• No results found

Injection molding of plastics

Development of a Two-stage Extruder-Injection Molding Machine for Manufacturing of Plastic Lumber Using Commingled Waste Plastics

Development of a Two-stage Extruder-Injection Molding Machine for Manufacturing of Plastic Lumber Using Commingled Waste Plastics

... Waste Plastics into useable plastic lumber as a product, and to realize the concept of Upcycling, where the transformation of old mixed waste plastic materials into a useable plastic lumber product of higher ...

6

USTOM INJECTION MOLDING. Together we will make the impossible.

USTOM INJECTION MOLDING. Together we will make the impossible.

... Over half of Plastikos employees are trained under and report directly to the Quality Manager, therefore providing the highest level of quality and service to our customers. Plastikos is a pioneer in adopting the Global ...

12

Design and Fabrication of Mini Injection Molding Machine

Design and Fabrication of Mini Injection Molding Machine

... B. Sha, S. Dimov, C. Griffiths, M. Packianather (2007) [4] conducted design of experiments and data analysis in Micro Injection Molding (MIM). They focused on the analysis with three factors barrel ...

7

A Modified Vince Gingery Plastic Injection Molding Machine

A Modified Vince Gingery Plastic Injection Molding Machine

... This machine lets me make plastic parts at a very low cost. Rather than spend many dollars for cold mixed plastics that can then be formed into the desired shape, I can use recycled plastic. Even “virgin” plastic ...

13

Improving the Performance of 3D Printed Molds for Plastic Injection Molding

Improving the Performance of 3D Printed Molds for Plastic Injection Molding

... The box is a temperature-controlled oven capable of creating and maintaining temperatures up to 260 degrees C. This temperature limit is suitable for injection molding of common plastics such as ...

6

Numerical Study On The Heliacal Cooling Channel For Injection Molding Process

Numerical Study On The Heliacal Cooling Channel For Injection Molding Process

... Injection molding is one of the most widely used processing technologies in the plastics industry ...plastic injection molding [4, 5]. In the injection molding field, the ...

6

Injection Molding Machines Benefit from

Injection Molding Machines Benefit from

... the plastics processing industry is striving to continually reduce overall manufacturing ...goal, plastics processors focus on four keys: energy-saving, materials savings, integration of additional ...

8

Development of flax fiber-reinforced polyethylene biocomposites by injection molding

Development of flax fiber-reinforced polyethylene biocomposites by injection molding

... automotive, plastics, and other industries (Mallick 1988) because they could offer either comparable to or better strengths than traditional pure polymer ...the plastics industry, automobile, and packaging ...

268

MODELLING AND MONITORING IN INJECTION MOLDING

MODELLING AND MONITORING IN INJECTION MOLDING

... Second, plastics shrink significantly when cooled. Together these properties indicate the need for the packing stage during the molding cycle. After the mold cavity is filled, continued pressure on the ...

155

Material Flow Data for Numerical Simulation of Powder Injection Molding

Material Flow Data for Numerical Simulation of Powder Injection Molding

... Different powder characteristics of Catamold 316LA and 316LG are also reflected in the flow properties of the two feedstocks. For 316LA whose particle size distribution is bimodal, a change in flow characteristic was ...

8

The influence of injection molding parameter on properties
of thermally conductive plastic

The influence of injection molding parameter on properties of thermally conductive plastic

... The injection machine specification are; screw diameter of 19 mm, injection capacity of 14 cm³, injection rate 20% and injection pressure of 60% to ...the injection molding ...

10

Synchronized Injection Molding Machine with Servomotors

Synchronized Injection Molding Machine with Servomotors

... The performance of the closed loop pressure with the proportional gain Kp = 2.0 is show in Fig. 8. At the beginning of the cycle , the output pressure cannot track the pressure command but when time goes on nearly ...

6

SHRINKAGE CONTROL OF POLYPROPYLENE DURING INJECTION MOLDING IN AL6061 TUBE

SHRINKAGE CONTROL OF POLYPROPYLENE DURING INJECTION MOLDING IN AL6061 TUBE

... by injection Molding machine into the aluminum tube which is covered two ends with clamps in which a clamp is having hole to flow the molten polymer and another clamp is fully covers the end of ...by ...

12

Injection Molding of Mechanical Alloyed Ti Fe Zr Powder

Injection Molding of Mechanical Alloyed Ti Fe Zr Powder

... the injection molding of mechanical alloyed Ti ­ Fe ­ Zr ...alloys. Injection molded samples were produced using mechanical alloying based on hydride-dehydride (HDH) titanium and pure iron and ...

6

Optimization Of Injection Molding Process On Name Tag Plastic Product

Optimization Of Injection Molding Process On Name Tag Plastic Product

... of injection moulding, and also reviewed the topics such as injection moulding process, plastic defects, plastic material, Taguchi method and part ...

24

ANALYSIS OF INJECTION MOLDING PROCESS TO REDUCED DEFECTS (SHORT-SHOT)

ANALYSIS OF INJECTION MOLDING PROCESS TO REDUCED DEFECTS (SHORT-SHOT)

... Cite This Article: L. D. Mahajan, and P. N. Ulhe (2018). “ANALYSIS OF INJECTION MOLDING PROCESS TO REDUCED DEFECTS (SHORT-SHOT).” International Journal of Engineering Technologies and Management Research, ...

7

Reverse Engineering Of Hand Phone Housing Plastic Injection Molding

Reverse Engineering Of Hand Phone Housing Plastic Injection Molding

... This reverse engineering of hand phone housing plastic injection mold is done due to its advantages in reducing production cost and to shorten the development process. The reverse engineering is a process that ...

24

A Comparative Study of Coolants Based on the Cooling Time of Injection Molding

A Comparative Study of Coolants Based on the Cooling Time of Injection Molding

... The objective of injection mold design is to reduce the cooling time. There are a number of factors affecting cooling time. Here, factors linked to cooling time are listed in brief in Figure 2 to serve as the ...

5

Kansei Engineering Applied to the Form Design of Injection Molding Machines

Kansei Engineering Applied to the Form Design of Injection Molding Machines

... This study investigated the relationship between a subject’s evaluation of injection molding machines (IMMs) and for- mal design features using Kansei engineering. This investigation used 12 word pairs to ...

11

Numerical Study on Flow Length in Injection Molding Process with High-Speed Injection Molding

Numerical Study on Flow Length in Injection Molding Process with High-Speed Injection Molding

... the injection molding process was finished, the part will be rejected, then, the melt flow length will be ...The injection speed conditions were selected as 100, 500, 1000, and 1400 mm/s, and the ...

6

Show all 3405 documents...

Related subjects