improved on-line control process
Plasma Process Control for Improved PEO Coatings on Magnesium Alloys
... red line in ...plasma process increase, the diffusion coefficient D increases and, therefore the flux of oxygen towards the substrate increases as ...the process, the number of very small discharges ...
227
Monitoring and controlling critical process parameters at the retort production line of Abbott Zwolle
... the process that we measure and the intention of the use of the ...the process is not yet in control. In Phase I we make control charts from historical data samples to see if there were any ...
81
A Combined System for Off-Line Optimization and Adaptive Adjustment of the Cutting Parameters During a Ball-End Milling Process
... the process of ball-end ...cutting process (ANfis-system) used for working out the CNC milling simulator has been ...hybrid process modelling, off-line optimization and feed- forward neural ...
18
Expert systems in on-line process control and fault diagnosis
... The reason for employing such an information pre-processor is that several qualitative model based diagnosis systems have been developed for the mixing process, and from which the traini[r] ...
227
On line quality control and experimental design analysis for plastic injection moulding : a thesis presented in partial fulfilment of the requirements for the degree of Master of Technology in Manufacturing and Industrial Technology at Massey University
... Computer based shop floor quality data acquisition and on-line quality control with more advanced statistical methods - such as statistical process control and design of experiments - ca[r] ...
126
Optimisation Of Conventional Process Control System By Applying Hybrid Technique Of Soft Computing
... logic control: First, fuzzy logic can easily be applied to most industrial applications in industry, the capacity of conventional controllers is significantly reduced when applied to systems with non- ...fuzzy ...
7
Indigenizing Sustainabilities, Sustaining Indigeneities: Decolonization, Sustainability, and Education
... the process and challenges of forming a broad collaborative research coalition within a Western institution, Jacob and Blackhorn discuss how such initiatives must proceed with “care, respect, reciprocity, and in ...
8
Integration of value stream map and strategic layout planning into DMAIC approach to improve carpeting process
... (preparation-installation) process nonconformities. In the studied case, the carpeting process was improved through: implementing the EWMA control chart in the carpet workshop as a ...
24
Rechallenge of oxaliplatin-containing regimens in the third- or later-line therapy for patients with heavily treated metastatic colorectal cancer
... Descriptive statistics were reported as proportion and median. Tumor responses were assessed by RECIST 1.1 criteria every 6–8 weeks. Radiologic evaluation consisted of chest and abdominopelvic CTs. Time to treatment ...
7
Improving Performance Of Microstrip Antenna Using Dual Feed Line Technique
... iteration process is done by controlling the dimensions of W1, L2 and L3 because these parameters have the most influence on the simulation process of the proposed ...iteration process of the ...
5
Guardian of the Line of Control
... Abstract: Border security is very risky work to maintain the peace in the country and to prevent the enemies from entering the country illegally by crossing the border. This paper elaborates the solution by which the ...
6
Production Control Analysis of Main Body using Statistical Process Control (SPC) Method
... production process has quality standard which set company, this research will analyze quality control Main Body production which is on production we still found defect so that do not reach target ...
6
Bevacizumab plus chemotherapy as third- or later-line therapy in patients with heavily treated metastatic colorectal cancer
... ECOG performance status of 2 in the whole cohort of bevacizumab-treated patients, which might have led to a more favorable OS estimate in these patients. Second, the small cohort in this study may also affect the ...
7
Redundancy and multiple objectives in linear robust control
... the control engineering theoretician is to address synthesis problems which have been identified as being of practical ...the control law or in the ...
272
Fault detection and diagnosis, FDD via improved univariate statistical process control charts, USPC
... SPC variable is categorized into lwo i.e qualiry varisbies and process variables. The qualily vadables acled as an indicaior variabLes to show thal lhe Process in the slate of statisti[r] ...
7
Process Line Balancing & Automation by Cellular Manufacturing Process
... on line balancing technique. Line balancing is an effective tool to improve shop-floor layout which in turn reduces product cycle ...productivity, improved machine utilization and better ...whole ...
14
The Dartmouth Time Sharing System 1980 pdf
... stack stack pointer pointer to next PDB TCFACE number for this line pointer to UMLC output vector for this line pointer to device control process pointer to current location in input pro[r] ...
244
A case study in off-line quality control: Characterization and optimization of batch dyeing process design
... batch dyeing process. Briefly stated, these objectives are: 1) Minimize color difference from target, 2) Maximize color uniformity within a piece of fabric, and 3) Minimize color variati[r] ...
47
Implementation of Statistical Process Control Techniques in Industry: A Review
... or process is a must for any ...the control chart that cannot help to remove the assignable causes of variation ...and control phase SPC tools are very useful and play the vital role for finding ...
5
Comparison of optimised composite control charts: improved statistical process control for the manufacturing industry
... for control charts have been proposed to manage the effect of estimating ...the control limits be widened according to the uncertainty in the parameter estimates such that the ICARL specification is ...the ...
171