steel material
A Review on Resistance Spot Welding of Steel Material
... between steel and aluminum could be achieved by using a transition ...of steel to aluminum by using a transition aluminum-clad steel ...of steel was an elliptical regular weld with dendritic ...
13
Steel, material flows, and globalisation: by-product optimisation and waste management in today's steel industry
... of material flows in a selection of modern steel plants, especially the gen- eration of wastes, from a social sciences ...a steel company’s ...a material and technological point of view, but ...
9
Design and Analysis of Leaf Spring with Different Arrangements of Composite Leaves with Steel Leaves
... two steel leaves are ...conventional steel leaves with additional ...three steel leaves instead of four leaves, gives better results than alternate arrangement of steel and composite ...
5
A Design Modification Approach to Utilize the Benefits of Metal Additive Manufacturing Adoption
... stainless steel material with integrated cellular design to manufacture a guide bracket found on a military ve- hicle via Selective Laser Melting process was ...stainless steel honeycomb as compared ...
7
Natural Convective Heat Transfer from Inclined Narrow Plates
... materials steel and aluminium when we applied700c ambient temperature and 7e-4 film coefficient on the top surface of the piston ...between steel and aluminium piston we can say the heat flux of existing ...
6
STUDIES ON EFFECT OF PERCENTAGE OF CARBON ON THE TENSILE & COMPRESSIVE STRENGTH OF STRUCTURAL STEEL
... The steel material used for this investigation is a medium carbon steel & mechanical properties investigated were, the tensile strength and ...of steel for a specific period of ...
6
Modeling, Analysis & Optimization of Parameters for Great Weld Strength of the Chassis for Off Road Vehicles
... M. U. Deshpande et al. (2016) [9] have focused on Optimization of GMAW Process Parameters to Improve the Length of Penetration in EN 10025 S 235 Grade. This work gives the detail influence of welding process parameters ...
9
Tensile Properties of AM Maraging steel
... maraging steel properties have been compared with wrought maraging ...maraging steel was much more ductile than expected and exhibited significant necking under all conditions ...wrought material, ...
6
Effect of low-cycle-fatigue damage on the strength and ductility of structural steel
... This study was undertaken to investigate the influence of LCF damage on the material behaviour of structural steel as discussed below. Series of material tests were undertaken in this [r] ...
202
Futures Trading In Rubber- Are The Stakeholders In Kerala Benefitted?
... When screw operated clamps are worn out the screw as well as the nuts need to be replaced. Generally screw are longer and costlier then nuts. So nuts are made of phosphor bronze which has high tensile strength. As ...
5
Design of a Crane Hook of Different Materials and Stress Analysis Using ANSYS Workbench
... Stainless steel 316(marine). Thus among the four materials used, Stainless Steel 316(marine) is least prone to plastic deformation which leads to failure of the ...Stainless Steel 316(marine) and ...
7
SteelConverter and Caltech VirtualShaker: Rapid Nonlinear Cloud Based Structural Model Conversion and Analysis
... the STEEL and Perform analyses will diverge and it is expected for some of the more realistically weighted buildings that the STEEL analyses will become unstable at a lower ...the STEEL pushover ...
321
Inhibiting Corrosion of Crown Corks of Fanta using an Eco Friendly Inhibitor
... The crown cork (also known as a crown seal, crown cap or just a cap), the first form of bottle cap, was invented by William Painter in 1892 in Baltimore. It is made of tinplate, electrolytically lined with tin, or TFS ...
6
GLOBAL JOURNAL OF ADVANCED ENGINEERING TECHNOLOGIES AND SCIENCES MATERIAL POWER INFLUENCE OF BUCKET TEETH EXCAVATORAISI 4140 USING ABRASIVE WEAR TEST WITH OGOSHI UNIVERSAL HIGH SPEED TESTINGMETHOD S. Hadi Suryo*, A.P. Bayuseno, J. Jamari, Herry Kiswanto
... research, the test uses Ogoshi Universal High Speed Testingmethod in which testing object is swiped with a 19.08 kg load from revolving disc with wear duration is 1 minute.Swipe loading will result a continuous contact ...
11
Analytical Method to Derive Overstrength of Dowel Type Connections
... The authors would like to acknowledge the Natural Hazard Research Platform and EQC of New Zealand for providing research grants for this project. XLam NZ Ltd is acknowledged for contributing to the experimental ...
12
Design & Analysis of Crankshaft by Forged Steel & Composite Material
... forged steel is 150 MPA and on composite material is 146 ...forged steel so due to the low cost of forged material, it’s almost used for ...
7
Characteristics of electrode materials on machining performance of tool steel SKD11 with EDM Shinking
... the material removal rate from the tool steel SKD11 is shown in ...electrode material plays a big role in productivity especially for the applied high pulse ...a material removal rate almost ...
6
Design, Analysis & Weight Reduction of Shell of Refrigerator Compressor
... Optimization was achieved on Shell of compressor. Some of components of system like motor assembly and vents are kept as it is due to its proper design. Design calculations, analysis model, and optimized system are ...
9
MATERIAL SELECTION AND TESTING OF HACKSAW BLADE BASED ON MECHANICAL PROPERTIES
... We have taken cutting time for same diameter jobs of above materials so we can find about the relative cutting performance. Here 25 mm Diameter of work piece is taken for being cut , this 25 mm round cross section is ...
10
Suitability of technical materials for machinery subsoilers for soil tillage
... original material by Gregoire Besson ...this material to the multifunctional part of the body is greatly restricted by its mightiness, which leads to an enormous increase in tensile ...tool steel was ...
8