Influence of deposition rate
Deposition of Pyrolytic Silicon Carbide on Discs in a Fluidized Bed EUR 4946
... The influence of the deposition conditions on density, microstructure, crystallite size and chemical composition of the material was determined.. Besides temperature the deposition rate [r] ...
36
Influence of CeCl3 and Deposition Parameters on Electroless NiFeP Deposition
... understood. With peculiar electronic structure and unique behavior, rare earth cerium will adsorb preferentially at the surface on the substrate. The adsorbed cerium tends to give away electrons and part cerium becomes ...
9
A robust upscaling of the effective particle deposition rate in porous media
... colloid deposition literature has been to study in detail simplified models representing a single collector, followed by a heuristic step providing the link between solute transport in the vicinity of one ...
18
Influence of pH Solution on Electroless Copper Plating Using Sodium Hypophosphite as Reducing Agent
... electroless deposition of copper-rich Cu–Ni–P alloys, using hypophosphite as reducing agent, has been carried ...The deposition rate increased obviously with the increase of ...
10
Studies on the Influence of Electroless Copper Deposition Process – A Review
... Addition of few ppm of Stabilizers increases the stability of the bath , which reduces the deposition rate but increase the brightness of the coatings[39 – 45]. Additives that stabilize the bath against the ...
7
Effect of substrate temperature on the properties of diamond-like carbon deposited by PECVD in methane atmosphere
... In this paper we investigate the influence of the substrate temperature on the deposition rate and Raman scattering of DLC films deposited using PECVD technique in pure (99.5%) methane a[r] ...
5
Atmospheric Corrosion of Reinforced Concrete Steel in Tropical Coastal Regions
... the influence of the environment in coastal and marine sites is the necessary time to reach the critical chloride content or chloride threshold in the reinforcing steel rebars ...chloride deposition ...
18
A robust upscaling of the effective particle deposition rate in porous media
... colloid deposition in arbitrary porous media geometries, we assume a time- and length-scale separation hypothesis between the superfi- cial phenomena and the pore-scale transport, that allows to lump all the local ...
28
Influence of argon plasma on the deposition of Al2O3 film onto the PET surfaces by atomic layer deposition
... the deposition tempera- ture and the compressive stress induced by handling for the examinations [12], and most importantly, the intro- duction of plasmas in the ALD process ...
9
Escape rate: a Lagrangian measure of particle deposition from the atmosphere
... wet deposition in the form of ...wet deposition process remains a subject for future work within the RePLaT ...escape rate provides an estimate of the average residence time of typical ...escape ...
15
Airflow and Micro-Particle Transport and Deposition in Realistic Lung Airways including the Alveolar Region
... particle deposition is ...(and deposition) of particles from (n-1)i+1 to ni after reading the corresponding initial particle information, where i is the order of a ...
224
Plasma Assisted Chemical Vapor Deposition of Titanium Oxide Layer at Room Temperature
... the deposition, the reactor was cleaned by oxygen gas plasma excited by 100 W rf-power with closing shutter settled above substrate to remove residual gases such as adsorbed water on the inner wall, then the ...
7
Applications of Atmospheric Plasmas
... encourages deposition uniformity by slowing depletion of species in the deposition zone, but results in slower deposition rates ...and deposition rates are increased by increasing the ...
292
Hybrid HIPIMS and DC magnetron sputtering deposition of TiN coatings: Deposition rate, structure and tribological properties
... plasma deposition environment although the resultant deposition rate is significantly ...sputtering deposition of a TiN hard coating on a hardened steel substrate, to investigate the effect of ...
12
Sizing Aerosol Particles Between One and Three Nanometers
... flow rate in the excess outlet results in a correspondingly high Reynolds number in this region and presents the main limitation to increasing the sheath flow ...
277
Recent trends in research on heavy-metal contamination in the sea
... Aspects of contamination which are considered include the input of metals to the sea and their deposition in the sediments, the influence of environmental and biological factors on[r] ...
20
Modeling The Physiologically-Based Variations For Inhalational Anthrax
... Inhalational anthrax follows deposition into alveolar spaces of spore-bearing particles in the 1 to 5µm range (Kohout et al., 1964), macrophages then ingest the spores, some of which are lysed and destroyed. ...
13
The Analysis of the Deposition Rate for Continuous Micro-Anode Guided Electroplating Process
... the deposition rate of the copper micro-column length is linearly growing with ...fastest deposition rate of its length is obvious at voltage ...
12
Blechinger, Julia (2012): Nanoparticles and human health: development and application of an experimental strategy to estimate cytotoxicity of nanopaticles. Dissertation, LMU München: Fakultät für Chemie und Pharmazie
... nanoparticle deposition on the cellular membrane and therefore to long contact times between the nanoparticles and the ...The influence of sedimentation and diffusion on cellular uptake was previously ...
142
Nitrification of Reactively Magnetron Sputter Deposited Ti Cu Nano Composite Thin Films
... potential interest in magnetron sputter process rely on the possibility of producing thin films with new properties, markedly different from those of corresponding equilib- rium bulk phases when one considers a ...
8