Al-Si alloys
3D imaging and quantification of porosity and intermetallic particles in strontium modified Al Si alloys
... modified alloys, the mechanism is still ...modified Al-Si alloys is essential to improve the melt quality, mechanical properties and to reduce hot tearing and wastage of ...of ...
26
NUMERICAL SIMULATION OF AL-SI ALLOYS WITH AND WITHOUT A DIRECTIONAL SOLIDIFICATION
... different Al–Si alloys: the mechanical behavior of the die cast alloy is isotropic in all three directions, while for the directionally solidified alloy, the mechanical strength in the direction of ...
9
Prediction of Solidification Paths in Al Si Fe Ternary System and Experimental Verification: Part I Fe Containing Hypoeutectic Al Si Alloys
... hypoeutectic Al-Si alloys were studied based on thermodynamic analysis and pertinent ...the Al-Si-Fe ternary system, a thermodynamic database for Thermo-Calc was correctly updated and ...
10
Modification of Al Si alloys by Ce or Ce with Sr
... (Al-Si) alloys are widely used in the automotive and aerospace industries due to their high strength-to-weight ratio, good castability, and excellent mechanical and performance proper- ...such ...
9
Tribological Studies of Eutectic Al-Si Alloys Used for Automotive Engine Blocks Subjected to Sliding Wear Damage
... hypoeutectic alloys like AA319 or AA 356 are used, cylinder liners made of cast iron or, in some cases, metal matrix composite must be ...hypereutectic alloys can also be used to a manufacture monolithic ...
169
3D atom probe tomography study on segregation of yttrium in modified Al Si alloys
... (Al-Si) alloys are widely used in automotive and aerospace industries due to their high strength-to-weight ratio, good castability, and excellent mechanical and performance ...hypoeutectic Al- ...
7
Yet Another Marked Difference among Impurities as Modifier Elements for Refinement of Eutectic Si in Al Si Alloys
... of Al-Si ...eutectic Si and its modification, exact crystal structure needs to be clarified for both categories of ...of Al 2 Si 2 Sr are reported, 14) ...
9
Effect of Silicon Particles on the EDM Characteristics of Al Si Alloys
... Those Al–Si alloys specimens with 4–12 mass% Si content exhib- ited hypoeutectic properties, determined by α -Al and acicular eutectic silicon particles ...mass% Si specimens, ...
7
The Correlation between Electrochemical Corrosion Resistance and Mechanical Strength of As-Cast Al-Cu and Al-Si Alloys
... Al-Si alloys with silicon as a major alloying element constitute a class of material, which provides the most significant part of all shaped castings manufactured, especially in the aerospace and ...
15
Development of Novel Nano - Single Si Phase Cast Hypereutectic Al-Si Alloys
... in Al-Si alloys [24] by decreasing the surface tension of the liquid and increasing volumetric shrinkage ...et al. [28] stated that Sr enhanced the susceptibility of the alloys to ...
372
Mechanical properties and corrosion behaviour of Al-Si alloys for IC engine
... three Al–Si alloys in 0.5 M NaCl solution. The alloys have exhibited similar values of hardness, but the highest tensile strength and the lowest elongation have shown the specimens of alloy ...
14
Prediction of Solidification Paths in Al Si Fe Ternary System and Experimental Verification: Part II Fe Containing Eutectic Al Si Alloys
... eutectic Al-Si alloys solidified under slowly- and rapidly-cooled conditions are summarized in Table ...eutectic Al-Si alloy are shown in ...
8
Structure Formation of Hypereutectic Al-Si-Alloys Produced by Laser Surface Treatment
... Hypereutectic Al-Si alloys have found application in the manufacture of tools [7] and automotive engine components ...these alloys increases with increasing of the Si ...the Si ...
6
Design and Analysis of Fin using Al-Si Alloys with Mg for improving Heat Transfer Efficiency
... Abstract : The Engine cylinder is one of the major automobile components, which is subjected to high temperature variations and thermal stresses. In order to cool the cylinder, fins are provided on the cylinder to ...
5
ELEVATED TEMPERATURE LUBRICATED WEAR OF Al-Si ALLOYS
... of Al-Si alloys, lubricated sliding investigations of Al-Si alloys is rather scarce considering their application in the engine ...of Al-Si alloys in the ...
309
EFFECT OF SILICON CONTENT ON MACHINABILITY OF Al-Si ALLOYS
... In the experimental study, 6 experimental samples (with a diameter of 15 mm and a thick- ness of 10mm) were prepared from each series to be used in microstructure analyses of Al-Si alloys. Sample ...
7
Tribological Study on Plasma Electrolytic Oxidation Treatment in Al-Si Alloys for Engine Application
... three sliding seals (as shown in Figure 59) with the purpose of separating the combustion gases above the piston head from the crankcase environment. The first ring from the top is called the compression ring with the ...
215
Hydrogen Internal Friction Peak in Amorphous Zr Cu Al Si Alloys
... variety among various a-alloys, suggesting that the detailed anelastic process for the HIFP is a function of the chemical composition of a-alloys. For the later-transition-metal/early- transition-metal ...
8
Amalgamation of al si alloys and study of their mechanical properties
... Alloy which is defined by metallic bonding character is a mixture of two or more metals or non- metals exhibiting different phases used to enhance the properties such as tensile strength and shear strength better than ...
7
Effect of Silicon on Microstructure and Mechanical Properties of Al-Si Piston Alloys
... cast Al–(4–20) % Si alloys are shown in Figure ...cast Al–4% ...cast Al–8% Si alloy shows that primary-aluminium grains are embedding in the ...region. Al–12% Si ...
5