tensile in-plane stresses
Field of Stresses in an Isotropic Plane with Circular Inclusion under Tensile Stress
... а plane with а hard inclusion under loading is derived in the present ...The plane-stress state is taken into ...elastic plane with an abso- lutely rigid circular inclusion is presented in ...elastic ...
7
PubMedCentral-PMC5435125.pdf
... uniaxial tensile testing with a focus on the ...uniaxial tensile tests in radial, circumferential and longitudinal directions were ...shear stresses and amounts of shear in the longitudinal than in ...
23
Spallation behaviour of a Zr-bulk metallic glass
... hydro-tensile stresses subjecting to a peak tensile stress along the sample’s ...spallation plane, the resultant microdamage should be microvoids, which would result in nucleation, growth and ...
6
Limit Load Solution for an Edge Cracked Plate under Combined Independent Bi-Axial Membrane and Bending
... The results for the edge cracked plate shown in Figure 3 to Figure 5 show that, in general, Equation (13) provides good estimates for the limit load, for any combination of tensile and bending loads, and for all ...
10
Identification of Out-of-Plane Material Characteristics through Sheet-Metal Blanking
... uniaxial tensile testing are implemented in the out- of-plane blanking experiments to determine shear yield and ultimate stresses and material damage accumulation up to fracture ...
10
Characteristics of High Temperature Tensile Properties and Residual Stresses in Weldments of High Strength Steels
... temperature tensile properties of high strength steels, POSTEN60 and POSTEN80, whose tensile strengths were 600 and 800 MPa respectively, were investigated through the elevated temperature tensile ...
7
IMPROVED INTRINSIC STRESS MODELS FOR THIN FILMS BASED ON SURFACE STRESS
... residual stresses is necessary to fabricate low stress thin films (Tello and Bower, 2008; Pei at ...2019). Stresses in thin films may originate from thermal, intrinsic or extrinsic sources or a combination ...
8
DETERMINATION OF RESIDUAL STRESS DISTRIBUTION IN HIGH STRENGTH ALUMINUM ALLOY AFTER EDM
... residual stresses, which are easy to measure, existing between grains and could be represented by ...micro-residual stresses, which are not easy to determine, usually found around the flaws and ...These ...
7
Evaluation of Structural Stability of an Existing Gravity Dam by Finite Element Method by Applying Pseudodynamic Approach
... The important results obtained from finite element analysis are presented in the form of contours over dam section. A comparison of maximum values of stresses and displacements for static load combinations A, B, ...
6
Thermo mechanically loaded glass fibre reinforced polymer single bolt single lap joints
... The procedure for the ambient temperature joint tests was rapid and straightforward once each joint had been centred and checked for verticality between the grips of the test machine. The tensile load was applied ...
39
Stress Analysis by Finite Element Method of Weir Block having Large Size Multiple Openings- A Case Study
... maximum tensile stress developed in weir block has been observed to remain within allowable tensile strength of concrete, but due to spread of tensile stress on large area, it has become necessary to ...
8
The tensile fracture of mild steel
... described by the maximum tensile stress, hydrostatic tens ion, ratio between two principal stresses, maximum tensile strain, and ratio between two principal strains, all measured at the [r] ...
142
Mode Stresses for the Interaction between Straight and Curved Cracks Problem in Plane Elasticity
... In this paper, the complex variable function method is used to obtain the hypersingular integral equations for the interaction between straight and curved cracks problem in plane elasticity. The curved length ...
10
Experimental Investigation of the Tensile strength and Compressive strength of Fly Ash Core Sandwiched Composite Material
... Abstract: - In this paper, commercially available Fly Ash and Epoxy is used for the core material, woven glass fabric as reinforcing skin material, epoxy as matrix/adhesive materials used in this study for the ...
10
Temperature increase of Zircaloy-4 cladding tubes due to plastic heat dissipation during tensile tests at s 1 strain rates
... displacement a macroscopic strain value. During a PST test at 25 °C, it was shown by Le Saux [10] that a centered area of 1 mm in circumferential direction and 2 mm in axial direction reaches plane strain ...
14
Design of Pressure Vessel Pads and Attachments To Minimize Global Stress Concentrations
... shell stresses due to internal pressure is similar to the problem in plane stress of determining the geometry of an elastic inclusion that produces minimum stress concentration in a biaxial stress ...vessel ...
8
TheEuropeanUnion EDICTOFGOVERNMENT±
... i) The minimum reinforcement steel area should be provided in regions where tensile stresses occur in the concrete under the characteristic combination of actions. In this[r] ...
97
Molecular Dynamics Simulation on Anelasticity under Tensile and Shearing Stresses in Single Component Amorphous Metal
... under tensile and shearing stresses were analyzed by the molecular dynamics method and were compared with the earlier experimental results where an anelastic behavior was not shown in tensile stress ...
5
Safety assessment of critical infrastructures for aircraft crash
... principal stresses, vertical SYY stresses and equivalent plastic strain at two moments – the first one corresponds to maximum value of the time load function ...
9
Optimum Geometry for Pressure Vessel Attachments
... The problem of determining the attachment shape that produces minimum shell stresses due to internal pressure is similar to the problem in plane stress of determining the geometry of an[r] ...
11