• No results found

Drilling performance

The Drill Geometry Influence on PCB Drilling Performance

The Drill Geometry Influence on PCB Drilling Performance

... better performance by measuring the flank ...after drilling 3000 ...the drilling in the semi-hermetic processing. The chips in drilling PCB is mostly the continuous floccule which is different ...

7

Comparative experimental investigation and gap flow simulation in electrical discharge drilling using new electrode geometry

Comparative experimental investigation and gap flow simulation in electrical discharge drilling using new electrode geometry

... Discharge Drilling (EDD) ...eral drilling operations were performed on stainless steel 304 using rotary tubular electrodes with circular and side-cut ...geometries. Drilling performance was ...

10

Analysis of Tool Wear Rate in Drilling Operation using Scanning Electron Microscope (SEM)

Analysis of Tool Wear Rate in Drilling Operation using Scanning Electron Microscope (SEM)

... the drilling performance of unalloyed carbon, case hardened, and tool ...the drilling work piece. Heat generated during drilling caused cutting tools to be subjected to high temperature and ...

12

Optimization Drilling Parameters Performance During Drilling in Gas Wells

Optimization Drilling Parameters Performance During Drilling in Gas Wells

... optimize drilling parameters such as WOB, ROP, RPM, flow rate and drill diameter of ...of drilling parameters. Drilling optimization is very important during drilling operation, to save time ...

8

Optimization Of Drilling Parameters On Surface Roughness In Dry Drilling Process Of AISI D2 Tool Steel

Optimization Of Drilling Parameters On Surface Roughness In Dry Drilling Process Of AISI D2 Tool Steel

... the drilling process is very important especially in making small ...small drilling hole is widely used in industries especially in producing precision products spanning from the manufacturing of fuel ...

24

High Performance Water-based Drilling Fluids—A High Efficiency Muds Achieving Superior Shale Stability While Drilling Deepwater Well with HPHT in South China Sea

High Performance Water-based Drilling Fluids—A High Efficiency Muds Achieving Superior Shale Stability While Drilling Deepwater Well with HPHT in South China Sea

... deepwater drilling operation, low temperature, high pressure, gas hydrate, narrow density window are the major challenges for drilling fluids to meet, and with the increasing depth drilled, high temperature ...

6

Optimization of Twist Drill Tool Hase Anita V. , Prof. M. S. Mali, Dr. S. B. Zope

Optimization of Twist Drill Tool Hase Anita V. , Prof. M. S. Mali, Dr. S. B. Zope

... purposes. Drilling process that reduces drill thrust force can decrease the risk of ...of drilling tools and machining parameters to extend the lifecycle of these laminates to enhance ...

5

Effect of Material Removal Rate (MRR) on AISI H11 Die Steel in Drilling using Face Centered Design

Effect of Material Removal Rate (MRR) on AISI H11 Die Steel in Drilling using Face Centered Design

... Drilling is one of the most common and fundamental machining processes. In machining, twist drills with diameters of 1–20 mm are used. Most of automotive components are manufactured using a conventional machining ...

11

Vol 46, No 2 (2016)

Vol 46, No 2 (2016)

... Geotechnical study comprises the work carried out by the geotechnical exploration within the area of site area 660 sq.m., located in Caracal, B.P. Hasdeu Street. To determine the geotechnical characteristics of the ...

6

Optimization of Parameters CO2 Laser for Drilling Different Types of Glass

Optimization of Parameters CO2 Laser for Drilling Different Types of Glass

... for drilling (2 - 8 ...for drilling the organic glass, we observe no micro-cracks, and again we see that the edges of the holes have a good surface quality with a high aspect ...

9

PERFORMANCE STUDY OF CRYO TREATED HSS DRILLS IN DRILLING CAST IRON

PERFORMANCE STUDY OF CRYO TREATED HSS DRILLS IN DRILLING CAST IRON

... Experimental approaches to study the effect of different parameters on the response variable usually involve a lot of time and material. Moreover, once a model is validated using some established experimental results; it ...

7

The Performance Analysis Of High Speed Steel Tool In High Speed Drilling

The Performance Analysis Of High Speed Steel Tool In High Speed Drilling

... Based on the table above, there is differentiation between the types of speed. For this project, we used high speed drilling which is 600 to 1800 m/min. Now, spindle rotational speeds in machine tools can range up ...

24

Experimental Investigation to Optimize Process Parameters in Drilling Operation for Composite Materials

Experimental Investigation to Optimize Process Parameters in Drilling Operation for Composite Materials

... in Drilling of Carbon Fibre Reinforced Plastic Composites using Response Surface Methodology”, International Journal of Modern Engineering Research (IJMER) ...damage-free drilling of carbon fiber reinforced ...

10

Drilling into the functional significance of stereopsis: The impact of stereoscopic information on surgical performance

Drilling into the functional significance of stereopsis: The impact of stereoscopic information on surgical performance

... The intuition that stereopsis might be important in den- tistry is reflected in the design of dental surgical simulators which provide realistic haptic feedback and 3D rendered images for the purpose of training. There ...

9

Development of Film Forming Agent HN 1 and Its  Application in Drilling Fluid

Development of Film Forming Agent HN 1 and Its Application in Drilling Fluid

... permeable drilling fluid was beneficial to improving stress sensitivity formation bearing pressure, and protecting reservoir, as well as its wide formation ...in drilling fluid from invading ...the ...

5

Design Of Automatic Fixture For Scantool Drilling Machine

Design Of Automatic Fixture For Scantool Drilling Machine

... SCANTOOL Drilling Machine, workpiece holding devices for drilling operation, types of clamping system and the sensors that will be used to detect the presence of workpiece and force sensor for determine ...

24

BELBIC Tuned PI Controller Based Chopper Driven PMDC Motor

BELBIC Tuned PI Controller Based Chopper Driven PMDC Motor

... In Osteosynthesis process, the screwing of bones is accomplished in three phases viz. insertion, tightening and stripping. The speed and torque requirements are set depends on the phase. It may be noted that the speed ...

13

The Estimated Formation Pressure During Drilling Operations, in Drilling Wells, and an Exploration of Steps towards Efficient Drilling

The Estimated Formation Pressure During Drilling Operations, in Drilling Wells, and an Exploration of Steps towards Efficient Drilling

... mud drilling , it is recognized as the heart of the drilling ...from drilling mud, the fluid formation is prevented from flowing from the wellbore to the ...by drilling fluid prevents it from ...

5

Methodology for Determining the Cutting Conditions in Drilling of Automated Manufacturing

Methodology for Determining the Cutting Conditions in Drilling of Automated Manufacturing

... of drilling. The choice of drilling technology is based on the design requirements for the shape and dimensions, namely the nature of semi-fi nished product, with regards to the requirements of quality, ...

8

Multiple performance 
		optimization of drilling parameters and tool geometries in drilling GFRP 
		composite stacks using Taguchi and grey relational analysis (GRA) method

Multiple performance optimization of drilling parameters and tool geometries in drilling GFRP composite stacks using Taguchi and grey relational analysis (GRA) method

... in drilling composite ...in drilling of carbon fiber-reinforced polymer reported that drill point angle influence the thrust force when it is combined with the effect of wear ...in drilling of ...

8

Show all 10000 documents...

Related subjects