Shear bond strength testing of the samples
SHEAR BOND STRENGTH TEST
... a fixed sleeve to hold one side of the specimen and to provide a reaction force; and a sliding sleeve holding the other side of the specimen that moves perpendicular to the specimen’s vertical axis and produces the ...
5
An investigation into the shear bond strength of masonry
... 65 to the bricks. Hence these positions become the weakness planes of a wall exposed to shear forces. In conclusion the failure patterns above have shown that failure pattern 1 is the most probable failure pattern ...
121
Interface shear strength of composite concrete-to-concrete bond
... and shear strength of composite slab by increasing the effective ...flexural strength of the composite slab may reduce if the components are not acting ...interface shear strength ...
52
Comparison of internal bond strength and compression shear strength of wood-based materials
... In this study, a compression shear (CS) method was de- veloped for collecting shear strength data of wood-based materials, and the results were compared to the [r] ...
6
The Effect of Temperature on Shear Bond Strength of Clearfil SE Bond and Adper Single Bond Adhesive Systems to Dentin
... [9] It was reported that pre-heated self-etching adhe- sives would reduce the bond strength. It has also been reported that higher temperature can elevate the vapor pressure in solution and enhance the ...
7
The Shear Bond Strength of Porcelain Laminate to Prepared and Unprepared Anterior Teeth
... Figure 4: Different modes of failure, a: Adhesive failure, b: Cohesive failure Discussion The present in vitro study used three different prepara- tion methods and compared the fracture toughness of laminate porcelain ...
6
Influence of resin-tags on shear-bond strength of butanol-based adhesives
... micro-shear bond strength (µSBS) of tertiary- butanol-based adhesive under moist and dry conditions and correlate the results to resin-tags ...µSBS testing, while 2mm composite-resin was ...
9
Evaluation of Shear Bond Strength of the Composite to Biodentine with Different Adhesive Systems
... Single Bond (group 2), one step self-etch strategy Clearfill ® SE Bond (group 3) and the control group (group ...matrices. Shear bond strength was measured by means of a universal ...
6
Effect of 2% Chlorhexidine on Shear Bond Strength of Composite Resins to Dentin
... Materials and Methods: In this in-vitro study, 60 intact extracted human premolars were utilized. Each tooth was sectioned vertically and dentin of the buccal surface was exposed. Then, specimens were divided into six ...
5
Effect of enamel protective agents on shear bond strength of orthodontic brackets
... containing 5% sodium fluoride. Fluoride was found to be effective in reducing the development of white spot le- sions associated with fixed orthodontic treatment [16,24]. Also, ICON resin infiltration was found to de- ...
6
Shear bond strength of metallic brackets bonded with a new orthodontic composite
... The conventional use of adhesive composites requires well-de- fined steps in order to assure adequate adhesion to enamel. Elimina- tion of one of these steps without compromising the adhesiveness would facilitate the ...
5
Shear Bond Strength of Orthodontic Brackets to Composite Restorations Using Universal Adhesive
... acceptable bond strength values [3, 9, 12, ...mean shear bond strength values of ...lowest bond strength was noted following the use of hydrofluoric ...on bond ...
8
The Effect of CuO Nanoparticles on Antimicrobial Effects and Shear Bond Strength of Orthodontic Adhesives
... and bond strength of orthodontic ...trans- bond XT at concentrations of ...the shear bond strength, with each concentration of nano-composites as well as the control group ...
5
Shear bond strength of various luting cements to fixed prosthodontic restorative materials
... the strength of the restoration seems to be reduced ...low shear bond strength values among all ...the bond strength of cementing agents, the ceramic surface can be conditioned ...
10
Evaluation of Bond Shear Strength of Heat Treated Cu Al Bonding Interface
... study, samples with Cu wire bonded on pure Al bond pad metallization are successfully synthesized at 150°C, 280°C and ...the samples. Samples were then treated to HTS of durations 500 hours ...
8
The effects of dentine contamination on the shear bond strength of a self-etching adhesive and a nanocomposite
... 24 3.1.4 Blood Bleeding is a common complication of tooth preparation, particularly with large and /or subgingival cavities. This has been implicated in reduced bond strength. Red blood cells contain ...
90
Influence of bond and anchorage conditions of the shear reinforcement on the punching strength of RC slabs
... AlthoughȱtheȱuseȱofȱtransverseȱelementsȱisȱaȱcommonȱandȱwellȬestablishedȱsolutionȱtoȱenhanceȱtheȱ responseȱ ofȱtheȱ slabsȱ toȱpunching,ȱ theȱ activationȱ ofȱ thisȱ veryȱ specificȱ reinfo[r] ...
227
The effect of light curing tip angulations on the shear bond strength of an orthodontic adhesive
... the shear bond strength of each light curing unit was ...the bond strength ...lower shear bond strengths, with a significant reduction at a light-tip distance of six mm ...
6
Comparison of shear bond strength of three adhesive liners to nanocomposite: an in vitro study
... Dentine bond strength and microleakage of flowable composite, compomer and glass ...a bond between two resin layers,flowable composite is expected to bond well with the more viscous resin ...
5
Comparative Study of Shear Bond Strength of Three Veneering Ceramics to a Zirconia Core
... The samples were then mounted in the universal testing machine (Zwick Roell AG, Ulm, Germany) for measuring the shear bond strength between the veneers and the ...The shear force ...
6