• No results found

SIP Trunk Configuration Guide. using

N/A
N/A
Protected

Academic year: 2021

Share "SIP Trunk Configuration Guide. using"

Copied!
9
0
0

Loading.... (view fulltext now)

Full text

(1)

SIP Trunk Configuration Guide

using

www.cbeyond.com

1-877-441-9783

(2)

Introduction

Configuring Vertical’s TeleniumIP IP PBX for use with Cbeyond’s BeyondVoice with SIPconnect service offers you and your customers significant cost and voice quality benefits. This document illustrates the steps to register the TeleniumIP system with the BeyondVoice with SIPconnect service. It narrowly focuses on this scope and should be used in conjunction with the TeleniumIP Programming Manual.

SIPconnect is an industry standards-based approach to direct IP peering between SIP-enabled IP PBXs and VoIP service provider networks. If you would like more information about the SIPconnect Interface Specification, which was defined by the SIP Forum in their Service Provider to IP PBX Interoperability Task Group, go to

http://www.sipforum.org/sipconnect.

Prerequisites

Installer: Before using this document, it is required that the installer be certified to install Vertical’s Vodavi TeleniumIP system.

System Requirements

Call Processor MFIM/ MFIME / MFIM100 / MFIM300 / MFIM600

4.0Av minimum

SIP Gateway VOIM/VOIM24 4.0Av minimum

Constraints

(3)

3 of 9 July 2007

Cbeyond – SIP Trunk Setup

Telenium IP System Programming

It is recommended that you follow the programming procedures in the order as presented below.

Note: The subscriber numbers shown here are for example purposes. You must configure the service using the telephone numbers and settings provided by your Cbeyond Account Manager.

PGM 111, Btn 19

(4)

PGM 114

Btn 1: CLIP Display - change the value to ON (default is OFF). Btn 2: COLP Display - change the value to ON (default is OFF).

Btn 6: CLI Station Number - Cbeyond refers to it as the "PBX Username". It is typically the ten-digit Main TN billing telephone number.

(5)

5 of 9 July 2007

PGM 126 (Web only)

Registration User ID - Cbeyond refers to it as the "PBX Username". It is typically the ten-digit Main TN billing telephone number followed by the @ symbol and the proxy server name.

Authentication User ID - Authentication ID assigned in SIP Proxy when required for registration. Cbeyond refers to it as the "PBX Username". It is typically the ten-digit Main TN billing telephone number.

Authentication User Password - User password as assigned in SIP Proxy when required for registration. Cbeyond refers to it as "password for digest challenge".

Contact Number - SIP URL or AOR consisting of the user name and the host domain name or IP address ([email protected]). Cbeyond refers to it as the "PBX Username". It is typically the ten-digit Main TN billing telephone number.

Asc Station Number - any station number can be used, but generally it is the Attendant station number.

User ID Register - change the value to Register (default is Provision). User ID Usage - change the value to ON (default is OFF).

(6)

PGM 133 (Web only)

Soft Switch Type - change the value to Normal if it is not already set to Normal (default is Normal).

Proxy Server Address - the SIP trunk subscription carrier will provide this info. Cbeyond refers to it as "proxy server name".

Primary DNS Address - enter your own DNS address unless the SIP trunk subscription carrier specifies otherwise.

Secondary DNS Address - enter your own DNS address unless the SIP trunk subscription carrier specifies otherwise.

Domain - the SIP trunk subscription carrier will provide this info. Cbeyond refers to it as "proxy server name".

Contact Address Domain - change the value to SIP GW Addr if it is not already set to SIP GW Addr (default is SIP GW Addr).

Proxy Registration Timer - this timer is set to 3600 by default. Do not change this value unless the SIP trunk subscription carrier specifies otherwise.

Proxy Server Port - this port is set to 5060 by default. Do not change this value unless the SIP trunk subscription carrier specifies otherwise.

(7)

7 of 9 July 2007

PGM 142, Btn 15

(8)

PGM 143

(9)

9 of 9 July 2007

PGM 201

References

Related documents

Calls from PBX users that are NOT entered further down in the From PBX/SIP Number/User column, will use this trunk line and the main number will be shown to the called party

 Configure a backup proxy server to maintain SIP trunk service if the primary SIP proxy server fails, your ITSP has provided you with backup proxy server configuration

Select the ANI Substitution tab (on the Trunk Accounts/Edit SIP Trunk menu) to configure outgoing caller ID to match the main Covad assigned number on the SIP trunk.. Select

If the Outbound CID field is empty, the number defined in the “Outbound Caller ID” supplied in the trunk configuration will be used as the caller ID for the outbound calls from

If the Outbound CID field is empty, the number defined in the “Outbound Caller ID” supplied in the trunk configuration will be used as the caller ID for the outbound calls from

Select a Service Definition Index number then, enter the following based on the SIP Trunk Provider:.. Registration mode

22 SIP Trunking Service Configuration Guide 21-19-01 : IP Trunk (SIP) Calling Party Number Setup for Extensions. On a per station basis this populates the “SIP Display Info”

20 SIP Trunking Service Configuration Guide 3.12 IP Trunk Calling Party Number Setup. 21-17-01 : IP Trunk (SIP) Calling Party Number Setup