inlet/outlet configuration
Acoustical Performance of Pure Reactive Muffler with Central Inlet and Central Outlet Configuration
... The transfer matrix method (TMM) use the transfer matrix of a muffler element as a function of the element geometry, state variables of the medium, mean flow velocity, and properties of duct liners, if any [5]. The TL ...
6
The optimization of inlet and outlet port locations of a vented square cavity
... the inlet and outlet ports are ...an inlet port in the left side of the cavity and exits from the opposite ...optimum inlet/outlet configuration has been selected based on the ...
11
Inlet and outlet configurations effect on thermal comfort
... Conditioning (HVAC) system can be resolved by using chilled ceiling systems which have highly potential to resolve it. In this project, I value more focus on vary the ventilation configuration of air inlet ...
24
Flow measurements in the discharge port of a screw compressor
... presented and compared in figure 9. The results presented in figure 9(a) and (b) refer to male and female rotors, respectively, upstream the W-section, while figure 9(c) and (d) refer to the discharge port close to the ...
16
CHARACTERIZATION AND FEASIBILITY OF A PORTABLE OXYGEN CONCENTRATOR FOR USE WITH A MASS CASUALTY VENTILATOR
... PSI inlet pressures, very near the middle setting flow rate for 15 PSI, and then again getting closer to the maximum flow rate for the inlet pressures of 20 and 25 ...
95
SPH-DEM approach to numerically simulate the deformation of three‑dimensional RBCs in non‑uniform capillaries
... The deformation behaviour of the RBC is examined when the RBC is subjected to a linear shear flow. In order to generate the linear shear flow, the RBC is placed into the plasma domain within a rectangular flow channel ...
22
Boiler Drum Parameter Optimization by Fuzzy PID Control Technique
... Steam utilization process in boiler invokes three parameters which need the control. First controlled parameter is the water level in the drum. Steam generation consumes the water and water level keeps on changing and ...
6
Effect of Geometric Configuration on Performance of Uniflow Cyclone
... angles, outlet to inlet diameters ratio, separation lengths and inlet velocities on uniflow cyclone ...of inlet velocities, Outlet to inlet diameter ratio, separation length and ...
7
Experimental Investigation on Air Leakage Characteristics of Containments
... at inlet/outlet and flow meters at ...at outlet. The pressurized air is injected into inlet of the air chamber and the pressure is ...at outlet is ...at inlet gets higher, air ...
7
Investigation of turbulent flow characteristics within screw compressor
... Figures 3(a) and (b) represent the axial RMS velocity variation at the outlet of the discharge port and correspond to those at Figure 2 (c) and (d). In general the RMS velocity profiles follow those of the mean ...
5
Performance investigation of turning diffusers at various geometrical and operating parameters
... Despite extensive literature on diffusers are available, less attention has been given to 3-D diffuser type [2, 19, 20]. A 3-D turning diffuser is used widely in industrial flow particularly in HVAC and wind tunnel ...
22
design and Analysis of a Heat Exchanger Network
... temperature while keeping the hot fluid inlet temperature constant, heat transfer rate decreases. The result of the study ends up with the final conclusion that the effectiveness of the heat exchanger depends on ...
7
Performance Calculation of Vehicle Radiator Group using CFD
... 6) Mesh generation: The entire face is divided into innumerable small finite number of elements. This process is called meshing and the grid generated is called a mesh. Meshing gives us a scope to study the behavior of ...
14
Evaporation of stationary alcohol layer in minichannel under air flow
... A series of three experiments has been executed. As a working fluid we used ethanol (GOST R 51723-2001), as gas – air. Gas flow entering the test cell is varied from 100 to 500 ml/min every 100 mL/min. Temperature of the ...
5
Paper 08-2011-1
... As we discussed before Figs 7.a and 13.a show that concentrations in both reservoirs at the end of FE simulation are the same, which demonstrates accuracy of our numerical procedure and implementation into our software ...
15
A combined experimental-numerical approach for two-phase flow boiling in a minichannel
... the inlet and outlet, pressure at the inlet, pressure drop along the minichannel length, the power of the electrical current flowing through the heater; recording the temperature distribution on the ...
8
Application of Bionics of Tiger Beetle to Aerodynamic Optimization of MIRA Fastback Model
... Parameters Value or model Inlet boundary Velocity inlet, v=30m/s Outlet boundary Pressure outlet, p=0 Ground Fixed ground Sides Fixed ground Body surface boundary Fixed ground, reference[r] ...
10
A computer aided measurement method for unstable pelvic fractures based on standardized radiographs
... the inlet radiographs, which could be considered as the external or internal rotation of the displaced hemipelvis around the axis across the centre of the sacrum and perpendicular to the inlet ...
10
Inlet outlet arrangement effects on ice bath cooling system for athlete's injury recovery procedure
... As it takes quite a long time to reduce the temperature, this technology is considered too inefficient for its purpose. Futhermore, the price is relatively expensive. The objective of this study is to investigate the ...
5
Design and testing of a 6 inch control Valve with a Multi stage Anti cavitation trim
... the inlet, the regions of increases velocity radiate out from the center of the ...over outlet portion in an elipse form or a ...the outlet tries to carry fluid with it towards the outlet, ...
149