Austenitic steel
Microstructure Development of Oxide Scale during Steam Oxidation of the Fe 20Cr 30Ni 2Nb (at%) Austenitic Steel at 1073 K
... new austenitic steel for realizing 800°C (1073 K) class power ...Commercial austenitic heat resistant steels such as SUS347HFG cannot meet these requirements, because carbides in the steels become ...
9
Effect of Grain Refinement on Thermal Stability of Metastable Austenitic Steel
... an austenitic stainless steel by using the reversion of deformation induced marten- site which has been formed by heavy cold-working, and also reported that the stability of austenite is greatly improved ...
7
Corrosion Behaviour of TiC Reinforced Hadfield Manganese Austenitic Steel Matrix In Situ Composites
... manganese austenitic steel matrix composite reinforced with the varying amount of TiC and unreinforced Hadfield manganese austenitic steel matrix alloy has been evaluated in ...
7
Design and Finite Element Analysis of Vertical Pressure Vessels Subjected To Applied Forces
... Vertical pressure vessels consist of a cylindrical shell and dished bottoms. They are placed on three welded legs. The size and positioning of the filler necks is adjusted according to the customer requirements and ...
9
Residual Stress Measurements at the Interface of Spot Welded Dissimilar Metals Between Carbon Steel and Austenitic Stainless Steel
... carbon steel and austenitic steel have been studied. Carbon steel SS400 with thickness of ...thick austenitic stainless steel SUS304 were joined in a lap joint by resistance spot ...
6
SURFACE MICROHARDENING STUDIES ON STEELS AFTER HIGH FEED MILLING
... The paper deals with the impact of high-speed machining production methods on the integrity of component surfaces. One has to point out that cutting conditions during machining have a significant impact on the final ...
9
Strain Rate Effects of Nuclear Steels in Room and Higher Temperatures
... This research area has been given early attention and dealt with in the past [2-6]. Within the EU project REVISA some additional topics, primarily centered on the size effect issue, have been addressed. The Transient ...
8
Metallurgical Perspective of AISI 301LN (EN 1.4318) Grade Austenitic Stainless Steel for Future Transport Applications
... grade austenitic steel are depending on the width of the extended stacking fault, micro bands and micro twins ...grade steel was composed of lath and dislocation cell martensiteas elucidate by spot ...
21
Fatigue Properties of Stainless Steel Wire Ropes for Electrodes in Functional Electrical Stimulation Systems
... stainless steel wire ropes with 19 strands developed for a functional electrical stimulation (FES) electrode in simulated body fluids were ...stainless steel wire ...
6
Dissimilar metal welding of J4-16cr. austenitic stainless steel with Grade 201LN austenitic stainless steel experimental analysis through optimization taguchi method
... this steel in ...of steel faced such like situation in the eighties due high Ni prices and import restrictions in ...stainless steel to ...stainless steel consumption. Actually on that time ...
7
Physical and tribological properties of Nitrided AISI 316 stainless steel balls
... nitrided steel balls was significantly better than that of the hardened 100Cr steel balls under identical testing ...M42 steel than the hardened 100Cr steel ...
6
Effect of Precipitation Hardening on Hardness and Microstructure of Austenitic Manganese Steel
... of Austenitic Manganese Steel has been studied. Samples of the steel were machined, autenitized at 1000 0 C and held for one hour, water quenched and then aged at different temperatures and holding ...
8
Identical Area Observations of Deformation Induced Martensitic Transformation in SUS304 Austenitic Stainless Steel
... A metastable austenitic stainless steel SUS304 was used in the present study. The chemical composition of the steel is shown in Table 1. A fully-recrystallized homogenous micro- structure of ...
6
Adherence of Carbon Steel Rust on the Corrosion of an Austenitic Stainless Steel Bolt in Marine Atmosphere
... The studied material was AISI 321 stainless steel with the chemical composition of 0.079C, 17.75Cr, 9.31Ni, 1.19Mn, 0.53Si, 0.56Ti, 0.030P, 0.0064S in wt%. The material was heated at 1050C for 20min and then ...
10
Physical and tribological properties of Nitrided AISI 316 stainless steel balls
... of austenitic stainless steels is their low hardness [10], typically 150 – 250 HV, which limits the wear resistance of components such as ball ...stainless steel can be enhanced significantly to 1000 HV by ...
11
Multiscale characterisation of the mechanical properties of austenitic stainless steel joints
... A multiscale investigation was pursued in order to obtain the strain distribution and evolution during tensile testing both at the macro- and micro-scale for a diffusion bonded 316L stainless steel. The samples ...
26
Corrosion behavior of austenitic stainless steel in high sulphate content
... There are also indications that higher sulfate/chloride ionic ratio is needed to inhibit the pitting corrosion of stainless steels at higher chloride concentrations [12].Stainless steel [r] ...
5
Study of Fatigue Crack Propagation in the Austenitic Stainless Steel 304L
... B. Effect of stress ratio on the fatigue crack growth rate In order to investigate the cyclic deformation behaviour of 304L stainless steel when it is subjected to mean stresses, numerical simulations were ...
7
Effect of Residual Stress on the Corrosion Behavior of Austenitic Stainless Steel
... stainless steel and the aluminum alloy, the role of compressive stress might be same as far as an auxiliary role for the construction and maintenance of the passive film ...stainless steel could be reduced ...
11
Study and Analysis of Austenitic Stainless steel of grade AISI 202
... of Austenitic Stainless steel of grade AISI 202 using an uncoated carbide insert tool was done at specific input values of speed, feed and depth of ...
23