SECTION 1 - IDENTIFICATION
Vapor Phase Storage Oil ISO 150 Product Name:
Product Code(s): VP150-Q, VP150-G, VP150-P, VP150-D, VP150-T
Spill, Leak, Fire, Exposure, or Accident Call CHEMTREC Day or Night
Within USA and Canada: 1-800-424-9300 CCN794403 or +1 703-527-3887 (collect calls accepted)
SECTION 2 - HAZARD IDENTIFICATION
GHS Hazards
H305 May be harmful if swallowed and enters airways H315+H320 Causes skin and eye irritation
H333 May be harmful if inhaled GHS Precautions
P101 If medical advice is needed, have product container or label at hand P102 Keep out of reach of children
P262 Do not get in eyes, on skin, or on clothing P264 Wash hands thoroughly after handling
P270 Do not eat, drink or smoke when using this product P281 Use personal protective equipment as required
P301+P312 IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell P302+P352 IF ON SKIN: Wash with soap and water
P304+P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
P305+P351+P338 IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing
P306+P360 IF ON CLOTHING: Rinse immediately contaminated clothing and skin with plenty of water before removing clothes
P308+P313 IF exposed or concerned: Get medical advice/attention P332+P313 If skin irritation occurs: Get medical advice/attention P370+P380 In case of fire: Evacuate area
P402+P404 Store in a dry place. Store in a closed container
Warning
GHS Signal Word
LENCO HIGH PERFORMANCE LUBRICANTS FZE
Jebel Ali Free Zone, Dubai, United Arab Emirates
Email: [email protected]
Website: www.lenco-hpl.com
MADE IN THE U.S.A.
SECTION 2 - HAZARD IDENTIFICATION
This product is a liquid that is insoluble in water. Direct eye contact may cause temporary irritation. Short-term exposure is not expected to be irritating. Inhalation and ingestion are not anticipated routes of exposure during normal condition of use. The viscous nature may block breathing if inhaled.
The routes of entry are eye, skin, inhalation and ingestion. These are easily prevented by following normal handling procedures.
There are no targeted organs known. There are no known acute toxicity hazards.
Effects of Overexposure:
This product is not listed as a known or suspected carcinogen by IARC, OSHA, ACGIH or the NTP .
SECTION 3 - COMPONENT DATA
Percent CAS No
Chemical Name
Synthetic Base Oil 72623-87-1 50.00 to 60.00 %
Proprietary Additives 40.00 to 50.00 %
Per paragraph (i) of 29 CFR 1910.1200, this formulation is considered a trade secret and specific chemical identity and exact percentage (concentration) of composition may have been withheld. Specific chemical identity and exact
percentage composition will be provided to health professionals, employees, or designated representatives in accordance with applicable provisions of paragraph (i).
SECTION 4 - FIRST AID MEASURES
Inhalation is not an expected route of exposure. If respiratory irritation or distress occurs, remove the employee to fresh air. Contact a physician or other medical professional if irritation or distress persists.
Upon direct eye contact, hold eyelids open and flush with a steady, gentle stream of water for at least 15 minutes . If irritation is due to exposure to mist or vapors, remove the individual to fresh air. If irritation persists, flush the eyes with clean water until the irritation subsides. If symptoms persist, contact a physician.
If skin irritation occurs, wash with soap and water. Contaminated clothing should be removed to prevent prolonged exposure. If symptoms persist, contact a physician.
If small amounts are ingested, first aid measures are not likely to be necessary. If larger amounts are ingested or if symptoms of ingestion occur, dilute stomach contents with two glasses of water or milk . (NOTE: DO NOT give anything by mouth to an unconscious person.) Do not induce vomiting without medical supervision. If vomiting occurs
spontaneously keep airway clear. If symptoms persist, contact a physician.
Page 2 of 5 Vapor Phase Storage Oil ISO 150
SECTION 5 - FIRE FIGHTING MEASURES
Flash Point: 193 C (379 F) Autoignition: N/A
LEL: N/A UEL: N/A
In accordance with guidance, dry chemical, foam, or CO2 fire extinguishers are all acceptable. Note that while water fog extinguishers are also acceptable, do NOT apply a direct stream of water (water jet) onto burning product because it may cause spreading and increase fire intensity.
No known hazardous combustion products. Mostly oxides of carbon.
Emergency responders in the danger area should wear bunker gear and self-contained breathing apparatus for fire beyond incipient stage.
See Section 8 of the MSDS for other PPE to be worn as conditions warrant. Standard fire fighting equipment is adequate.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
IMPORTANT: As with any spill or leak, before responding ensure that you are familiar with the potential hazards and recommendations of the MSDS. Appropriate personal protective equipment must be worn. See Section 8 of the MSDS for PPE recommendations.
Small volumes or residues may be soaked up with absorbents. Spill response materials should be collected for proper disposal.
If possible, safely contain the spill with dikes or other spill response equipment appropriate for petroleum or organic material releases. Take measures to prevent spreading of product. Product is flammable, and will burn. As a precaution eliminate ignition sources. Prevent from entering sewers or waterways. Large volumes may be transferred to an appropriate container for proper disposal.
SECTION 7 - HANDLING AND STORAGE
Keep away from heat. Open product containers slowly to relieve any pressure and open in a well-ventilated area due to possible presence of irritating vapors in the headspace. Reseal containers immediately after use.
As with any industrial chemical, handle the product in a manner that minimizes exposure to practicable levels. Prior to handling, consult Section 8 of this MSDS to evaluate personal protective equipment needs. Follow all other standard industrial hygiene practices.
Product residue in empty containers is flammable. NOTE that excessive heating or cutting of empty containers may create an ignition source sufficient to start a fire and in extreme cases cause an explosion . All safety precautions taken when handling the product should also be taken when handling empty drums and containers.
SECTION 8 - EXPOSURE CONTROLS AND PERSONAL PROTECTION
Chemical Name / CAS No OSHA Exposure Limits ACGIH Exposure Limits Other Exposure Limits 72623-87-1
TWA: 5 mg/m3 as oil mist, if generated
TWA: 5mg/m3 STEL: 10 mg/m3 as oil mist, if generated
----Synthetic Base Oil
TWA: 5 mg/m3 as oil mist, if generated
TWA: 5mg/m3 STEL: 10 mg/m3 as oil mist, if generated
----Proprietary Additives
Normal general ventilation is expected to be adequate. It is recommended that ventilation be designed in all instances to maintain airborne concentrations at the lowest practicable levels. The user may want to refer to 29CFR 1910.1000. Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of mists and/or vapors below the recommended exposure limits.
Standard control methods are adequate.
Personal protective equipment (PPE) should be selected based upon the conditions under which this material is used. A hazard assessment of the work area for PPE requirements should be conducted by a qualified professional pursuant to OSHA regulations.
Contaminated gear should be disposed of in accordance to local, state, and federal regulations.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Appearance Light to Dark Amber
Odor Characterisitc/Mild
Physical State Liquid
Evaporation Rate >0.1
Specific Gravity (SG) 0.870
SECTION 10 - STABILITY AND REACTIVITY
This product is basically stable.
This product is incompatible with strong oxidizing agents.
Thermal decomposition products are dependent on combustion conditions. A complex mixture of airborne solid, liquid, particulates and gasses may evolve when the material burns. Combustion byproducts may include: oxides of carbon, acid gases, and incompletely burned hydrocarbons as fumes and smoke.
SECTION 11 - TOXICOLOGICAL INFORMATION
LC50/LD50 Data Hazard
Acute Toxicity
Oral Unlikely to be harmful > 5000 mg/kg Dermal Unlikely to be harmful > 2000 mg/kg Inhalation Unlikely to be harmful > 5.0 mg/L
Page 4 of 5 Vapor Phase Storage Oil ISO 150
SECTION 12 - ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
This product has not been evaluated for ecotoxicity. As with any chemical, exposure to the environment should be prevented and minimized wherever possible.
ENVIRONMENTAL FATE
The degree of biodegradability and persistence of the product has not been determined.
SECTION 13 - DISPOSAL CONSIDERATIONS
WASTE DISPOSAL:Consider recycling this product. This product, as sold, does not meet the RCRA characteristics of a hazardous waste . Under RCRA, it is the responsibility of the user, at the time of disposal, to determine whether the product meets the RCRA criteria for hazardous waste. Contact a waste disposal company or local authority for advice. Ensure that collection, transport, treatment and disposal of waste product, containers, and rinsed material comply with all applicable laws and regulations. NOTE that use, mixture, processing or contamination of this product may cause the material to be classified as hazardous waste.
CONTAINER DISPOSAL:
Consider the container part of the product.
SECTION 14 - TRANSPORT INFORMATION
HazardClass UN Number
Proper Shipping Name Packing Group
Agency
Not Regulated --
--DOT U.S. Department of Transportation
If shipped by land in a package having a capacity larger than 3,500 gallons, 49 CFR, Part 130 apply.
Not Regulated --
--ICAO/IATA International Civil Aviation Org / International Air Transport Assoc.
U.S. Dot compliance requirements may apply. See 49 CFR 171.22, 23 & 25.
Not Regulated --
--IMDG International Maritime Dangerous Goods
U.S. Dot compliance requirements may apply. See 49 CFR 171.22, 23 & 25.
SECTION 15 - REGULATORY INFORMATION
This product is a stable and non-hazardous.
SECTION 16 - OTHER INFORMATION
Prepared by: Corporate Regulator Compliance Date of Issue: 5/8/2017
Last Revision Date: 5/8/2017
NOTICE: This MSDS produces a good faith representation of information believed to be accurate as of the last revision date. This document does not create any express or implied product warranties . Since conditions of use are beyond the control of LENCO High Performance Lubricants FZE, all risks associated with the product are assumed by the user.