ENGLISH DIGITAL CAMERA

(1)

Camera User Guide

z Please read the Read This First section (p. 5).

z Please also see the Software Starter Guide and the Direct Print User Guide.

DIGITAL CAMERA Camera U s er Gu ide

ENGLISH

(2)

Flowchart and Reference Guides

This Guide

Shooting with the Camera

Software Starter Guide Installing the Software This Guide

This Guide

Connecting the Camera to a Computer

Software Starter Guide

Direct Print User Guide Printer User Guide

Using the Printer and Printing Downloading Images to a Computer

Use of genuine Canon accessories is recommended.

This product is designed to perform optimally when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis.

(3)

1

Camera Body Temperature

If your camera is used for prolonged periods, the camera body may become warm. Please be aware of this and take care when operating the camera for an extended period.

About the LCD Monitor

The LCD monitor is produced with extremely high-precision manufacturing techniques. More than 99.99% of the pixels operate to specification. Less than 0.01% of the pixels may occasionally misfire or appear as red or black dots.

This has no effect on the recorded image and does not constitute a malfunction.

Language Setting

Please see page 21 to change the language setting.

Please read through the Read This First section (p. 5) before using your camera.

Disclaimer

z While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Canon reserves the right to change the specifications of the hardware and software described herein at any time without prior notice. z No part of this guide may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without the prior written permission of Canon.

z Canon makes no warranties for damages resulting from corrupted or lost data due to a mistaken operation or malfunction of the camera, the software, the CompactFlashTM cards (CF cards), personal computers, peripheral devices, or use of non-Canon CF cards.

(4)

Trademark Acknowledgments

• Canon and PowerShot are trademarks of Canon, Inc.

• CompactFlash is a trademark of SanDisk Corporation.

• iBook and iMac are trademarks of Apple Computer, Inc.

• Macintosh, PowerBook, Power Macintosh and QuickTime are trademarks of Apple Computer, Inc, registered in the United States and other countries.

• Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Other names and products not mentioned above may be registered trademarks or trademarks of their respective companies.

Symbols Used

Icons under title bars show the operations mode. As in the example below, the shooting mode should be set to , , or .

Using the Flash

This mark denotes issues that may affect the camera's operation.

This mark denotes additional topics that complement the basic operating procedures.

(5)

3

Read this First

5

Please Read ...5

Safety Precautions ...6

Preventing Malfunctions ...11

Components Guide

12 Preparing the Camera

15

Installing the Battery and CF Card ... 15

Formatting a CF Card...18

Setting the Date/Time...20

Setting the Language ...21

Basic Functions

23

Turning the Power On/Off... 23

Switching between Shooting/Playback...25

Using the LCD Monitor ... 26

Shooting – The Basics

31

Auto Mode ...31

Reviewing an Image Right After Shooting... 34

Selecting a Shooting Mode...35

Changing the Resolution and Compression ... 36

Using the Flash ...38

Macro/ Infinity Modes ... 40

Self-timer ... 41

Continuous Mode... 41

Shooting Panoramic Images (Stitch Assist) ... 42

Movie Mode ... 45

Playback – The Basics

47

Displaying Images Individually (Single Image Playback) ... 47

Magnifying Images ... 47

Viewing Images in Sets of Nine (Index Playback) ... 48

Jumping between Images ... 49

Viewing/Editing Movies ... 49

Erasing

53

Erasing Single Images ... 53

Erasing All Images ... 53

Shooting – Advanced Functions

54

Selecting Menus and Settings... 54

Menu Settings and Default Settings ... 57

Resetting the Settings to Default... 62

Shooting Problem Subjects for the Autofocus... 63

Switching between Focus Settings... 64

Switching between Light Metering Modes... 65

Adjusting the Exposure ... 65

(6)

Table of Contents

Changing the ISO Speed...69

Changing the Photo Effect...70

Playback – Advanced Functions

72

Rotating Images in the Display...72

Attaching Sound Memos to Images...73

Auto Play ... 74

Protecting Images...75

Various Functions

76

About Printing ... 76

DPOF Print Settings ...78

Image Transmission Settings (DPOF Transfer Order)...82

Downloading Images to a Computer ... 83

Downloading Directly from a CF card... 91

Resetting the File Number...92

Customizing the Camera (My Camera Settings)... 93

Registering My Camera Settings... 94

List of Messages

98 Troubleshooting

100 Appendix

105

Replacing the Date Battery...105

Using the Power Kits (Sold Separately) ...106

Camera Care and Maintenance ...110

Specifications

111

Battery Performance ... 114

CF Cards and Estimated Capacities (Recordable Images)... 114

Photo Tips and Information

117 Index

119

Functions Available in Each Shooting Mode ... 124

(7)

5

Read This First

Please Read

Test Shots

Before you try to photograph important subjects, we highly recommend that you shoot several trial images to confirm that the camera is operating and being operated correctly. Please note that Canon, its subsidiaries and affiliates, and its distributors are not liable for any consequential damages arising from any malfunction of a camera or accessory, including CompactFlashTM cards, that results in the failure of an image to be recorded or to be recorded in a format that is machine readable.

Warning Against Copyright Infringement

Please note that Canon digital cameras are intended for personal use and should never be used in a manner that infringes upon or contravenes international or domestic copyright laws and regulations. Please be advised that in certain cases the copying of images from performances, exhibitions, or commercial properties by means of a camera or other device may contravene copyright or other legal rights even if the image was shot for personal use.

Warranty Limitations

This camera's warranty is only effective in the country of sale. If a problem arises while the camera is in use abroad, please convey it back to the country of sale before proceeding with a warranty claim to a Canon Customer Support Help Desk.

For Canon Customer Support contacts, please see the Canon Limited Warranty supplied with your camera.

(8)

Read This First

Safety Precautions

z Before using the camera, please ensure that you have read and understood the safety precautions described below. Always ensure that the camera is operated correctly.

z The safety precautions noted on the following pages are intended to instruct you in the safe and correct operation of the camera and its accessories to prevent injuries or damage to yourself, other persons and equipment.

z In the next few pages, the term "equipment" refers primarily to the camera, batteries, and separately sold battery and charger kit and compact power adapter.

(9)

7

Read This First

WARNINGS

z Do not aim the camera directly into the sun or at other intense light sources which could damage

your eyesight.

z Do not trigger the flash in close proximity to human or animal eyes. Exposure to the intense light produced by the flash may damage eyesight. In particular, remain at least one meter (39 inches) away from infants when using the flash.

z Store this equipment out of the reach of children and infants. Accidental damage to the camera or batteries by a child could result in serious injury. In addition, placement of the strap around a child's neck could result in asphyxiation.

z Be particularly careful to keep the date battery used in the camera away from children. Seek medical assistance immediately if a child swallows a battery.

z Do not attempt to disassemble or alter any part of the equipment that is not expressly described

in this guide. Disassembly or alteration may result in high-voltage electrical shock. Internal inspections,

alterations and repairs should be conducted by qualified service personnel authorized by your camera distributor or a Canon Customer Support Help Desk.

z To avoid the risk of high-voltage electrical shock, do not touch the flash portion of the camera if it

has been damaged. Similarly, never touch internal portions of the equipment that become exposed as a

result of damage. There is a risk of high-voltage electrical shock. Please take the first opportunity to consult your camera distributor or a Canon Customer Support Help Desk.

z Stop operating the equipment immediately if it emits smoke or noxious fumes. Failure to do so may result in fire or electrical shock. Immediately turn the camera's power off, remove the camera batteries or unplug the power cord from the power outlet. Confirm that smoke or fume emissions have ceased. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

(10)

Read This First

z Stop operating the equipment if it is dropped or the casing is damaged. Failure to do so may result in fire or electrical shock. Immediately turn the camera's power off, remove the camera batteries or unplug the power cord from the power outlet. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

z Do not allow the equipment to come into contact with, or become immersed in, water or other

liquids. Do not allow liquids to enter the interior. The camera has not been waterproofed. If the exterior

comes into contact with liquids or salt air, wipe it dry with a soft, absorbent cloth. In the event that water or other foreign substances enter the interior, immediately turn the camera's power off and remove the camera batteries or unplug the power cord from the power outlet. Continued use of the equipment may result in fire or electrical shock. Please consult your camera distributor or the closest Canon Customer Support Help Desk.

z Do not use substances containing alcohol, benzene, thinners or other flammable substances to

clean or maintain the equipment. The use of these substances may lead to fire.

z Remove the power cord on a regular periodic basis and wipe away the dust and dirt that collects

on the plug, the exterior of the power outlet and the surrounding area. In dusty, humid or greasy

environments, the dust that collects around the plug over long periods of time may become saturated with humidity and short-circuit, leading to fire.

z Do not cut, damage, alter or place heavy items on the power adapter cord. Any of these actions may cause an electrical short circuit, which may lead to fire or electrical shock.

z Do not handle the power cord if your hands are wet. Handling it with wet hands may lead to electrical shock. When unplugging the cord, ensure that you hold the solid portion of the plug. Pulling on the flexible portion of the cord may damage or expose the wire and insulation, creating the potential for fires or electrical shocks.

z Use only the recommended power accessories. Use of power sources not expressly recommended for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards.

(11)

9

Read This First

z Do not place the batteries near a heat source or expose them to direct flame or heat. Neither should you immerse them in water. Such exposure may damage the batteries and lead to the leakage of corrosive liquids, fire, electrical shock, explosion or serious injury.

z Do not attempt to disassemble, alter or apply heat to the batteries. There is serious risk of injury due to an explosion. Immediately flush with water any area of the body, including the eyes and mouth, skin, or clothing that comes into contact with the inner contents of a battery.

z Avoid dropping or subjecting the batteries to severe impacts that could damage the casings. It could lead to leakage and injury.

z Do not short-circuit the battery terminals with metallic objects, such as key holders. It could lead to overheating, burns and other injuries.

z Before you discard a battery, cover the terminals with tape or other insulators to prevent direct

contact with other objects. Contact with the metallic components of other materials in waste containers

may lead to fire or explosions. Discard the batteries in specialized waste facilities if available in your area. z Use only recommended batteries and accessories. Use of batteries not expressly recommended for

this equipment may cause explosions or leaks, resulting in fire, injury and damage to the surroundings. z If using AA-size NiMH batteries, use only Canon AA-size NiMH batteries and the charger

recommended for use with these batteries. Use of another charger may cause batteries to overheat

or deform, posing risk of fire or electric shock.

z Disconnect the battery charger or compact power adapter from both the camera and power outlet

after recharging and when the camera is not in use to avoid fires and other hazards. Continuous

use over a long period may cause a unit to overheat and distort, resulting in fire.

z The camera terminal of the battery charger cord and the compact power cord is designed for

exclusive use with your camera. Do not use it with other products or batteries. There is a risk of fire

(12)

Read This First

CAUTIONS

z Avoid using, placing or storing the equipment in places subject to strong sunlight or high

temperatures, such as the dashboard or trunk (boot) of a car. Exposure to intense sunlight and heat

may cause the batteries to leak, overheat or explode, resulting in fire, burns or other injuries. High temperatures may also cause deformation of the casing. Ensure that there is good ventilation when using the battery charger to charge the batteries or power the camera.

z Do not store the equipment in humid or dusty areas. Storage in such areas could lead to fire, electrical shock or other damage.

z Be careful not to bang the camera or subject it to strong impacts or shocks that could lead to

injury or damage the equipment when wearing or holding it by the strap.

z Be careful not to cover the flash with your fingers or clothing when shooting. The flash may be damaged and emit smoke or noise. In addition, do not touch the surface of the flash after taking several pictures in rapid succession. Either action could result in burns.

z Do not operate the flash with dirt, dust or other items stuck to its lens. The resulting heat build-up could damage the flash.

z Ensure that the battery charger is plugged into a power outlet of the specified rating, not over the

specified rating. The plug of the battery charger varies according to region.

z Do not use the battery charger or compact power adapter if the cable or plug is damaged, or if the

plug is not fully inserted into the power outlet.

z Do not allow metal objects (such as pins or keys) or dirt to contact the charger terminals or plug. z If your camera is used for prolonged periods, the camera body may become warm. Please take

care when operating the camera for an extended period as your hands may experience a burning sensation.

(13)

11

Read This First

Preventing Malfunctions

Avoid Strong Magnetic Fields

Never place the camera in close proximity to electric motors or other equipment generating strong electromagnetic fields. Exposure to strong magnetic fields may cause malfunctions or corrupt image data.

Avoid Condensation Related Problems

Moving the equipment rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its external and internal surfaces. You can avoid this by placing the equipment in an airtight, resealable plastic bag and letting it adjust to temperature changes slowly before removing it from the bag.

If Condensation Forms Inside the Camera

Stop using the camera immediately if you detect condensation.

Continued use may damage the equipment. Remove the CF card and battery or power cord (if connected) from the camera and wait until the moisture evaporates completely before resuming use.

Extended Storage

When not using the camera for extended periods of time, remove the batteries from the camera or battery charger and store the equipment in a safe place. Storing the camera for extended periods with batteries installed will run down the battery and may damage the camera.

(14)

Components Guide

* To connect the camera to a computer or printer, use one of the following cables. • Computer: Interface Cable IFC-400PCU (supplied with the camera)

• Direct Print Compatible Printers (Sold Separately)

• CP Printers: Interface Cable IFC-400PCU (supplied with the camera) or the Direct Interface Cable DIF-100 (supplied with the CP-100/CP-10)

• Bubble Jet Printers:

- Bubble Jet Direct Compatible Printers: Please refer to your Bubble Jet printer user guide. - PictBridge Compliant Printers: Interface Cable IFC-400PCU (supplied with the camera)

• PictBridge Compliant Non-Canon Printers: Interface Cable IFC-400PCU (supplied with the camera)

Please refer to the System Map or the Direct Print User Guide supplied with the camera for direct print compatible printer information.

Shutter Button (p. 31) Shooting Mode Switch (p. 35) Viewfinder Window (p. 32) Microphone (p. 73) AF-assist Beam (p. 33)

Red-eye Reduction Lamp (p. 39) Self-timer Lamp (p. 41) Flash (p. 38) Terminal Cover (p. 86) DIGITAL Terminal* (p. 86) DC IN Terminal (p. 109) Lens Lens Cover (p. 23)

(15)

13

Components Guide

* Be careful when carrying the camera by the strap. Don't swing the camera on the strap, and keep the strap and camera body clear of obstacles.

Date Battery Holder (p. 105) Viewfinder (p. 32) Strap Mount* CF Card Slot/ Battery Cover (p. 15) Speaker Tripod Socket LCD Monitor (p. 26)

(16)

Components Guide

.

FUNC. (Function) (p. 54)/

(Single Image Erase) Button (p. 53)

DISP. (Display) Button (p. 26) MENU Button (p. 55)

SET Button

Omni Selector (p. 38, 40, 41, 65)

(Light Metering)/ , (Flash)/ , (Continuous)

(Self-timer)/ , (Macro)/ (Infinity)/

Zoom Button (p. 31)

Shooting: (Wide Angle)/ (Telephoto) (p. 31)

Playback: (Reduce)/ (Magnify) (p. 47)

(Power/Playback) Button (p. 23) (Print/Share) Button

The following operations are accessible through one easy

press of the button.

- Printing: See the Direct Print User Guide (separate from this guide).

- Downloading images (Windows only): See page 83 of this guide and the Software Starter Guide (separate from this guide). The indicator blinks or lights during a printer or computer connection.

Blue: Ready to Print/Ready to transfer images Blinking Blue: Printing/Transferring

The indicators light or blink when you open the lens cover or whenever you press the shutter button.

Upper Indicator

Green: Ready to shoot or ready to communicate

with your computer.

Blinking Green: Starting-up, recording to the CF

card, reading the CF card, erasing data on the CF card, or transmitting data to your computer.

Orange: Ready to shoot (using the flash).

Blinking Orange: Ready to shoot (camera shake

warning) or charging the flash (with LCD monitor On).

Lower Indicator

Yellow: Macro mode or Infinity mode

Blinking Yellow: Focusing difficulty (although you

can press the shutter button, try using focus lock (p. 63))

(17)

15

Preparing the Camera

Installing the Battery and CF Card

Insert two (2) AA-size alkaline batteries

(included with the camera) or two (2) AA-size

NiMH batteries (sold separately) and insert

the CF card.

1 Close the lens cover and check that

the camera power is off.

2 Slide the CF card slot/battery cover

and open it.

3 Press the battery cover lock towards

the arrow to open the cover.

Battery Cover

Battery Cover Lock

4 Insert the batteries as shown and

close the battery cover.

5 Insert the CF card as shown and

close the CF card slot/battery

cover.

z Slide the CF card firmly to the end (to release the CF card, hold onto it and remove.).

(-) Negative end

(18)

Preparing the Camera

z When the indicator next to the viewfinder blinks green, the camera is writing, reading, erasing, or transmitting an image to or from the CF card. Do not perform the following operations as recorded images may be damaged as a result.

• Turn the camera off

• Open the CF card slot/battery cover • Shake the camera

z You are recommended to use CF cards that have been formatted in your camera (p. 18). The card supplied with the camera may be used without further formatting.

z We recommend that you use the separately sold AC Adapter Kit ACK800 to power the camera during long usage sessions (p. 109).

z The separately sold battery charger kit lets you use rechargeable NiMH batteries to power the camera (p. 106). z See Battery Performance (p. 114).

z For information about the Battery and Charger Kit and AA-size rechargeable NiMH batteries, see the System Map (separate from this guide).

z See CF Cards and Estimated Capacities (Recordable Images) (p. 114).

Proper Battery Handling

z Use AA-size alkaline or Canon AA-size NiMH batteries (sold separately) only. For information on handling the AA-size rechargeable NiMH batteries, see Using the Power Kits (Sold Separately) (p. 106).

z Never use manganese or lithium batteries, as these battery types may overheat in the camera. z Since the performance of alkaline batteries

may differ according to brand, the operating time of the batteries you purchase may not be as long as the batteries that came with the camera.

(19)

17

z Camera operating time may shorten at low temperatures when alkaline batteries are used. Also due to their specifications, alkaline batteries may expire faster than NiMH batteries. If you are using the camera in cold areas or for a long time, we recommend using Canon AA-size NiMH Battery Kit NB4-200 (a 4-battery Kit). z While it is possible to use AA-size

nickel-cadmium batteries, performance is unreliable and their use is not recommended.

z Never mix unused and partially used

batteries. Always load two fresh (or fully recharged) batteries at the same time.

z Be careful to load the batteries with their

positive (+) and negative (-) ends in the right direction.

z Never mix batteries of different types or from

different manufacturers. Both batteries should be identical.

z Before inserting the batteries, wipe the battery terminals well with a dry cloth. Oil from one's skin or other dirt may cause a considerable reduction in the number of recordable images or reduced usage time.

z Battery performance deteriorates at low temperatures (especially with alkaline batteries).

If you are using the camera in cold areas and batteries are running down faster than they should, you may be able to restore performance by placing batteries in an inner pocket to warm them up prior to use. But be careful that you don't put the batteries into a pocket together with a metal key chain or other metallic objects, as these objects may cause batteries to short-circuit. z If you do not plan to use the camera for a long

time, remove the batteries from the camera and store them in a safe place. Batteries may leak and damage the camera if left installed during prolonged periods of non-use.

WARNINGS

Never use damaged batteries or batteries whose outer seal is completely or partially missing or peeled off, as there is risk that such batteries may leak, overheat, or burst. Always check the seals on store-bought batteries before loading them, as some batteries may come with defective seals. Do not use batteries with defective seals.

(20)

Formatting a CF Card

You should always format a CF card when

you wish to use a new one, or when you wish

to delete not only the images in the CF card

but also other data.

Formatting a CF card will permanently erase all data already on it, including all of its protected images. Check the contents before formatting cards that were previously used.

1 Turn the power on (p. 23).

2 Press the MENU

button and select

[

(Set up)] using

or .

Never use batteries that look like this.

Batteries with all or part of the seal (electrical insulation sheath) peeled off.

The positive electrode (plus terminal) is flat.

The negative terminal is correctly formed (protruding from the metal base), but the seal does not extend up over the edge of the metal base.

Battery Status Indications

The LCD monitor displays an icon or message to let you know when batteries are low or depleted.

Batteries are beginning to run low. Replace (or recharge) batteries promptly. If the LCD monitor is off, this icon will appear when you press any of the following buttons: the omni selector, DISP. button and

FUNC. button. Change the

batteries

Batteries are fully depleted and the camera can no longer operate. Replace the batteries immediately.

(21)

19

3 Select

(Format)

using or

and

press the SET

button.

4 Select [OK] using

or and press

the SET button.

z To cancel formatting instead, select [Cancel] and press the SET button.

z The capacity of the CF card displayed after formatting will be less than the rated capacity of the CF card. This is not a malfunction of the CF card or camera.

5 Press the MENU button.

z If the camera is not operating correctly, the CF card may be corrupted. Formatting the card may solve the problem.

z If you are using a CF card from another manufacturer and the card is not functioning correctly, you may be able to correct the problem by formatting the card.

z CF cards formatted with another camera, a computer or peripheral device may not operate correctly. Format these cards with this camera. If formatting in the camera doesn't work properly, turn the camera off and re-insert the CF card. Then turn the camera back on and format again.

About CF Cards

z CF cards are high-precision electronic devices. Do not bend them, apply force to them, or subject them to shocks or vibration.

z Do not attempt to disassemble or alter a CF card. z Moving a CF card rapidly between temperature

extremes will cause condensation to form in the card and lead to a malfunction. To avoid condensation, place the CF card in a sealed plastic bag before moving it into a different temperature zone and allow it to adjust slowly to the new temperature. If condensation forms on

(22)

Setting the Date/Time

The Date/Time menu will be displayed when

camera power is turned on for the first time or

at low date battery power. Perform

operations from Step 4 (Replace the date

battery when power from the current one is

exhausted (p. 105)).

1 Turn the power on (p. 23).

2 Press the MENU

button and select

the [

(Set up)]

menu using or

.

3 Select

(Date/

Time) using or

and then press

the SET button.

the CF card, store it at room temperature until the water droplets have evaporated naturally. z When storing the CF card, use the CF card case. z Do not use or store CF cards in the following

types of location.

• Locations subject to dust or sand

• Locations subject to high humidity and high temperatures

(23)

21

4 Set the date and

time.

z Use or to change the value of the highlighted field.

z Press or to set the date and time. z The date can be set up to the year 2030.

5 Press the SET button.

6 Press the MENU button.

z Setting the date and time settings does not cause the date/time stamp to appear on images. For printing images with the date on them, refer to page 80, the Direct Print User Guide or Software Starter Guide. z For important information, see

Replacing the Date Battery (p. 105).

Setting the Language

Sets the display language for LCD monitor

menus and messages.

1 Turn on the camera (p. 23).

2 Press the MENU

button and select

the [

(Set up)]

menu using or

.

3 Select

(Language)

using or

and

press the SET

button.

(24)

4 Select a language

using , ,

or

and press the SET

button.

z The setting menu will reappear without

changing the language setting if you press the MENU button instead of the SET button.

5 Press the MENU button.

Shortcut Operation

The Language menu can also be displayed in Playback mode by holding down the

SET button and pressing the MENU

button. (This function cannot be used while a movie clip is played back, or when a separately sold printer is connected to the camera.)

(25)

23

Basic Functions

Turning the Power On/Off

Shooting Mode

1 Open the lens cover.

z If you further slide it towards "open", the camera will power up. The indicator next to the viewfinder starts blinking green. z Close the lens cover again to turn the power

off.

Playback Mode

1 Press the

button until the

image is displayed on the LCD

monitor.

Open Close

z The indicator next to the viewfinder blinks green and the camera powers into Playback mode.

z Press the button again to turn the power off.

- You can print recorded images if you connect the camera to a separately sold printer (see Direct Print User Guide).

z You will hear a start-up sound and see the start-up image when the power is turned on. (To change the start-up sound and image, see Customizing the Camera (My Camera Settings) p.61, p.93) z The start-up image does not appear when

the LCD monitor is off.

Turning on the camera without the start-up sound and image

Press and hold the SET button, then turn on the power.

(26)

Basic Functions

Power Saving Function

This camera is equipped with a power saving function. Depending on the power saving setting, the camera may power down or the LCD monitor may go off automatically.

zAuto Power Down

[On]

Shooting mode:

Powers down approximately 3 minutes after the last time a camera control is accessed.

Playback mode:

Powers down approximately 5 minutes after the last time a control is accessed on the camera.

Printer Connection mode:

Powers down approximately 5 minutes after the last time a control is accessed on the camera or something is printed on the printer.

When the Auto Power Down Function Activates

Press the button again.

[Off]

The power saving function does not activate.

zDisplay Off

The LCD monitor automatically shuts off approximately 1 minute* after the last time a camera control is accessed.

* This time can be changed (p. 60).

When the Display Off Function Activates

The LCD monitor display turns back on if the shutter button is pressed halfway or when the lens cover is slid open.

z The power saving function is disabled during Auto Play or during a computer connection (p. 74, 84).

z You can turn off the power saving function in the Set up menu (p. 60).

(27)

25

Basic Functions

Switching between Shooting/

Playback

You can quickly switch between the Shooting

and Playback modes. This is convenient

when you wish to shoot again after checking

or erasing an image immediately after it is

shot.

When shooting mode

1 Press the

button.

z The camera switches to Playback mode. z Press the button again or press the

shutter button halfway to return to the Shooting mode.

When playback mode

1 Open the lens cover.

(28)

Basic Functions

Using the LCD Monitor

Use the LCD monitor to shoot and review images, for menu operations and playing back

images.

Pressing the DISP. button cycles the LCD monitor to the next mode.

Shooting Mode

The AF frame changes according to its On/Off setting. (LCD monitor On)

AiAF set to [On] (p. 64) AiAF set to [Off] (p. 64)

z Green: Focusing complete (focused AF frame) z Green: Focusing complete z Does not appear: Focusing difficulty z Yellow: Focusing difficulty

Standard

(No Information) (Information View)Detailed

DISP. Button

DISP. Button DISP. Button

No Display

Shots Remaining or Remaining Movie Time/ Elapsed time (Shooting mode) (sec.)

Spot AE Point Frame AF Frame

(29)

27

Basic Functions

zWhen a Shooting mode setting is changed, the settings appear on the LCD monitor for about 6 seconds even if the LCD monitor is set to Standard or No display. (The Shooting mode settings may not appear depending on the camera setting.) You can set the flash, Continuous mode, self-timer, Macro/Infinity modes and light metering settings while this information appears on the LCD monitor. z and the icons in the above appear

even when the information view is turned off. zIn addition to the above icons, the AF frame, spot

light metering frame, shots remaining or remaining movie time appear as shown on the left.

Shooting Mode p .35 Exposure Compensation p. 65 White Balance p. 66 ISO Speed p. 69 Photo Effect p. 70 Compression p. 36 Resolution p. 36 Flash p. 38 Macro/Infinity p. 40 Shooting Method p. 41

Light Metering Mode p. 65 Movie Recording Mode p. 45 Digital Zoom Setting p. 31 Camera Shake Warning p. 29

Low Battery p. 18

ISO

50 ISO100 ISO200 ISO400

(30)

Basic Functions

Playback Mode

* Detailed Display is not available in index playback (9 images).

Standard

File Number

Shooting Date/Time

Image Number and Total (Display Image/Total) No Display Detailed* Histogram Movie Length DISP. Button DISP. Button DISP. Button Compression Resolution

WAVE format sound memo Movie

(31)

29

Basic Functions

The image in the LCD monitor may darken when the monitor is used under sunlight or other strong lighting. This is not a defect.

z The on/off setting of the LCD monitor display mode is memorized when the camera is turned off. When the camera is turned on again it assumes the last mode. However, when the LCD monitor is turned on and the "Change the batteries" message appears, the LCD monitor may not automatically turn on the next time the camera is started. z Setting the shooting mode to , or

turns the LCD monitor on regardless of whether it is set to on or off.

z A slow shutter speed has likely been selected because of insufficient lighting if the upper indicator beside the viewfinder blinks orange after the metering preparations are complete and the camera shake icon displays in the LCD monitor. Set the flash to or , or affix the camera to a tripod to shoot. The following information may be displayed,

depending on the image.

Shooting Mode p. 35 Exposure Compensation p. 65 White Balance p. 66 ISO Speed p. 69 Photo Effect p. 70 Resolution (Movie) p. 36 Flash p. 38

Light Metering Mode p. 65

Macro/Infinity p. 40

In addition to the above, the histogram and recorded movie time are displayed.

An audio file other than a wave file, or a file with unrecognized format is attached. A JPEG file not supported by "Design Rule for Camera File System" standards. RAW file format

(32)

Basic Functions

z After you take a photo by fully pressing the shutter button, the image displays on the LCD monitor for approximately 3 seconds (or the review duration you set from 3 to 10 seconds). If you press the

SET button while the image is displayed,

it will continue to display (p. 34). z While a recorded image is displayed on

the LCD monitor, you can check the exposure with the graph (See About the Histogram). It shows the distribution of the brightness data. If the exposure requires adjustment, set the exposure compensation and re-shoot (Press the

DISP. button if the histogram and other

information is not shown.). z Please note that image information

recorded by this camera may not display correctly on other cameras and image information recorded by other cameras may not display correctly on this camera.

About the Histogram

The histogram is a graph that allows you to judge the brightness of the shot image. The greater the bias toward the left in the graph, the darker the image. The greater the bias toward to the right, the brighter the image. If the image is too dark, adjust the exposure compensation to a positive value. Similarly, adjust the exposure compensation to a negative value if the image is too bright (p. 65).

Sample Histograms

(33)

31

Shooting – The Basics

See Functions Available in Each Shooting Mode (p. 124) at the end of this manual to find out which settings can be changed in which shooting modes.

Auto Mode

In this mode, all you have to do is press the

shutter button and let the camera do

everything else.

1 Set the mode switch to

.

2 Aim the camera at the subject.

3 Press the DISP. button to turn the

LCD monitor on and use the

zoom button to achieve the

desired composition (relative

subject size in the viewfinder).

: The subject will be enlarged.

: The subject will be reduced. z Images can be digitally zoomed up to

approximately 5.1x.

z The digital zoom can be set to [Off] (p. 57). z The image will appear grainier as the

image is digitally zoomed. However, the actual recorded image is not as coarse as it appears in the LCD monitor. Digital zoom is unavailable in some modes (p. 125).

4 Press the shutter button halfway.

z The shutter has a two-stage operation (pressing halfway and pressing fully).

Pressing Halfway

The exposure and focus are automatically set.

Indicators show the state of the camera (p. 14).

5 Press the shutter button all the way.

Pressing fully

z The shutter sounds once, and the image is shot. The indicator next to the viewfinder blinks green while the image is being recorded to the CF card (p. 14).

(34)

Shooting – The Basics

z Functions Available in Each Shooting Mode (p. 124).

z With the Review function, you can change the length of time images show on the LCD monitor after shooting, or set it so they do not show at all (p. 34). z If the orange or yellow indicator blinks

while you press halfway, you can still press fully to take the shot.

z Images are first saved into the camera's internal memory before being recorded onto the CF card, allowing the next images to be taken immediately as long as sufficient space is available in the internal memory.

z The beep and shutter sound can be set on/off in the Set up menu (p. 59). z Even when the shutter sound is set to

[ , , (On)] (p. 61), no sound will be heard if [Mute] is set to [On]. z There is no shutter sound in movie

mode.

z Shots cannot be taken while the flash is charging.

Shooting with Viewfinder

You can save the power by turning the LCD

monitor off and using the viewfinder to shoot.

1 Compose the image so that the

subject appears in the center of

the viewfinder.

z Image Seen in Viewfinder vs.

Recorded Image

When shooting an image, a larger range than the one visible in the viewfinder usually gets recorded. You can confirm the actual range that will be recorded in the LCD monitor. In addition, due to the viewfinder’s specification, the range visible

(35)

33

in the viewfinder may actually differ from the actual recorded image. The closer the subject is to the lens, the more noticeable the difference will be. In some cases, portions of images shot up close that appear in the viewfinder will not appear in the recorded image. You are

recommended to use the LCD monitor during macro photography (p. 40). z About the AF Function

This camera employs AiAF (artificial intelligence autofocus) technology, which uses a broad metering field to calculate the focal distance with high precision. It delivers a crisp focus even when the photographic subject is slightly off-center. The camera can also automatically focus on the center when AiAF is set to [Off]. z AF-assist Beam

- The AF-assist beam will sometimes emit when the shutter button is pressed halfway to assist focusing in certain conditions, i.e. dark conditions.

- The AF-assist beam can be turned off (p. 57).

If animals are your subject, turn off the beam when shooting in the dark to avoid startling them. However, please keep in mind the following facts.

• If the AF-assist beam is turned off, it may become more difficult for the camera to focus.

• Even if the AF-assist beam is turned off, if the flash is on red-eye reduction auto or is in slow synchro mode, the red-eye reduction lamp may emit.

(36)

Reviewing an Image Right After

Shooting

After a photo is taken, the image displays on

the LCD monitor for 3 seconds. In addition,

the image will keep on displaying regardless

of the review duration setting if one of the

following operations is performed.

z Keeping the shutter button fully pressed z Pressing the button while the image is

displayed

Press the shutter button halfway again to stop displaying it.

You can perform the following while images are displayed.

• Display the setting details of the image (p. 28).

• Erasing Images Individually (p. 53) • Magnifying Images (p. 47) (When

pressing the SET button and displaying images)

Changing the Image Display

Duration

The length of time images are displayed after a photo has been taken can be changed from between 3 seconds to 10 seconds or turned off.

1 Press the MENU button.

z The [ (Rec.)] menu appears.

2 Select

(Review) using or

.

3 Select a Review

setting using or

and press the

MENU button.

z With the [Off] option, the image will not display.

z With the [3 sec.] to [10 sec.] options, the image will appear for the time selected even if you release the shutter button.

(37)

35

z You can continue to display the image as long as the shutter button is fully held pressed regardless of the Review setting. z Another picture can be taken even while the

last is displayed.

Selecting a Shooting Mode

The following modes are available with this

camera.

The settings selected for each mode are kept even if the shooting mode is changed. When the power is turned off, the settings are also retained for certain shooting modes, but not for others (p. 124).

Auto The camera automatically makes _{most of the settings for you.}

Manual

You can manually adjust the exposure, white balance, and other settings before shooting.

Stitch Assist

For shooting panorama composition images

Movie For shooting movies

Still image Movie

(38)

Selecting , ,

or

1 Set the shooting mode switch to

and press the SET button.

2 Select the shooting mode using

or , and press the SET button.

Selecting

1 Set the shooting mode switch to

.

z This will switch to movie mode.

Changing the Resolution and

Compression

You can change the resolution and

compression (excluding movie) depending on

the purpose.

* Paper sizes vary according to region.

Resolution Purpose L (Large) 2048 x 1536 pixels Large Small zPrint up to A4 size* 210 x 297 mm (8.3 x 11.7 in.) prints

zPrint up to Letter size*

216 x 279 mm (8.5 x 11 in.) prints M1 (Medium1) 1600 x 1200 pixels

zPrint postcard size

148 x 100 mm (6 x 4 in.) prints zPrint L-size 119 x 89 mm (4.7 x 3.5 in.) prints M2 (Medium2) 1024 x 768 pixels

zPrint card size 86 x 54

mm (3.4 x 2.1 in.) prints S (Small) 640 x 480 pixels zSend images as e-mail attachments

zShoot more images

(39)

37

Movies can be shot with the following resolutions.

Compression Purpose

Superfine High _Quality

Normal

Shoot higher quality images

Fine Shoot normal quality

images

Normal Shoot more images

Resolution

640 x 480 pixels 320 x 240 pixels 160 x 120 pixels

1 Press the FUNC. button.

2 Select *

or *

using

or .

*

The current setting is displayed.

3 Select the

compression or

resolution you

wish to set using

or .

4 Press the FUNC. button.

z Image File Sizes (Estimated) (p. 115) z Types of CF cards and resolution (p. 114)

Compression

Compression Number of recordable images

(40)

Using the Flash

Use the flash according to the guidelines

below.

Auto with Red-eye Reduction

The flash fires automatically as required by the lighting level, and the red-eye reduction lamp fires each time the main flash fires.

Auto The flash fires automatically as

required by the lighting level.

Flash On The flash will fire.

Flash Off The flash will not fire.

Slow Synchro

The flash timing is adjusted to slow shutter speeds. This reduces the chance that the background will be dark when shots are taken at night or in rooms with artificial lighting. The red-eye reduction lamp fires with each shot.

Use of a tripod is recommended.

Shooting Mode

1 Press ( on the omni selector)

as necessary to select the

desired flash mode.

: Available : Available only for the first image

2 Shoot the image.

z The flash will fire when the indicator next to the viewfinder lights orange (It won't fire if set to ).

z Shooting procedures are the same as for the Auto Mode (p. 31).

z Shots cannot be taken while the flash is charging.

— — —

(41)

39

z If the flash is used in macro mode, the light may not be controlled correctly. In this case, set a higher ISO sensitivity or use other light sources instead of using the flash.

z When shooting with a high ISO sensitivity and using the flash, there is more of a chance of overexposure the closer you are to the subject.

z Please note that a slow shutter speed will be selected in dark places when the flash is set to off or slow synchro. Be careful to avoid camera shake under these conditions.

Shooting in Mode

Be careful to hold the camera still to avoid camera shake.

Shooting in , or Mode

Fix the camera to a tripod since the shutter speed will be slower than in the

mode. If an image is dark in mode, reshooting in mode will make it brighter.

z The flash may take approximately 10 seconds to charge. The LCD monitor, if it is on, will go off after the indicator next to the viewfinder blinks orange while recharging. The LCD monitor will come back on after the indicator lights a steady orange when recharging is completed. Recharging time may vary according to shooting conditions and battery charge levels.

z The flash fires twice. A pre-flash will fire and will be followed by the main flash. The pre-flash is used by the camera to obtain the subject’s exposure data so that the main flash can be set to the optimal intensity for the shot.

Red-eye Reduction

z Light reflecting back from eyes can make them appear red when the flash is used in dark areas. Under these conditions, use the Auto with red-eye reduction mode*. For this mode to be effective, the subject must be looking right at the red-eye reduction lamp. Try asking them to look directly at the lamp. Even better results can be obtained by

(42)

increasing the lighting in indoor settings or coming closer to the subject. *The shutter will not activate for

approximately 1 second after the red-eye reduction lamp fires, even when the shutter button is pressed all the way down in order to improve the effect. If you want to have more immediate shutter response, set the flash setting to either , or .

Macro/

Infinity Modes

Macro

Use this mode when the distance from the lens tip to the subject is 5 to 20 cm (2 to 7.9 in.).

Infinity

Use this mode to shoot

landscapes. Also use this mode for compositions combining both near and distant objects.

Shooting Mode

1 Press

/

( on the omni

selector) to display

or

.

: Available : Available only for the first image

z Pressing / ( on the omni selector) cancels the macro mode.

2 Shoot the image.

If the flash is used in macro mode, the light may not be controlled correctly. In this case, set a higher ISO sensitivity or use other lightings instead of using the flash.

(43)

41

z Use the LCD monitor for shooting in macro mode. With subjects framed in the viewfinder when in macro mode, part of the image may not appear in the final shot (p. 32).

z The recordable area at the closest focal distance is approximately 56 x 42 mm (2.2 x 1.7 in.).

Self-timer

1 Press

/

( on the omni

selector) as necessary so that

or

appears on the LCD monitor.

z The image is shot 10 seconds ( ) or 2 seconds ( ) after the shutter button is fully pressed.

2 Shoot the image.

z See page 57 for information on how to select or .

z When is selected and the shutter button is pressed fully, the self-timer lamp starts

Shooting Mode

blinking and the self-timer begins to beep. The blinking gets faster 2 seconds before the shutter releases.

z When is selected and the shutter button is pressed fully, the self-timer lamp blinks fast from the beginning. The shutter releases in 2 seconds.

You can change the self-timer sound by changing the setting in [Selftimer Sound] in the [ (My Camera)] menu (p. 61).

Continuous Mode

Use this mode to shoot successive frames

while the shutter button is pressed.

1 Press

/

( on the omni

selector) as necessary so that

appears on the LCD monitor.

Shooting Mode

(44)

2 Press the shutter button halfway

to lock the focus.

3 Press the shutter button all the

way to shoot.

z Shooting will stop when the shutter button is released.

z The shooting speed is approximately 2.2 frames per second (Large/Fine, LCD monitor off).

(These figures reflect Canon’s testing standard. The actual figures will vary according to the shooting conditions and settings.)

z If internal memory becomes full, intervals between shots may lengthen slightly. z If you are using the flash, shots are

taken more slowly to allow time for the flash to recharge.

Shooting Panoramic Images

(Stitch Assist)

Stitch Assist can be used to shoot

overlapping images that can later be merged

(stitched) to create one panoramic image on

a computer.

There are two stitch assist modes based on the shooting direction as shown in the following.

Left Right Shoots horizontally from left

to right.

Right Left Shoots horizontally from _{right to left.}

(45)

43

To merge the images on a computer, use PhotoStitch, one of the supplied programs.

Framing a Subject

The PhotoStitch program detects the overlapping portions of adjoining images and merges them. When shooting, try to include a distinctive item (landmark) in the overlapping portions.

z Compose each frame so that it overlaps 30 to 50 % of the adjoining image. Try to keep the vertical misalignment to within 10 % of the image height.

z Do not include moving items in the overlap.

z Do not try to stitch images that include both distant and close items. Objects may appear warped or doubled up.

z Make the brightness in each image consistent. The final image will appear unnatural if the difference in brightness is too great.

z Pan (swivel) the camera to take successive shots.

z To shoot close-ups, slide the camera over the subject, keeping it parallel to the subject as you move.

Shooting

1 Set the Shooting mode to

or

.

z See Selecting a Shooting Mode (p. 35).

2 Shoot the first image.

z The exposure and white balance settings are set and locked with the first image.

(46)

3 Compose and

shoot the second

image so that it

overlaps the first.

z Minor discrepancies in the overlap can be corrected with the software.

z An image can be retaken. Press or to return to that frame.

4 Use the same procedures to

shoot the remaining frames.

z A maximum of 26 images can be recorded either horizontally or vertically.

5 Press the SET button after the

last shot.

Sequence

z A custom white balance setting (p. 68) cannot be set in / mode. To use a custom white balance setting, first set it in another shooting mode.

z The settings in place for the first image are locked in and cannot be changed for subsequent shots.

See page 124 for settings that can be changed in this mode.

(47)

45

Movie Mode

Use this mode to shoot movies. The

resolution can be set to [

(640 x 480)], [

(320 x 240)], or [

(160 x 120)] (p. 36).

1 Set the shooting mode switch to

.

z The LCD monitor turns on and displays the maximum recording time (in seconds).

2 Press the shutter button all the

way.

z Shooting and sound recording starts simultaneously.

z During the shooting a red circle appears in the upper right of the LCD monitor.

3 Press the shutter button all the

way to stop recording the movie.

z The maximum length of a movie clip (15 frames/sec) is : approx. 30 seconds*, : approx. 3 minutes, : approx. 3 minutes.

Shooting Mode

* Using the following CF cards: • Supplied FC-32MH CF Card

• Separately sold Canon FC-256MH or FC-512MSH CF Card (not sold in some regions)

These times may vary with the subject and shooting conditions. Recording will automatically stop when the maximum is reached or when the CF card runs out of free capacity.

z You are recommended to use a CF card that has been formatted in your camera to shoot movies (p. 18). The card supplied with the camera may be used without further formatting.

z The recording time may not display properly during shooting or filming may stop unexpectedly with the following types of CF cards.

- Slow recording cards

- Cards formatted on a different camera or a computer

- Cards which have had images recorded and erased repeatedly Although recording time may not display properly during shooting, the movie will

(48)

be recorded correctly on the CF card. Recording time will display properly if you format the CF card in this camera (excluding slow recording CF cards). z Be careful not to touch the microphone

while shooting.

z The AE, AF, white balance and zoom settings are set and locked to the settings of the first frame.

z The indicator next to the viewfinder blinks green after a shot. You cannot shoot again until it stops blinking.

z See page 124 for settings that can be changed in this mode.

z Sound is recorded monaurally. z There is no shutter sound in movie

mode.

z QuickTime 3.0 or higher is required to playback movie files (AVI/Motion JPEG) on a computer. (QuickTime (for Windows) is bundled on the supplied Digital Camera Solution Disk. On the Macintosh platform, QuickTime 3.0 or later is generally bundled with the Mac OS 8.5 or later operating system.)

(49)

47

Magnifying Images

Images can be magnified up to approximately

10 times during single image playback.

1 Press the

button.

z Pressing the button while holding the SET button magnifies the image approx. 2.5 times, approx. 5 times and 10 times in order.

z Press , , or to change the display position vertically and horizontally. z To return to normal-size display, press the

button several times.

Movie frames and index playback images cannot be magnified.

You can magnify an image while it is displayed on the LCD monitor in Shooting mode immediately after the image is shot (p. 34).

Approximate position

Displaying Images Individually

(Single Image Playback)

You can view the recorded images on the

LCD monitor.

1 Press the

button.

z The last image shot is displayed (Single Image Playback).

2 Press or to switch the

displayed image.

z Use to move to the previous image and to move to the next. Holding or moves more rapidly between images, but the images will not appear as clearly.

You may not be able to play back images that have been shot with another camera or edited on a computer with other software applications.

z Press the DISP. button to show the data for the displayed image (p. 28). z Press the button to quickly delete the

displayed image (p. 53).

Playback – The Basics

(50)

Playback – The Basics

Viewing Images in Sets of Nine

(Index Playback)

Up to 9 images can be viewed at once in

index playback.

1 Press the

button.

2 Press the

button.

z 9 images appear at a time (Index Playback).

3 Press , ,

or

to

select

the

image.

Pressing in this row

displays the previous set of 9 images.

Pressing in this row

displays the next set of 9 images.

Movie Selected Image

4 Press the

button.

z Index playback cancels and the display reverts to single image playback.

Press the DISP. button to show the data for the displayed image (p. 28).

(51)

49

Jumping between Images

The display can be advanced or set back 9

images when in index playback.

1 Press the

button in index

playback (p. 48).

z The jump bar appears.

2 Change the image

selection.

z Jump 9 images back or forward using or . z Hold the SET button and

press or to jump to the first or last image.

3 Press the

button.

z The jump bar disappears and the camera returns to index playback.

z If you press the button once more, the camera returns to single image playback.

Jump Bar

Viewing/Editing Movies

Viewing Movies

You can play back the images shot in

mode.

1 Press the

button.

z Movies cannot be viewed in index playback mode.

2 Press or to select a movie

and press the SET button.

z A movie displays with the icon on it. z The movie playback panel appears.

3 Select

(Play)

using

or

and

press the SET

button.

z The movie images and sound will play. z You can adjust the

volume using or .

Movie Playback

(52)

z When a movie has finished playing, it will display the last frame. If the SET button is pressed in this state, the camera will revert to the movie playback panel. If the SET button is pressed again, the movie will start playing from the first frame.

Pausing and Resuming Play

z Press the SET button to pause the movie.

Press it again to resume.

Fast Forwarding/Rewinding

z Select one of the following operations using or and press the SET button.

(Exit): Return to single image playback

(First Frame): Display the first frame (Previous Frame): Return to the previous

frame (Rewinds if the SET button is held down) (Next Frame): Proceed to the next frame

(Fast forwards if the SET button is held down) (Last Frame): Display the last frame

You may experience frame dropping and audio breakup when playing back a movie on a computer with insufficient system resources.

z The volume at which movies play back can also be adjusted in the Set up menu (p. 59).

z If you set [Mute] to [On] in the Set up menu (p. 58), no sound is reproduced. However, you can resume the sound and adjust the volume during movie playback using or .

Editing Movies

You can delete unwanted portions from the first or second half of the movie clip.

1 Select the movie you wish to edit,

and press the SET button.

(53)

51

2 Select

(Edit) using or

and press the SET button.

z The movie editing panel and the movie editing bar will appear.

3 Select the editing

method using

or

.

z (Cut beginning):Deletes frames in the first half of the movie z (Cut end): Deletes frames in the

second half of the movie z (Exit): Reverts to the movie

playback panel

4 Select the editing

position using

or .

5 Select

(Play) using or

and press the SET button.

z The temporarily edited movie will start playing.

z The movie will stop if you press the SET button while it is playing.

6 Select

(Save)

using or

, and

press the SET

button.

z When is selected, the edited movie is not saved and the camera reverts to the movie playback panel. Movie Editing Panel Movie Editing Bar