Directional Drilling
Directional Drilling in ‘L’ Profile
... Directional drilling is a wellbore along a predetermined trajectory to intersect a designated subsurface ...target. Directional drilling has a long and interesting ...typical ...
9
An Estimation of Required Rotational Torque to Operate Horizontal Directional Drilling Using Rock Engineering Systems
... different drilling operations in a certain range of rock types, cannot be generalized for various ground ...horizontal directional drilling needs new innovative methods such as the RES-based model, ...
15
Identification and ranking risks of horizontal directional drilling for oil & gas wells by using fuzzy analytic network process, a case study for Gachsaran oil field wells
... This study attempts to identify and rank the Horizontal Directional Drilling (HDD) in the field of Gachsaran using of the linguistic preferences. The presented approach, inclusive thirteen risk in four ...
15
Stress Analysis of Buried Pipeline Installed by Horizontal Directional Drilling Using ANSYS Finite Element Software
... horizontal directional drilling (HDD) pipeline project, designers face the challenge of determining the regions of maximum and minimum stresses on pipelines, ensuring the stability of the bore-hole from ...
14
Optimization of Dogleg Severity in Directional Drilling Oil Wells Using Particle Swarm Algorithm (Short Communication)
... important directional drilling indices in a well of " Build & Hold " pattern will be considered (Figure 1), the difference is that the mechanical parameters of drill string that are affected by ...
13
SECTION HORIZONTAL DIRECTIONAL DRILLING (HDD)
... B. Directional Drilling System: The directional drilling system shall consist of over- the-road-transportable field power unit, mud-mixing and recycling unit, a trailer or carriage-mounted ...
17
Bottom Hole Assembly and Mud Motor for Directional Drilling
... include bursting of pipe, pipe stuck up etc.There is single method that can be adopted for drilling a directional well. The requirements for one type trajectory and angle of deviation may be different from ...
6
Stress analysis of operating gas pipeline installed by horizontal directional drilling and pullback force prediction during installation
... This dissertation is divided into six chapters: (1) Introduction; (2) HDD introduction; (3) Finite element method and model verification; (4) Stress analysis of the operating[r] ...
150
Geomagnetic Referencing Techniques As Vital Directional Reference In Hydrocarbon Drilling
... In directional drilling, magnetic declination i.e. the difference between true or geographic north and the magnetic north, is required to convert the survey measurements to the geographic reference frame. ...
6
Semiautomatic Drilling Machine Controller
... ABSTRACT: For precise job manufacturing, system should possess good dimensional accuracy and surface finish. In applications like drilling, punching, marking, boring, tapping work piece is positioned firstly and ...
8
A Brief History of Drills and Drilling
... The depression (arrow) was created by a slight elevation in the substrate and represents the region of greatest wear in the end of a solid rod-shaped drill (i.e., the shap[r] ...
9
Drilling Of Aero Composite Material
... to drilling carbon fiber-reinforced composite material, effects of drill bits on drilling of aero composite material, influence of process parameters on cutting force and torque, and backup plate ...
24
Development Of Vise For Drilling Machine
... According to Kibbe, R.R (2002) , drilling holes is one of the most basic of machining operations that is very frequently done by machinist. Metal cutting requires considerable pressure of feed on the cutting edge. ...
24
The Lake El'gygytgyn Scientific Drilling Project – Conquering Arctic Challenges through Continental Drilling
... El´gygytgyn Drilling Project, which is to investigate climatic developments during the Pliocene/Pleistocene transition and within the course of the Quaternary glacial/interglacial ...
12
Effect Of Drilling Parameters In Drilling Of Glass Fiber Reinforced Vinylester/Carbon Black Nanocomposites
... The drilling machine used for the experiment is sensitive drilling machine, With maximum and minimum feed rate is ...prepared. Drilling is carried out according to DOE, drill tool dynamometer used to ...
7
Fabrication of Universal Drilling Machine
... universal drilling machine is simply works on the principle of conversion of the electric energy from the battery in to the useful mechanical work in form of the rotational action of the chuck or spindle to ...
5
Structure of Thermal Drilling Joints
... conventional drilling processes, lubricant reduces friction and heat facilitates chip evacuation, unlike the friction-drilling technique, which is therefore defined as a clean ...
14
DRILLING, SAWING, GRINDING, CUTTING
... Once the tiles or fine stoneware have been bored through, a normal hammer or stone drill should be used for further drilling depending on the subsurface. When used on concrete, masonry or similar, the diamond ...
120
IBO - Self-drilling Anchor
... ■ No pre-drilling of a borehole by using a casing tube and extension rods with subsequent anchor installation necessary. ■ Minor space requirement for the accomplishment of anchori[r] ...
8
Changing the game for oilfield drilling
... The mobileFLEX portfolio is the latest advancement from GE to deliver lower-cost, lower-emission power to drill rigs, artifi cial lift- enhanced oil recovery, and oilfi eld equipment. An all-gas alternative to diesel ...
8