Structural Identification and Finite Element Model Updating
Vibration-based finite element model updating and structural damage identification
... to structural failure with unknown consequences. Structural health monitoring strategy based on vibration measurements for existing aging structures offers a promising technique for effectively managing the ...
292
Accurate structural identification for layered composite structures, through a wave and finite element scheme
... The structural parameters to be identified are the Young’s modulus of the facesheet and the shear modulus of the core in the direction of wave ...the identification criterion. If the identification ...
26
Finite element model updating of bolted lap joints implementing identification of joint affected region parameters
... simple model which can simulate the dominating physics of a bolted joint is very important in modeling of large and complex ...this model are identified by minimizing an objective ...an updating ...
14
Finite Element Of Human Spine CAD Model Analysis
... Finite Element is the best method can be used to visualize stress distribution on the lumbar ...The finite element method of numerical analysis has enabled researchers to solve many ...the ...
24
Development of a 3D finite element model of lens microcirculation
... Our model has calculated a hydrostatic pressure gradient [Figure 6], the existence of which has recently been confirmed experimentally ...that structural components of the lens can influence the magnitude ...
27
Development of a Finite Element Model of the Human Cervical Spine
... Based on the type of FE analysis in cervical spine biomechanics, whether static or dynamic, the necessity of considering the full cervical or multi-segment models has been defined by researchers (49). In dynamic ...
7
Lithium-Oxygen Batteries - A Comprehensive Finite Element Model.
... growth model. A large part of the model developed by Monroe et ...dendrite model that made several critical assumptions such as neglecting mechanical and inertial forces, incorporating surface forces ...
137
Finite element model of a cricket ball impacting a bat
... arrangement (Walker, 1991) was used to measure the moment of inertia (MOI) of each bat. The structural properties of the bats - when suspended from a long string - were measured by means of modal analysis. The ...
7
Structural Damage Detection by Using Finite Element Method as Function of Length
... The experimental investigation was conducted using tensile cyclic tests for different laminates studied. The applied load ratio is 10% of maximum load failure. The loading rate is the ratio of the load relative to the ...
14
Computational Geometric Modeling and Finite Element Structural Analysis of Automobile Camshaft
... The properties of each element are evaluated separately, so an obvious advantage is that we can incorporate different material properties for each element. Thus almost any degree of non-homogeneity can be ...
6
Modelling and Structural Analysis of Leaf Spring using Finite Element Method
... 4. FINITE ELEMENT ANALYSIS OF A LEAF SPRING Engineering analysis can be broadly divided into two categories: classical methods and numerical ...the finite element method is one of several ...
7
Structural Design of Wire Rope Hoist and Finite Element Analysis of Drum
... The motor, drum, drum shaft, rope arrangement mechanism and drive mechanism of the hoist were designed in this paper. The 3d models of the hoist mechanisms were carried out according to the calculation results. And the ...
8
A study on structural health of bicycle frame using Finite Element Analysis
... The innovation in the design of bicycle frame is still going on, the reason behind this is that the manufacturers and construction designers have innovative ideas related to minimize aerodynamic drag, to improve comfort, ...
6
Finite element model of a tennis ball impact with a racket
... (1997a) model, in which the racket is assumed to be rigid, to predict the rebound velocity of both balls when simulating a ...the model using the COR from the head-clamped racket ...FE model could be ...
291
Fuzzy Finite Element based Solution of Uncertain Static Problems of Structural Mechanics
... finite element formulation of equilibrium and steady state problems lead to a set of simultaneous algebraic linear ...in structural mechanics ...find finite element solution of a stepped ...
6
Identification of Structural Model for Chaotic Systems
... This article is talking about the study constructive method of structural identification systems with chaotic dynamics. It is shown that the reconstructed attractors are a source of information not only ...
12
Finite Element Analysis Based Structural Analysis of Horizontal Tube Sheet Filters
... A tube sheet is sheet, a plate, or bulkhead which is perforated with a pattern of holes designed to accept pipes or tubes. These sheets are used to support and isolate to tubes in heat exchangers, filter and boilers ...
8
Calibration of a Structural Finite Element Model for a Representative Inflatable Space Structure Utilizing Probabilistic Methods and Surrogate Models
... A structural finite element model representing a novel inflatable airlock concept has been calibrated using full‐scale test ...the model with test data using a process that included ...
34
Finite element modelling of structural clay brick masonry subjected to axial compression
... the Finite Element Method (FEM) prediction of the masonry behaviour, micro modeling for small masonry prisms using link elements was proposed by Pande et ...in structural masonry was analysed using a ...
12
Finite-Element Model for Pretensioned Prestressed Concrete Girders
... case of bond-slip, since the build up of force due to flexure starts from the initial transfer force. Figure (11) shows the curvature distribution. The curvature localization in the region near midspan is successfully ...
36