17-4 PH stainless steel
Microstructure and mechanical properties of biomedical alloys produced by Rapid Manufacturing techniques
... In-situ neutron diffraction analysis has been carried out at the Spectrometer for Materials Research at Temperature and Stress (SMARTS) in the Lujan Neutron Scattering Center in Los Alamos, NM. In-situ analyses are ...
192
The Effect of Long Term Isothermal Aging on Dynamic Fracture Toughness of Type 17 4 PH SS at 350°C
... The 17-4 PH (precipitation hardening) stainless steel is a martensite stainless steel containing approximately 3 mass% Cu and is strengthened by the precipitation of ...
6
Influence of Frequency on the High Temperature Fatigue Crack Growth Behavior of 17 4 PH Stainless Steels
... For Condition H900, the degree of variation of FCGR with frequency at 673 K is markedly greater than that of H1150 in the situations where DSA was present. For 17-4 PH stainless steel, ...
10
Morphological and Structural Characterization of Two Types of As-Received and In vivo Orthodontic Stainless Steel Brackets
... the 17-4PH SS or 316 SS, galvanic coupling forces the less noble materials to ...and 17-4PH stainless steel had the highest yield strengths compared to 310, 303Se and 316L stainless ...
14
Hot Deformation Behavior of 17-7 PH Stainless Steel
... Fig. 4 shows θ-ζ curves of 17-7 PH alloy at different deformation conditions and its corresponding minimum in –dθ/dζ curve for a typical deformation condition which approves the occurrence of ...
11
Effect of Precipitation Hardening on Microstructural Characteristics of 15-5 Ph Steel
... 15-5 PH is a delta ferrite-free compositional modification of 17-4 PH precipitation hardening martensitic stainless steel containing less chromium and slightly higher ...to ...
5
Influence of Frequency on High Temperature Fatigue Behavior of 17 4 PH Stainless Steels
... In general, fatigue failure can be divided into two steps: crack initiation and crack propagation. 10) For steels, the fatigue life of smooth surfaces was usually predominated by the crack initiation stage which took up ...
9
Effect of Electrode Materials on Electric Discharge Machining of 316 L and 17 4 PH Stainless Steels
... tool steel as work material and copper as electrode show that the roughness of finished surface increases with an increase in the discharge voltage, pulse current, and pulse duration ...tool steel used in ...
6
A Design Modification Approach to Utilize the Benefits of Metal Additive Manufacturing Adoption
... Pre-alloyed stainless steel powder (EOS Stainless Steel GP1) with material composition equivalent to the com- mercial 17-4 PH steel alloy and particle size range ...
7
Effect of Microstructure on Mechanical Properties of Friction Welded Joints between Ti and AISI 321 Stainless Steel
... The conventional fusion welding techniques between Ti and stainless steel have resulted in the segregation of chemical species, stress concentration and formation of intermetallics. Especially, the ...
7
Antiadherent and antibacterial properties of stainless steel and NiTi orthodontic wires coated with silver against Lactobacillus acidophilus—an in vitro study
... Surface modification of both stainless steel and nickel titanium orthodontic wires with silver was carried out by thermal evaporation method. The instrument used for coating is HINDHIVAC vacuum coating unit ...
6
Research Progress of Nickel free Lightweight Stainless Steel
... Nickel-free stainless steel compared to the traditional nickel-containing stainless steel has a obviously cost advantage and good comprehensive ...free stainless steel, and ...
8
Investigation of Residual Stresses in Welding and its Effect on Mechanical Behavior of Stainless Steel 310
... of stainless steel 310 longitudinal and transverse weldment specimen were compared with virgin alloy of stainless steel 310 to quantify the effect of residual ...
5
Corrosion Behavior of Common Metals in Eutectic Ionic Liquids
... mild steel in ChCl-Ur and ChCl-EG ...mild steel due to the presence of chloride ions ...and steel in CDES and reported to have significantly reduced corrosion rates in such media ...
20
Metallurgical Perspective of AISI 301LN (EN 1.4318) Grade Austenitic Stainless Steel for Future Transport Applications
... of stainless steels, austen- itic stainless steel especially AISI 300 series grades has highest production and commercial uses ...used stainless steel to manufacture railway coach ...
21
Comparison of mechanical properties and surface characteristics of space closure arch wires following fluoride treatment with topical fluoride gels and fluoride mouthrinses : An Invitro study
... (stainless steel and nickel titanium) and four brands of metal brackets were ...and pH 4 and pH 6 artificial saliva ...and stainless steel wires were corroded in the ...
86
Corrosion Resistance and Passivation Behavior of B-containing S31254 Stainless Steel in a low pH medium
... From the peak analysis, it is clear that chromium oxides are abundant in the outermost layer of the passive film of the borated sample, whereas the quantity of iron oxides is less. In recent studies, it has been found ...
15
Potential of Martensitic Stainless Steel X5CrNiCuNb 16-4 as Pipe Steel in Corrosive CCS Environment
... on-shore CCS-sites in the Northern German Basin. Additionally fatigue tests were performed via push-pull tests with a series of 30 specimens was tested at stress amplitudes between 150 MPa and 500 MPa (sinusoidal dynamic ...
8
Equal Channel Angular Pressing as a New Processing to Control the Microstructure and Texture of Metallic Sheets
... Recrystallisation has been enhanced in the final anneal- ing by introducing one-pass ECAP prior to cold-rolling in the 16 mass% Cr steel sheet. It was found that recrys- tallisation temperature was reduced almost ...
6
Composition and Type of a Binder Effects on the Stainless Steel Foam Microstructure Prepared by Sponge Replication Method
... development. Stainless Steel 316L (SS316L) foam has been fabricated by foam replication method at different SS316L powder composition which is 60 wt%, 65 wt%, and 70 ...
6