steel and aluminum
GTAW of Zinc Coated Steel and Aluminum Alloy
... non-zinc-coated steel and A5052 aluminum ...1) steel fusion zone, 2) steel heat affected zone, 3) steel base metal zone, 4) aluminum fusion zone, 5) aluminum heat affected ...
11
Characterization of compressive damage behavior of steel and aluminum
... both steel and aluminum ...of aluminum specimens with thickness ...for aluminum specimen with thickness of ...for steel specimens with thickness ...
20
Simulation and Optimization Studies on the Ring Rolling Process Using Steel and Aluminum Alloys | Journal of Engineering Sciences
... ed based on comparison and observational validation. To simulate the non-linear problem that characterizes the ring rolling process, finite element codes are available [4]. The analysis is done using ANSYS. The ...
5
Powder Metallurgical Fabrication and Microstructural Investigations of Aluminum/Steel Functionally Graded Material
... in aluminum reduction cell for the purpose of welding alumi- num rod and steel bracket ...joining aluminum and steel at the electric transition joints have the drawbacks of cracking and ...
11
Processing and Characterization of Aluminum-Steel Composite Metal Foams
... only aluminum foam, or in combination with other materials such as steel tubing or aluminum ...castings. Aluminum foam (Cymat) is being used as filler material for tube structures that replace ...
251
Effects of Zn Based Alloys Coating on Mechanical Properties and Interfacial Microstructures of Steel/Aluminum Alloy Dissimilar Metals Joints Using Resistance Spot Welding
... sidering aluminum-rich intermetalic compound (IMC) is also recognized between Al-Zn-coating and ...The steel plates and aluminum alloy plates were welded by resistance spot welding after cleaning the ...
7
Experimental Testing of Aluminum Foam Filled Stainless Steel Braided Tubes Subjected to Transverse Impact
... Preparation of foam filled braided tube specimens involved first cutting approximately 420 mm of braided manually compressed stainless steel tubing using conventional aviation shears. The mass of tubing utilized ...
153
Growth Manner of Intermetallic Compound Layer Produced at Welding Interface of Friction Stir Spot Welded Aluminum/Steel Lap Joint
... is aluminum and the lower part is steel. The aluminum plate was deformed to trace the tool ...the aluminum matrix and the steel matrix close to the welding ...the aluminum close ...
7
Corrosion of Aluminum, Copper, Brass and Stainless Steel 304 in Tequila
... stainless steel (SS) pot stills [11, ...with aluminum nor brass equipment sections along the production line, tequila can be stored in vessels made of these materials so there is some interest for ...
11
STUDIES ON ELECTROMECHANICAL BEHAVIOR OF SMART STRUCTURES BY EXPERIMENT AND FEM
... The finite element code for analysis of smart structures is developed using MATLAB programming language. Also experiment was carried out on the smart beam with piezoelectric material attached and related instruments are ...
9
Experimental Investigations of Friction Welding using Aluminum With Mild Steel
... In recent years, the use of joints between dissimilar metals has considerably increased. In the development of new technologies for the aerospace, medical and automotive industries, these junctures are of high ...
6
Investigating the Effect of Copper Chromium and Aluminum Electrodes on EN-31 Die Steel on Electric Discharge Machine Using Positive Polarity
... Abstract Electric discharge machining (EDM) is a ‘newer technology utilized to machine hard metals, alloys, composites and ceramics. This paper reports the experimental investigation carried out on EDM to study the ...
5
Miniature mobile sensor platforms for condition monitoring of structures
... mild steel and aluminum, which contained a set of nine 3 × 1 cm artificial defects, varying in depth from 10% to 90% of total plate thickness and distributed equally with a spacing of 25 cm, as shown in ...
9
Study of the Door Closing Performance of an Aluminum Door
... a steel frame and for an aluminum frame, in order to be able to directly compare all the contributions that hinder or help the door closure and detect the factors that change the most with the change of ...
164
Structural Analysis of Isotropic and Orthotropic Beams and Plates in First Order Shear Deformation Theory
... For beams, the displacements are less for orthotropic materials Carbon Fiber and Glass Epoxy than isotropic materials Steel and Aluminum. The stresses are more for Carbon Fiber and Glass Epoxy than ...
11
DEVELOPMENT OF EXTENDED SURFACE HEAT TRANSFER EQUIPMENT AS LABORATORIES TEACHING AIDS
... mild steel and aluminum) to determine their respective temperature distribution along an extended surface over a length of 28 cm for 2700 seconds interval at different voltage of 50, 100 and 150 ...Mild ...
10
Download Download PDF
... of aluminum foam made from the addition of recycled ballistic aggregates to the foams of aluminum alloy powder in regular and random patterns through powder metallurgy ...of steel and aluminum ...
9
The Investigation and Discussion of Maintenance Situation of old Residences in Shanghai
... traditional steel windows are poor corrosion resistance, poor air tightness, poor water tightness, high thermal conductivity, and more loss in ...However, aluminum alloy windows have many advantages such as ...
5
Modeling & Analysis of a 100CC I C Engine Connecting ROD
... connecting rod in SOLIDWORKS 2018 software and doing static structural analysis in ANSYS WORKBENCH 19.2 software. Thus the part which is modeled is converted into igs file to import in ANSYS work bench and static ...
5
DYNAMIC CHARACTERSTIC ESTIMATION OF STRUCTURAL MATERIALS BY MODAL ANALYSIS USING ANSYS
... It is evident that the material damping is higher for Acrylic material and mild steel beams when compared to Aluminum and Brass for the adopted dimensions of the beam. It was observed during iterations that ...
8