54" @ about 500 lbs
Holds:
2 Packstuff Chairs & 1 Table or 4 Slingback Chairs or Stools or 3 Curved Back Chairs or Stools.
8 EZ6-A4 6 EZ6-R5 6 EZ6-R1 4 EZ612-A4 3 EZ12-A8
UF4848 TUB
51" X 51" X 32" OD 48" X 48" X 28" IDStackable 4 high, Freight shipping only 90 lbs empty, 400-600 lbs full
(Average weight is 500 lbs for EZ6, 400 lbs for EZ612 & 600 lbs for EZ12) Holds: 32 EZ6-A4 32 EZ6-R5 24 EZ6-R1 16 EZ612-A4 14 EZ12-A8
