controlled cooling
Controlled Cooling of Hot Rolled Steel Channels by Water Spraying on the Final Cooling Bed
... for controlled cooling of hot rolled steel channels by water spraying on the final cooling bed after continuous cast steel billets passing through reheating furnace and sequential rolls to form ...
7
Controlled Cooling of Onion Umbels by Periodic Sprinkling
... The ovary temperature response of onion florets on two different dates as a function of varying sprinkling times with wind speed and direction as noted (m/s, WNW, etc.).... Sprin- kling [r] ...
10
Optimal control of multiphase steel production
... We consider an optimal control problem that describes the hot rolling process of multi- phase steel, in particular dual phase (DP) steel. Dual phase steels have shown high poten- tial for automotive applications due to ...
32
Performance of electronically controlled automotive engine cooling system using PID and LQR control techniques
... the cooling system of theinternal combustion engine is an essential topic to enhance the vehicle performance during the different operating ...automotive cooling system has proven satisfactory for many ...
10
Intelligent controller for a cooling system for a three phase power transformer
... thermoelectric cooling module (TECM) was used as the cooling mechanism and testing it as a cooling device combined with the cooling liquid and pump for a prototype design of the actual ...The ...
10
Synthesis of super bright indium phosphide colloidal quantum dots through thermal diffusion
... a controlled cooling step for equili- bration of zinc sul fi de across the core, resulting in a photoluminescent quantum yield as high as 85% in organic solvent and 57% in aqueous ...
7
Membrane Cooling Technique for Cooling of Air
... O. Zeitoun, et.al [4] commented that the efficiency of the cooling system can be improved if the numbers of tubes were increased or the diameters were reduced. As commented in the literature, the optimization of ...
5
Development Of Smart Temperature Monitoring System Using Ubidots
... and cooling is consistently cooling the room dependent upon the settled temperature setting and is not normally adjusted for the comfort of the ...and cooling structure has transformed into a field ...
24
Integrated approach in building design for passive cooling in hot and dry climates of India
... evaporative cooling strategy ...evaporative cooling system as a promising approach to achieve thermal comfort in buildings ...on cooling process ...efficient cooling and ventilation in hot and ...
6
Neonatal ECMO Study of Temperature (NEST) - a randomised controlled trial
... All infants recruited to the study will be cared for in one of the four UK ECMO centres. Infants who require ECMO will be transferred to these centres from across the country. Babies who are thought to be eligible will ...
11
A Multistage Regulation Method for the Pad and Fan Cooling System
... fan cooling system in confined poultry house in ...evaporative cooling system under traditional ON/OFF ...evaporative cooling system was ...gradual cooling process has been ...adopt ...
5
Application Of The Cooling Pad As Evaporative Cooling System In Poultry House
... evaporative cooling, research and observation of evaporative cooling, factor affecting evaporative cooling, material of cooling pad, advantages and disadvantages of evaporative cooling ...
24
Modelling of Transient Temperature Field and Phase Transformation Change: A way for Residual Stress Management in Large Scale Forgings
... Figure 9 illustrates the equiva- lent stress predicted at different locations within the section for the cooling rate 5 ºC/s. The dashed curves presents stress level after implementing the dis- crete ...
10
A Comparative Study of Coolants Based on the Cooling Time of Injection Molding
... then cooling and solidifying ...optimal cooling system and operation conditions of the cooling process are very crucial to the injection molding process ...to cooling. In injection molding, ...
5
A magnetic resonance (MR) compatible selective brain temperature manipulation system for preclinical study
... reported that a decrease of temperature of about 4 ° C (systemic cooling) resulted in a reduction of 40% of CBF. In our study, a comparable result was found, with a 40% reduction of CBF when the brain temperature ...
10
A study of the effect of the FertilMate™ scrotum cooling patch on male fertility SCOP trial (scrotal cooling patch) study protocol for a randomised controlled trial
... collar filled with ice cubes that was attached to partici- pants’ thighs using tapes on either side and was applied for 30 minutes for 14 consecutive days. A second was a gel that became solid on freezing. It was wrapped ...
5
Computer simulation of evaporative cooling storage system performance
... The developed program is simple and efficient, with a suitable interface for the input of the necessary data, and the program provides sufficient information to optimize the design of an evaporative cooling system ...
13
Energy Saving Cooling-Unit for Plastic Moulding Machine
... Fig. 1. Energy flow in a compressed air system Air-leakages represent a particular problem in compressed air transport along the pipelines. The magnitude of this energy loss varies with the size and number of holes in ...
8
Influence of delayed cooling on quality of bell pepper (Capsicum annuum L.) stored in a controlled chamber
... place a lot of importance on the retention of their quality attributes during handling and storage (Sigge et al., 2001). Peppers rapidly lose water after harvest, which contributes to a major quality problem and has a ...
10
Influence of Cooling Channel Position and Form on Polymer Solidification and Temperature in Injection Molding Die
... in cooling time and quality of the ...through cooling channels. To study the influence of cooling channel position and forms, a full two dimensional transient type of analysis carried out using ...
9