12VDC MAGNETIC
LED DIMMABLE POWER SUPPLIES
SPEC SHEET DIGEST
LTHM-30-DIM
LTHM-50-DIM
LTH-60-DIM
LTHM100-DIM
LTHM200-DIM
LTHM300-DIM
PRODUCT DESCRIPTION
Smallest dimmable Class II hardwire LED dimming magnetic power supply on the market that works with conventional low voltage magnetic wall mount dimmer with on/off switch. Features include high efficiency, excellent load regulation and no wattage de-rating under 100% load. There is no minimum load requirements for this transformer/driver.
PRODUCT SPECIFICATIONS
Construction: Transformer is encapsulated in all metal
construction enclosure. Enclosure temperature should not exceed 70°C (158°F) @ 40°C (104°F) ambient. Wiring compartment has 2 knockouts sized for 3/4” screw cable conductors. Removable cover for wiring compartment is se-cured in place by clips and one screw. Black powder coated.
Electrical: Input and output terminals are terminal block.
Input leads are 20 AWG. Output leads are 16 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Maximum load is 30W. Coil former is double section bobbin. Auto reset.
Dimming: Works with low-voltage magnetic wall dimmer
with on/off switch.
Mounting: Surface mount with front mounting tab. Warranty: 4 years.
Label: ETL listed for indoor and outdoor use.
Catalog Max. Input Output Weight Dimensions
Number Wattage Voltage Voltage L W H
LTHM30-DIM
30W
120V/60Hz
12
VDC
2.0 lb.
6.03”
1.98”
1.43”
For voltage drop - see www.gmlighting.net/voltagedrop.html or consult GM Lighting Product catalog, page 19.
L
H
W
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net
e-mail: gmlightingllc@sbcglobal.net • Specifications subject to change without notice. LTHM30-DIM_100312
Project:
Type:
Location:
Contact Phone:
LED 12VDC MAGNETIC DIMMABLE
50W POWER SUPPLY
by
PRODUCT DESCRIPTION
Smallest dimmable Class II hardwire LED dimming magnetic power supply on the market that works with conventional low voltage magnetic wall mount dimmer with on/off switch. No minimum load (can be fully loaded). Auto reset thermal circuit breaker on the secondary side.
PRODUCT SPECIFICATIONS
Construction: Transformer is encapsulated in all metal
construction enclosure. Enclosure temperature should not exceed 70°C (158°F) @ 40°C (104°F) ambient. Wiring compartment has 2 knockouts. Removable cover for wiring compartment is secured in place by screw. Black powder coated.
Electrical: Thermal class B-130C. Input leads are 20 AWG.
Output leads are 16 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Maximum load is 50W. Coil former is double section bobbin. Auto reset.
Dimming: Works with low-voltage magnetic wall dimmer
with on/off switch.
Mounting: Surface mount with front mounting tab. Warranty: 4 years.
Label: ETL listed for indoor and outdoor use.
Catalog Max. Input Output Input Open Output Weight Dimensions Number Wattage Voltage Voltage Current Circuit Current L W H
LTHM50-DIM
50W 120V/60Hz 12VDC
410mA
12.5V
4A
3.3 lb.
6.06”
2.59”
2.33”
For voltage drop - see www.gmlighting.net/voltagedrop.html or consult GM Lighting Product catalog, page 19.
L
H
W
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net
e-mail: gmlightingllc@sbcglobal.net • Specifications subject to change without notice. LTHM50-DIM_020412
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net Specifications subject to change without notice. LTH-60-DIM_070611
6-15/16” 5-7/8”
9/32”
3-3/4”
3”
PRODUCT DESCRIPTION
LED dimming magnetic power supply that works with con-ventional low voltage magnetic wall mount dimmer with on/ off switch. 12 or 24 VDC output. 120, 240 or 277 VAC input. No minimum load (can be fully loaded). Highest efficiency with auto reset. Not recommended for digital
installations.
PRODUCT SPECIFICATIONS
Construction: Power supply is fully epoxy encapsulated
for long life and to protect against moisture. Full metal en-closure. No external fusing required. Input and output wire color chart on side for easy reference. 2 knock-outs.
Electrical: Output voltage 12 or 24 VDC. Patented short
circuit and overload protection. Limited power source output allows for Class II wiring. Thermal class B-130C. Input leads are 20 AWG. Output leads are 16 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Auto reset.
Dimming: Works with low-voltage magnetic wall dimmer
with on/off switch.
Mounting: Mounting tabs allow direct screw mounting. Label: ETL listed for indoor use. Not rated for outdoor use.
Tested to CAN/CSA C22.2 No. 60950-1-03 and EN 60950-1. RoHs compliant.
Not rated for outdoor use.
Catalog Max. Input Output Weight Dimensions Number Wattage Voltage Voltage L W H
LTH-60-DIM
60W
120V, 240V
12 or
4.11 lbs.
6-15/16”
3”
3-3/4”
or 277VAC / 50 or 60 Hz
24 VDC
Project:
Type:
Location:
Contact Phone:
LED 12VDC MAGNETIC DIMMABLE
100W POWER SUPPLY
by
PRODUCT DESCRIPTION
Class II hardwire LED dimming magnetic power supply that works with conventional low voltage magnetic wall mount dimmer with on/off switch. No minimum load (can be fully loaded). Auto reset thermal circuit breaker on the secondary side.
PRODUCT SPECIFICATIONS
Construction: Transformer is encapsulated in all metal
construction enclosure. Enclosure temperature should not exceed 70°C (158°F) @ 40°C (104°F) ambient. Wiring compartment has 2 knockouts. Removable cover for wiring compartment is secured in place by screw. Black powder coated.
Electrical: Thermal class B-130C. Input leads are 20 AWG.
Output leads are 16 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Maximum load is 100W. Coil former is double section bobbin. Auto reset.
Dimming: Works with low-voltage magnetic wall dimmer
with on/off switch.
Mounting: Surface mount with front mounting tab. Warranty: 4 years.
Label: ETL listed for indoor and outdoor use.
Catalog Max. Input Output Input Open Output Dimensions Number Wattage Voltage Voltage Current Circuit Current Weight L W H
LTHM100-DIM 100W 120V/60Hz 12VDC
898mA 12.5VDC 8.05A
6 lbs.
9.21”
3.11”
2.93”
For voltage drop - see www.gmlighting.net/voltagedrop.html or consult GM Lighting Product catalog, page 19.
L
H
W
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net
e-mail: gmlightingllc@sbcglobal.net • Specifications subject to change without notice.
PRODUCT DESCRIPTION
A hardwire 200VA LED dimming magnetic power supply that works with conventional low voltage magnetic wall mount dimmer with on/off switch. No minimum load (can be fully loaded). Manual reset thermal 14A circuit breaker on the secondary side.
PRODUCT SPECIFICATIONS
Construction: Transformer is encapsulated in all metal
NEMA 3R rated enclosure. Enclosure temperature should not exceed 70°C (158°F) @ 40°C (104°F) ambient. Wiring
compartment has 3 knockouts sized for 3/4 inch screw cable connectors. Wiring compartment cover is hinged with rivets and opens vertically from bottom to top. Black powder coated.
Electrical: Thermal class B-130°C. Input leads are 18
AWG. Output leads are 12 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Maximum load is 200W.
Dimming: Works with all dimmers that provide symmetrical
form of the current under any conditions.
Mounting: Surface mount with back mounting tab. Warranty: 4 years.
Label: UL listed. UL file number: E194005.
Catalog Max. Input Output Input Open Output Dimensions Number Wattage Voltage Voltage Current Circuit Current Weight L W H LTHM200-DIM-24 200W 120V/60Hz 24VDC 0.6A 24VDC 8.05A 9 lbs. 8” 4.1” 3.1”
For voltage drop - see www.gmlighting.net/voltagedrop.html
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net
e-mail: gmlightingllc@sbcglobal.net • Specifications subject to change without notice.
LTHM200-DIM-24_121012
L
H
Project:
Type:
Location:
Contact Phone:
LED 12VDC MAGNETIC DIMMABLE
300W POWER SUPPLY
by
PRODUCT DESCRIPTION
A hardwire LED dimming magnetic power supply that works with conventional low voltage magnetic wall mount
dimmer with on/off switch. No minimum load (can be fully loaded). Manual reset thermal 4A circuit breaker on the primary side.
PRODUCT SPECIFICATIONS
Construction: Transformer is encapsulated in all metal
construction enclosure. Enclosure temperature should not exceed 65°C (149°F) @ 40°C (104°F) ambient. Wiring compartment has 3 knockouts, sized for 3/4” screw cable connectors. Wiring compartment cover hinged with rivets and opens vertically from bottom to top. Black powder coated. Enclosure type: NEMA 3R Outdoor.
Electrical: Thermal class B-130C. Input leads are 18 AWG.
Output leads are 16 AWG. Lead insulation rated to 105°C (221°F). Transformer utilizes a class B 130°C (266°F) insulation system. Maximum load is 300W. Coil former is double section bobbin.
Dimming: Works with low-voltage magnetic wall dimmer
with on/off switch.
Mounting: Surface mount with front mounting tab. Warranty: 4 years.
Label: UL listed for indoor and outdoor use.
Catalog Max. Input Output Input Open Output Dimensions Number Wattage Voltage Voltage Current Circuit Current Weight L W H
LTHM300-DIM 300W 120V/60Hz 12 VDC
0.6A
12.5VDC
25A
9 lbs.
9.0”
4”
3”
For voltage drop - see www.gmlighting.net/voltagedrop.html or consult GM Lighting Product catalog, page 19.
L
H
W
GM Lighting, LLC • 9830 W. 190th St. • Unit F • Mokena, IL 60448 Toll-Free: (866) 671-0811 FAX: (708) 478-2640 • www.gmlighting.net
e-mail: gmlightingllc@sbcglobal.net • Specifications subject to change without notice.
General
This transformer is to be installed in accordance with Article 450 of the
National Electric code. The transformer must be installed in a well-ventilated
area free from explosive gases and vapors. Proper operation requires the
free flow of air. Only a qualified electrician should install this hardwired
transformer.
Precautions Before Installing
Check the label and ensure the transformer has the proper input voltage,
output voltage and wattage for the job. Check the wire markings to ensure
they match the wiring diagram on this instruction sheet.
Mounting
Select a suitable location capable of supporting the weight of the transformer.
Use the two keyholes provided on the mounting flange.
Input Connections/Grounding
Remove the wiring compartment knockouts and install strain reliefs. With
power turned off, route the input wires through a strain relief and connect one
wire to black and one wire to white. For all wire connections use only UL
listed wire nuts and connectors of suitable size and type. The transformer
case MUST be grounded in accordance with the N.E.C. Connect the green
wire transformer to ground.
Output Connections
Bring the 12 volt DC lamp wires through the open knockout and connect the
positive (+) side to the red transformer wires, and negative (-) side to the blue
transformer wires. Connect the 12V DC wire to the red and blue wires.
Connect the red wire to the positive (+) side and the negative (-) wire to the
blue side.
Boost Tap
This transformer is equipped with an optional 10% boost tap which can
compensate for voltage drop between the transformer and the lighting fixture.
If the fixtures are receiving 10.5 Volts or less, we recommend you connect
the boost tap. To use the boost tap, the input wires are connected to the
orange and white wire instead of the black and white wire. Make certain the
black wire is capped with a wire nut if you use the boost tap. Make certain
the orange wire is capped with a wire nut if you do not use the boost tap.
INPUT WIRES WITHOUT BOOST TAP: Black & White
INPUT WIRES WITH BOOST TAP: Orange & White
GROUND WIRE: Green
OUTPUT WIRES: Blue (-) & Red (+)