• No results found

Flow rate through valves at varying pressures

Determination of flow rate characteristics for pneumatic valves

Determination of flow rate characteristics for pneumatic valves

... OF FLOW RATE CHARACTERISTICS FOR PNEUMATIC VALVES Zdeněk VARGA, Petri KESKI-HONKOLA A Abstract: The standard ISO 6358 is often used for describing flow rate of pneumatic ...mentioned ...

12

Determination of flow-rate characteristics and parameters of piezo pilot valves

Determination of flow-rate characteristics and parameters of piezo pilot valves

... directional valves are used in most industrial pneumatic ...two-stage valves controlled by a pilot valve. Pilot valves are often chosen ...the flow-rate characteristics and parameters ...

5

Liquid film flow-rate measurement at elevated pressures.

Liquid film flow-rate measurement at elevated pressures.

... stream flow rates. Flow rates were adjusted by throttling valves downstream of the ...required flow rates were obtained from a series of tables produced by use of ...

84

Flow Control valves

Flow Control valves

... non-compensated flow con- trol devices. Flow regulators — This device, Figure 2, which is slightly more sophis- ticated than a fixed orifice, consists of an orifice which senses flow rate, as ...

6

The time dependent flow through throttle valves: a computational and experimental investigation

The time dependent flow through throttle valves: a computational and experimental investigation

... velocity measurements, turbulence values, flow temperature, flow rate, throttle position,. and both absolute and differential pressures[r] ...

324

Hydraulic Flow Control Valves

Hydraulic Flow Control Valves

... Proportional Flow Dividers P R O P O R T I O N A L FLOW DIVIDERS split a single input flow into two output flows, each output being a fixed proportion of the ...input flow into two equal ...

38

Experimental Modelling and Identification of Compressible Flow through Proportional Directional Control Valves

Experimental Modelling and Identification of Compressible Flow through Proportional Directional Control Valves

... Control Valves; Identification, Experimental, Compressible Flow; Mechatronic Systems ...mass flow rate through a proportional valve’s orifices is a basic control issue in pneumatic ...

10

One-way flow control valves

One-way flow control valves

... one-way flow control valves regulate the piston speed of pneumatic drives during advance and return ...done through suitable restriction of the flow rate of compressed air in exhaust ...

38

Guidelines for operation of minimum flow control valves

Guidelines for operation of minimum flow control valves

... total flow rate is double the minimum flow rate including a safety factor, the minimum flow control valve (BR 1335-68) ...minimum flow control valve (BR 1335-68) after normal ...

10

A practical approach to the evaluation of subcritical multiphase flow through down-hole safety valves. (storm chokes)

A practical approach to the evaluation of subcritical multiphase flow through down-hole safety valves. (storm chokes)

... The cross-plot of Figure 7 makes a comparison between some of the existing sub-critical multiphase correlations with our model. The diagonal line is the actual solution, while the data points are the predicted multiphase ...

13

Wavefront shaping for flow-field measurements through varying phase boundaries

Wavefront shaping for flow-field measurements through varying phase boundaries

... Adaptive optics (AO) originally known from astronomy [1], has the great potential to clear up information-containing- light of any distorting effect. The wavefront manipulation is commonly performed using e.g. deformable ...

8

Reducing Rejection Rate by Applying Varying Parameters on Crankcase through Investment Casting Method

Reducing Rejection Rate by Applying Varying Parameters on Crankcase through Investment Casting Method

... Machine: Injection molding machine. Material : Wax. b) Expandable patterns and gating system: an expandable pattern may be made of wax being more commonly used small shallow vents cut in the parting surface of the die ...

5

Aerodynamic investigation on the effect of varying through-hub flow on a Formula One front wheel assembly.

Aerodynamic investigation on the effect of varying through-hub flow on a Formula One front wheel assembly.

... at varying through-hub flow rates which were measured using a pitot-static tube situated in the entry of the brake ...of through-hub flow on a rotating exposed wheel is not an ...

18

Check Valves, Flow Control and Priority Flow Control Valves

Check Valves, Flow Control and Priority Flow Control Valves

... check valves are offered in two configurations: nose-to-side free flow, port 1 to port 2, and side-to-nose free flow, port 2 to port ...free flow configuration is the preferred version for ...

8

Patient Flow Pressures

Patient Flow Pressures

... • In August 2013, the average length of stay (turnover rate) was 3.0 years, a reduction from 3.6 years reported in 2008*. • HNHB LHIN, on average, has less than 30 idle LTCH beds per month, an idle bed refers to a ...

18

Pipe Valves, Fittings and Nipples Pressures to 15,200 psi

Pipe Valves, Fittings and Nipples Pressures to 15,200 psi

... stem valves, for 2-way angle patterns, increase the Cv value by 50% ...pipe valves with metal to metal seats have a high level of safety and reliability under adverse operating conditions ...These ...

10

Chapter 5: Flow Valves

Chapter 5: Flow Valves

... 5 Catalogue HY11-3500/UK Catalogue HY11-3500/UK Manatrol needle valve with steel body as screw-in valve for block insertion, optionally with a 30° taper fine V-notch or micro-fine rectangular slot. The form of the ...

23

Air flow through two layered mesh at varying porosity and spacing

Air flow through two layered mesh at varying porosity and spacing

... protrude through two layers of mesh and hence burnt ends of the grass in case of fire would not start a spot fire on the other side of the second layers, provided the area between two layers at the base is clear ...

189

Valves with flow control by synthetic jets

Valves with flow control by synthetic jets

... the valves discussed ...fluid flow supplied into the supply terminal S is required for the majority of operation time to pass into the valve output terminal Y 1 - and only occasionally is to be switched ...

16

Reduced Flow of Control Valves, yes or no ?

Reduced Flow of Control Valves, yes or no ?

... control valves, the question is often raised how to reduce the valve flow without changing the valve ...control valves to have a long life and to operate faultlessly, no matter how demanding ...

9

Show all 10000 documents...

Related subjects