• No results found

injection Mold Design

Automatic Recognition and Construction of Draft Angle for Injection Mold Design

Automatic Recognition and Construction of Draft Angle for Injection Mold Design

... and design, Turng et al . [17] devel- oped a plastic injection mold knowledge management system, and built it in a network, using information technology to overcome geographic location and time ...

16

Plastic Flow Analysis & Simulation of Automobile Brake Light Lens with Optimum Injection Mold Design

Plastic Flow Analysis & Simulation of Automobile Brake Light Lens with Optimum Injection Mold Design

... of injection moulding, the time steps were controlled for both flow and thermal simulation by local flow information, and then the computing complexity analysis was ...

5

A wax injection mould design system

A wax injection mould design system

... The injection mold design is critically important to product quality and efficient product ...processing. Mold-making companies, who wish to maintain the competitive edge, desire to shorten ...

8

Design of Spoon Mold using Flow Analysis and Higher End Design Software

Design of Spoon Mold using Flow Analysis and Higher End Design Software

... plastic injection molding design contains a plastic part design, a mold design, and a design of injection molding process, all of which subsidize to the quality of the ...

6

Research of Heat Transfer Enhancement with Corrugated Conformal Cooling for Injection Mold Based on Fluent

Research of Heat Transfer Enhancement with Corrugated Conformal Cooling for Injection Mold Based on Fluent

... The formed radial flow and vortex enhances the mixture of the fluid in the mainstream and the wall, which increases the turbulent area of the fluid and reduces the thickness of the boundary layer of the wall, and the ...

10

Mold EEK! MOLD! HELP! What is Mold? What is Mold? What is Mold? Spore Lifecycle. Tara Kennedy Preservation Consultant

Mold EEK! MOLD! HELP! What is Mold? What is Mold? What is Mold? Spore Lifecycle. Tara Kennedy Preservation Consultant

...  All molds pose a health risk and some people are. more at risk than others[r] ...

11

Improving the 
		injection molding of small optical elements by integrating reverse 
		engineering and mold flow analysis

Improving the injection molding of small optical elements by integrating reverse engineering and mold flow analysis

... curve comparison. For total surface comparison, the entire set of scanned points is compared with the reference data. Figure-6(a) illustrates one example of total surface comparison between the scanned points of part and ...

6

A 3D Numerical and Empirical Study on the Effects of Injection Pressure and Temperature on the Quality of Produced Mold

A 3D Numerical and Empirical Study on the Effects of Injection Pressure and Temperature on the Quality of Produced Mold

... of Injection Temperature and Pressure for the Weld-lined Sample of PP At 170°C as the lowest considered temperature range of PP, viscosity has its maximum value; therefore, the flow shear rate is ...the ...

8

Design And Fabricate Mold For Polymer Based Interlocking Tiles

Design And Fabricate Mold For Polymer Based Interlocking Tiles

... Although ceramic tiles installation can be done by certain individual, it takes technical skills such as measuring to draw layout for floor design, mark reference lines and test corners for square. After all the ...

24

Design And Analysis Of Gating In Plastic Paper Clip Mold

Design And Analysis Of Gating In Plastic Paper Clip Mold

... Paper clip is commonly used by student and also officer to hold sheets of paper together. There are various type of paper clip which is different in material, size and shape. This project is about studying the ...

24

Design And Development Of Wooden Mold Base For Educational Kits

Design And Development Of Wooden Mold Base For Educational Kits

... In mold design subject, the current technique is applied to understand mold structure is through multi-media equipment, illustration from the book and explains from ...of mold on the podium, ...

24

Design And Analysis Of Casting Mold Using CAD Tool

Design And Analysis Of Casting Mold Using CAD Tool

... This report is submitted to the faculty of Manufacturing Engineering of UTeM as a partial fulfillment of the requirements for the degree of bachelor of Manufacturing Engineering (Manufacturing Design) with ...

24

OPTIMISATION OF PROCESS PARAMETERS IN LINEAR RUNNER FAMILY INJECTION MOLD USING MOLDFLOW SIMULATION SOFTWARE

OPTIMISATION OF PROCESS PARAMETERS IN LINEAR RUNNER FAMILY INJECTION MOLD USING MOLDFLOW SIMULATION SOFTWARE

... stated injection molding process is a rapid process when comparing with other type of molding ...this injection machine works by injecting molten thermoplastic into a mold ...plastic injection ...

8

Design Of Casting Mold For Natural Fiber – Metal Matrix Composite Material

Design Of Casting Mold For Natural Fiber – Metal Matrix Composite Material

... This research entitled “Design of Casting Mold for Natural Fiber-Metal Matrix Composite Material”. Generally this chapter provides information about background, problems statement, objective and scopes of ...

24

Design And Optimization Of Runner And Gating Systems For The Permanent Mold Casting

Design And Optimization Of Runner And Gating Systems For The Permanent Mold Casting

... Casting can be used to produce a wide variety of product with complex shape and it only involves one major manufacturing method. Casting involves pouring molten metal in a mold cavity that configured to the shape ...

24

The Design of Mold Clamping Mechanisms with Two Dead-Position Configurations

The Design of Mold Clamping Mechanisms with Two Dead-Position Configurations

... of mold clamping mechanism is the goal pursued by manufacturers of blow-molding ...the mold clamping mechanism has only one dead-position configuration for the mold in the closed ...the mold ...

12

Optimization of Fuel Injection System Design Parameters

Optimization of Fuel Injection System Design Parameters

... that injection duration and timing have dif­ ferent influences on specific fuel consumption and on particulate, unburned hydrocarbon and NOx ...the injection pro­ cess ...optimum design procedures by ...

10

Significance of Mold Filling Analysis for Finding Optimal Gate Location in Injection Molding Process for Bobbin.

Significance of Mold Filling Analysis for Finding Optimal Gate Location in Injection Molding Process for Bobbin.

... The Plastic adviser Software is one of software used to ensure the best choice location of feeding system and size of gate, runner and sprue. It's one of the most advanced tools ever devised for the plastic ...

8

Study And Analysis The Effectiveness CAD-CAM  System In Mold Design

Study And Analysis The Effectiveness CAD-CAM System In Mold Design

... aided design, which is use to drawing, design and drafting a product using ...are design using CAD technology. CAD system using geometrical design parameter helps the designer to view product ...

24

Design and simulation of investment casting mold for obsolete automotive part

Design and simulation of investment casting mold for obsolete automotive part

... casting mold does not take places before the investment casting processes are ...casting mold must be done before going through with the production of the product to make sure the best product from the ...

24

Show all 10000 documents...

Related subjects