Inlet angle
Cervical kyphosis in patients with Lenke type 1 adolescent idiopathic scoliosis: the prediction of thoracic inlet angle
... AIS: Adolescent idiopathic scoliosis; AUC: Area under the curve; CK: Cervical kyphosis; CL: Cervical lordosis; HRQOL: Health-related quality of life; LIV: Lower instrumented vertebra; LL: Lumbar lordosis; NT: Neck tilt; ...
8
A Review for Materials Used in Gas Turbine Blades
... blade inlet angle may differ greatly from hub to tip which will expose the blade to high mechanical stresses, and nowadays it is more common to apply a non-free vortex design (non constant work distribution ...
5
Aerodynamic Optimization of a Centrifugal Fan Using Response Surface Methodology
... Centrifugal fan, a widely used centrifugal machinery, plays an important role in industry. The centrifugal impeller is the key component of the centrifugal fan and it has a significant effect on the performance of the ...
14
Experimental Analysis of Flow through Rotating Swirler with Effect of Guide Vane
... vane angle 45° is made in transparent perspex ...an inlet pipe of length 350 mm, 120 mm outer diameter and hub diameter of 40 ...design, Inlet pipe consist of rotating swirler of 8 blades at 0° ...
7
Theoretical, Experimental and Numerical Investigations of the Effect of Inlet Blade Angle on the Performance of Regenerative Blowers
... four inlet flow angles (90˚, 115˚, 125˚ and 135˚) of the blade at outlet flow angle of 90˚ on the performance of regenerative blower at rotation speed of 3000 rpm and at different flow ...one inlet ...
14
Optimizing Nozzle Geometry of Dry Ice Blasting Using CFD for the Reduction of Noise Emission
... particle inlet angle increase slightly with increase further increase of nozzle particle inlet ...particle inlet angle. It was found that increase particle inlet angle ...
6
Fabrication and characterization of dexibuprofen nanocrystals using microchannel fluidic rector
... (5 mg/mL) and polymers dissolved in aqueous phase were introduced into MCFR (inlet angle 10 ° with internal diam- eter of 0.5 mm) at a flow rate 0.5:2.0 mL/min, respectively. Then, the emergent ...
10
Review Of Optimization Of Mixed Flow Impeller Using Computational Fluid Dynamics
... and inlet angle of blade changes head of ...varying angle of blades and number of blades, head value of mixed flow impeller is ...(van angle) are fixed for ...vane angle is achieved in ...
7
A REVIEW ON NOZZLE WEAR USING CFX ANALYSIS IN ABRASIVE WATER SUSPENSION JET MACHINING
... Nozzle wear is the result of the process of material removal as the two surfaces are in sliding contact. The study of parameters that influence the nozzle wear are nozzle length, nozzle diameter, nozzle inlet ...
6
A Review of Vortex Tube Refrigeration System
... tangential inlet nozzles, an axial tube with a vortex chamber, a cold gas outlet and a hot gas ...the inlet nozzles. As the air accelerates through the inlet nozzles, it exits into a cylindrical ...
6
The Choice of Appropriate Scenario in Order to Reduce the Effect of Thermal Pollution at the Damietta Branch Caused by Cooling Water Discharged from Kafr Al Batek Power Station
... discharge angle of the existing ...discharge angle from 90 ˚ to 120˚ and ...the inlet and the outlet is 412 m and the outlet di- mensions is 9-m width and 3-m ...the inlet of the station ...
10
Dual baffle system in automatic air inlets for livestock facilities
... air inlet. The two baffles are hinged at the top and bottom of the inlet respectively and the opening between the baffles is allowed to increase or ...
19
Experimental and CFD Studies on the Effect of the Jet Position on Mixing Performance
... In all cases the nozzle and suction were set at a constant height of 5 cm from the tank bottom and the jet angle was fixed at 22.5º with respect to horizon. In all of the experiments, after the flow stabilization ...
10
Performance Evaluation of A Steam Turbine Test RIG and Oil Fired Boiler
... The steam turbine obtains its motive power from the change of momentum. When steam jet strikes the blade it exerts a pressure on the blade, when centrifugal force acts on the blade normal to the blade angle along ...
11
Inlet Shroud Angle of a Shrouded Wind Turbine
... International Journal for Research in Applied Science & Engineering Technology IJRASET The profile is changed at 30˚ to get better augmentation.By introducing a NACA 4481 aerofile profil[r] ...
10
Effect of Reynolds Number on Aerodynamic Characteristics of an Airfoil with Flap
... for angle 14 0 are shown in the Figures 23 and ...at angle of attact 15 in the Figures 25 and ...the angle of attack increases the region of the negative pressure tends towards the leadind edge and ...
14
Effect of gravity and gas flow direction on the operation of Polymer Electrolyte Membrane Fuel Cells
... During fuel cell operation, liquid water is formed by the reactions occurring in the cathode catalyst layer. The water then flows from the upper side to the bottom side of the flow field due to the gravity effect. When ...
22
Analysis of Flow Through Rotameter Using CFD
... With these available dimensions the 2D axisymmetric rotameter model is constructed using ANSYS Design Modeler. In the stimulation process, the grid generation plays a vital role for better accuracy and stability in the ...
8
Study on Separation Characteristics of Dust and Droplet on Air Intake Pre filtration Systems of CV Based on CFD Simulation and Test
... high inlet pipe (also known as the air intake pre- filtration Systems) mainly includes the vortex pipe, the dust and droplet drain valve, the shock absorption bellows, and the assembly pipeline with four parts of ...
8
International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal Volume 7, Issue 10, October 2017)
... the inlet pressure, rotor blade ...at inlet the velocity component is not correctly achieved for the stated design condition and more of turbulence at higher pressure and below choked condition of mass flow ...
6