• No results found

Plastics - Molding

Development of a Two-stage Extruder-Injection Molding Machine for Manufacturing of Plastic Lumber Using Commingled Waste Plastics

Development of a Two-stage Extruder-Injection Molding Machine for Manufacturing of Plastic Lumber Using Commingled Waste Plastics

... Waste Plastics into useable plastic lumber as a product, and to realize the concept of Upcycling, where the transformation of old mixed waste plastic materials into a useable plastic lumber product of higher ...

6

Estimation of Injection Molding Process for a Thin Fresnel lens By Plastic Flow Simulation

Estimation of Injection Molding Process for a Thin Fresnel lens By Plastic Flow Simulation

... Solidworks Plastics module of Solidworks is used for the plastic flow simulation of a thin Fresnel ...injection molding can affect these dimensional parameters and so the desired ...injection molding ...

7

DESIGN & DEVELOPMENT OF IMPROVED PLASTIC BAFFLE FOR COST EFFECTIVENESS

DESIGN & DEVELOPMENT OF IMPROVED PLASTIC BAFFLE FOR COST EFFECTIVENESS

... Injection molding has been a challenging process for many plastic components manufacturers and researchers to produce plastics products meeting the requirements at very economical ...injection ...

9

Thermoplastic forming and related studies of the supercooled liquid region of metallic glasses

Thermoplastic forming and related studies of the supercooled liquid region of metallic glasses

... injection molding. A simple injection molding process requires feedstock material, a heated reservoir in which the material is softened, a nozzle, a mold and a plunger to force the softened material from ...

40

Integrated analyses in plastics forming

Integrated analyses in plastics forming

... involving plastics moulding is begun, a design engineer starts with a conceptual design of the part, decides which plastics material will be used and chooses a machine basing his ideas on simple ...

257

Production Planning at Dupo Plastics

Production Planning at Dupo Plastics

... Cost Orders finished late Orders finished ahead Orders finished on time Planned order execution time Average lead time Planned setup time Planned runtime per item Downtime Planned produc[r] ...

98

Effect of Elevated Temperature on Mechanical Properties of Waste Polymers Polyethylene Terephthalate and Low Density Polyethylene Filled Normal Concrete Blocks

Effect of Elevated Temperature on Mechanical Properties of Waste Polymers Polyethylene Terephthalate and Low Density Polyethylene Filled Normal Concrete Blocks

... 100 mm cubes were casted and utilized for the test elevated temperatures on the compressive strength of the concrete blocks. The concrete with zero plastics served as the control sample while the plast-crete (s) ...

8

Epoxy compound and polystyrene sheet combined decoratively with wood

Epoxy compound and polystyrene sheet combined decoratively with wood

... commercial Chemical of are about production companies modern it supersedes or more " old materials until at distinct plastics today by some 5 produced these new plastics, of companies 40[r] ...

60

Application of restaurant waste lipids (RWL) as a binder component in metal injection moulding

Application of restaurant waste lipids (RWL) as a binder component in metal injection moulding

... Powder injection moulding (PIM) which consists of metal injection moulding (MIM) and ceramics injection moulding (CIM) is one of the major manufacturing processes used to generate small parts with intricate geometries, ...

75

“A Comparative Evaluation of Palatal Adaptation in Denture Bases Processed With Compression Molding and Injection Molding In Two Different Palatal Configuration”-An In Vitro Study

“A Comparative Evaluation of Palatal Adaptation in Denture Bases Processed With Compression Molding and Injection Molding In Two Different Palatal Configuration”-An In Vitro Study

... Injection molding denture base was statistically higher, when compared to the compression molding denture base 8 ...Injection molding technique the resin was pushed through the flask continuously for ...

8

PLASMA GASIFICATION OF WASTE PLASTICS

PLASMA GASIFICATION OF WASTE PLASTICS

... of plastics pyrolytic processing (eventually with plastics waste as a target material to be processed) the material to be pyrolysised was polyethylene (PE) with the grains smaller than 500 ...

7

Flow behaviour to determine the defects of green part in metal injection molding

Flow behaviour to determine the defects of green part in metal injection molding

... Binder should posses a lower viscosity than feedstock. The viscosity of MIM feedstock is quite higher than that of binder because of the high volume fraction of powder particles. At injection molding temperature, ...

6

Screening and production of biodegradable plastics from marine Bacillus spp

Screening and production of biodegradable plastics from marine Bacillus spp

... Plastic is considered an individual gift of modern science and technology to mankind. Nowadays, plastics and synthetic polymers are mainly produced from petro chemical elements, which do not decompose, thus ...

6

Decomposition of Mould Resin in Spent Capacitors by NaOH for the Recovery of Tantalum

Decomposition of Mould Resin in Spent Capacitors by NaOH for the Recovery of Tantalum

... In our previous studies, we showed that acrylonitrile butadiene styrene (ABS) resin plastics used in computer casing plastics could be decomposed upon pyrolysis wi[r] ...

5

Improving the Facility Layout Design in Aqua Dire Purified Mineral Water Factory: A Case Study

Improving the Facility Layout Design in Aqua Dire Purified Mineral Water Factory: A Case Study

... arrange, locate and distribute the machines, departments , equipment and support services in a manufacturing facility to achieve minimization of overall production time, maximization of operational and arrangement ...

6

Systematic Development Of Injection Mold : A Convocation Souvenir

Systematic Development Of Injection Mold : A Convocation Souvenir

... produce molding of inferior quality and less cost effective than may have been ...injection molding is based on the type of artifact, hence the numbers of trials are required to understand like injection ...

24

Influence of Continuous Use of a Vacuum Forming Machine for Mouthguard Thickness after Thermoforming: Effect of the Time Interval between Repeat Moldings

Influence of Continuous Use of a Vacuum Forming Machine for Mouthguard Thickness after Thermoforming: Effect of the Time Interval between Repeat Moldings

... next molding, this heat affects the softening of the ...consistent molding, but the temperature of the forming device gradually increases from one molding to the ...

9

Fly Ash an Alternative for Molding

Fly Ash an Alternative for Molding

... Fly ash collected from Thermal power plant and graphite industries is an excellent alternative to molding sand for use in dry sand molds. Various analyses were done with fly ash mixed with molding sand. The ...

9

ALTERNATIVE CASTING METHODS FOR LARGE SIZED COMPONENT OVER SAND CASTING METHODS: A REVIEW

ALTERNATIVE CASTING METHODS FOR LARGE SIZED COMPONENT OVER SAND CASTING METHODS: A REVIEW

... M.A. Sellés [3] Analyses and reviews different tools to calculate the production economics in injection molding. This was done to make a small review of computer-aided software based mainly on the calculation of ...

6

Numerical Study on Flow Length in Injection Molding Process with High-Speed Injection Molding

Numerical Study on Flow Length in Injection Molding Process with High-Speed Injection Molding

... The material used was Acrylonitrile Butadiene Styrene (ABS), type PA-756, supplied by Chi-Mei. The experimental model was a spiral shape 6 mm long and 0.4 mm thick, as shown in Figure 1, and was used to measure the flow ...

6

Show all 605 documents...

Related subjects