• No results found

electro-static discharge

Analysis of Electro Static Discharge on GaAs
-Based Low Noise Amplifier

Analysis of Electro Static Discharge on GaAs -Based Low Noise Amplifier

... studies static effect of communication Low Noise Amplifier (LNA) that utilizes GaAs ...the Electro-Static Discharge (ESD) effect, which occurs within communication components, such as GaAs ...

15

CSC Hard Drive Bible 7th Edition 1994 pdf

CSC Hard Drive Bible 7th Edition 1994 pdf

... E ECC Error Correction Code ED Floppy Support EISA Cards Electro-Static Discharge ESD Embedded Servo Embedded Servo System EMS Cards Encoding and Decoding Codes ENDEC Enhanced IDE Erasab[r] ...

329

Design A Up Side Down Robot Gripper

Design A Up Side Down Robot Gripper

... Robot is usually using in industries technology especially in heavy industries. And it is also popular by replacing human to do some work which is dangerous to do by human, for example is chemical work, Electro ...

24

Parametric Optimization of Wire Cut Electro- Discharge Machining Process for Surface Finish and Kerf Width for H-31 Tools Steel

Parametric Optimization of Wire Cut Electro- Discharge Machining Process for Surface Finish and Kerf Width for H-31 Tools Steel

... The e xperimental setup and the experiment is designed and carried out at the Prec ision Die Cut wire cut wh ich is placed at Odhav, Ahmedabad .the primary goal of the dissertation work is to predict the surface ...

5

REMEDY OF WIRE LAG IN WIRE ELECTRICAL DISCHARGE MACHINING (WEDM) S. K. SINHA

REMEDY OF WIRE LAG IN WIRE ELECTRICAL DISCHARGE MACHINING (WEDM) S. K. SINHA

... (2003), “An analysis and optimization of the geometrical in accuracy due to wire lag Phenomenon in Wire- electro discharge machining,” International Journal of Machine Tool and Manufactu[r] ...

5

Optimization of Process Parameters in Die Sinking EDM- A REVIEW

Optimization of Process Parameters in Die Sinking EDM- A REVIEW

... Electrical discharge machining (EDM) is one of the earliest non-traditional machining ...of electro-conductive ...electrical discharge machining (EDM) is one of the most widely used techniques for ...

6

Optimization of Micro-EDM Process and its Performance Characteristic

Optimization of Micro-EDM Process and its Performance Characteristic

... Micro-EDM Electro discharge machining (EDM) is a known and it is most widely used nonconventional machining process for hard materials because of its ability to function on brittleness, hardness or ...

11

Oscillatory and burst discharge in the apteronotid electrosensory lateral line lobe

Oscillatory and burst discharge in the apteronotid electrosensory lateral line lobe

... burst discharge are shown in ...burst discharge in each of the segmental maps is plotted in ...spike discharge attained from the CMS to the LS ...

11

Performance evaluation of wire electrode discharge machining (WEDM) On Inconel 718

Performance evaluation of wire electrode discharge machining (WEDM) On Inconel 718

... electrical discharge machining (WEDM) has been improved significantly to meet the requirements in various manufacturing needs, especially in the precision mold and die ...

19

Electrical discharge machining of polycrystalline diamond using copper electrode – finishing condition

Electrical discharge machining of polycrystalline diamond using copper electrode – finishing condition

... Electrical Discharge Machining (EDM) is a noncontact thermal erosion process in which the metal is removed by a series of recurring electrical discharges between the electrode and the electrically conductive ...

7

Parametric Optimization of Electro Discharge Machining of Al/Al 2 O3 MMC

Parametric Optimization of Electro Discharge Machining of Al/Al 2 O3 MMC

... electrical discharge texturing of cutting tools to bring about a significant reduction in machining force through enhanced lubrication of the tool-chip ...time, discharge current and dielectric flushing ...

6

Drilling Microholes in Hot Tool Steel by Using Micro Electro Discharge Machining

Drilling Microholes in Hot Tool Steel by Using Micro Electro Discharge Machining

... when the depth exceeds 200 mm, due to difficulties of flushing debris away, the corner of the electrode begins to wear. As the depth increases, the corner wear increases drastically. This also leads the bottom of the hole ...

6

Optimization of Process Parameters on Material Removal Rate through Electro Discharge Machining

Optimization of Process Parameters on Material Removal Rate through Electro Discharge Machining

... electrochemical discharge machining (ECDM) is having high quality of material removal rate with zero residual ...electrochemical discharge machining ...

8

Process Parameters of the Surface Characteristics of Aluminium & HSS by Electro Discharge Sawing Machining

Process Parameters of the Surface Characteristics of Aluminium & HSS by Electro Discharge Sawing Machining

... Being highly susceptible to oxidation aluminium forms faster the insulating film essential for the arc gap formation and arc extinction before the onset of next arc discharge. On the other hand, for H.S.S. silicic ...

5

Surface Integrity in Micro Hole Drilling Using Micro Electro Discharge Machining

Surface Integrity in Micro Hole Drilling Using Micro Electro Discharge Machining

... Micro-Electro Discharge Machining Micro-EDM is one example of a high-precision machining process. It is a particularly important process since its application is uncon- strained by the hardness or material ...

5

Influence of Machining Parameters on Electro Discharge Machining of NiTi Shape Memory Alloys

Influence of Machining Parameters on Electro Discharge Machining of NiTi Shape Memory Alloys

... Through the design of experiments, the key variables that affect the qualitative characteristics of the process can be identified. By using this method, the controllable input factors can be systematically changed and ...

10

Study on Approach of Static Security Assessment  Accounting for Electro thermal Coupling

Study on Approach of Static Security Assessment Accounting for Electro thermal Coupling

... As an indispensable technology to guarantee the security operation of power grid, the on-line static security as- sessment (SSA) has been being focused by both aca- demic and engineering circles [1-3]. It takes ...

5

CRYOGENIC TREATMENT IN ELECTRO- DISCHARGE MACHINING – A REVIEW

CRYOGENIC TREATMENT IN ELECTRO- DISCHARGE MACHINING – A REVIEW

... during electro discharge machining of M2 grade high speed ...in discharge current. This could be due to an increase in discharge energy with increase in discharge current, which ...

13

Micro Electro Discharge Machining for Nonconductive Ceramic Materials

Micro Electro Discharge Machining for Nonconductive Ceramic Materials

... AE is an additional conductive layer on the workpiece that is applied to initiate sparks during machining or structuring of nonconductive ceramic materials [19]. There are two methods of applying AE. In the first method, ...

8

Wire Electro-Discharge Machining of Advanced Engineering Materials

Wire Electro-Discharge Machining of Advanced Engineering Materials

... The spectrometer used was an Ocean Optics USB2000 near-infrared spectrometer. Its wavelength range includes 0.717 to 0.980 µm. This spectrometer uses charge-coupled discharge (CCD) arrays to allow acquisition of ...

60

Show all 10000 documents...

Related subjects