Ultra low carbon steel
Effect of Strain on Microstructural Evolution under Warm Deformation in an Ultra Low Carbon Steel
... The microstructural evolution was investigated according to the equivalent strain in uniaxial compression using an ultra-low carbon steel. The equivalent strain was quantitatively calculated ...
6
Precipitation of Copper Sulfide in Ultra Low Carbon Steel Containing Residual Level of Copper
... an ultra low carbon ...This steel is a boron-added steel with ...sheet steel was used in this study. The sample was commercial steel sheet from a blast furnace-LD ...
10
Dry Sliding Wear Properties of Sub Microcrystalline Ultra Low Carbon Steel Produced by High Pressure Torsion Straining
... using ultra-low carbon steel (11C, <30Si, <30Mn, <20P, <3S, <2B, 8N, 14O, 300Al, <20Ti, <30Cr, <30Cu, in mass ppm), which was the same material as that used in the ...
5
Effect of Morphology of Copper Precipitation Particles on Hydrogen Embrittlement Behavior in Cu Added Ultra Low Carbon Steel
... while the ε-copper in the later region. In each relationship, the normalized SP energy is inclined to decrease with increasing hydrogen content, however, the decrease seems to be more prominent in the copper ...
6
Maximize Tensile Strength in Aluminium Alloy Joints Using Parametric Optimisation of Linear Friction Welding
... and ultra-low carbon steel, in which the mixing pin was dove into steel ...the steel surface ...and ultra-low carbon steel was effectively delivered ...
9
Influence of Carbon Content on Solidifying Shell Growth of Carbon Steels at the Initial Stage of Solidification
... an ultra-low carbon steel ...hypo-peritectic carbon steel (0.116 mass% C), while for a low carbon steel ...hyper-peritectic carbon steel (0.304 ...
9
Corrosion, Microstructure and Mechanical Performance of Ultra Low C/Cr Stabilized Steel
... rolled ultra-low carbon steel sheet with ...Cr/stabilized steel) was evaluated in different concentration NaCl solution (neutral pH) to assess their corrosion ...the steel by ...
9
Development of Ultra-Carbon Steel Prepared by Mechanical Alloying and Subsequent Hot Pressing
... Figure 8 shows the SEM images of the cross section of the fracture surface of the Fe-0.4C compacts HPed at various temperatures after tensile test. In the case of HP at 610ºC, the fracture surface consists of many small ...
5
Understanding dual precipitation strengthening in ultra-high strength low carbon steel containing nano-sized copper precipitates and carbides
... Low carbon ferritic steel alloyed with Ti, Mo and Cu was hot rolled and interrupt cooled to produce nano‑sized precipitates of copper and (Ti,Mo)C ...The steel had a tensile strength of 840 ...
8
Effect of Neutron Irradiation on Mechanical Behavior of Ultra-Fine Grained Low Carbon Steel -- Application to Next Generation Fission Reactors.
... Energy is essential to economic development and improved quality of life. Nuclear energy is considered to be a relatively sustainable energy source that can provide clean (no carbon dioxide emissions) and ...
139
Grain Boundary Character and Superplasticity of Fine Grained Ultra High Carbon Steel
... studied in an ultra-high carbon steel (Fe–1.4Cr–1.0C). After heavy warm rolling of pearlite, an ( α + θ ) microduplex structure with equi-axed α grains of 0.4 µm in diameter and spheroidized θ ...
8
Morphology and Crystallography of Sub Blocks in Ultra Low Carbon Lath Martensite Steel
... The steel used in this study has the following chemi- cal composition: Fe-0.0049 mass%C-3.14 mass%Mn-0.011 mass%Nb-0.021 mass%Ti-0.0025 mass%B. In order to ob- tain the lath martensite structure, specimens with a ...
5
Microstructures and Mechanical Properties of Ultra Low Carbon Interstitial Free Steel Severely Deformed by a Multi Stack Accumulative Roll Bonding Process
... An ultra low carbon interstitial free (IF) steel was severely deformed by the six-layer stack accumulative roll-bonding (ARB) process for improvement of the mechanical ...
5
Microstructures and Mechanical Properties of Ultra Low Carbon IF Steel Processed by Accumulative Roll Bonding Process
... Changes in TEM microstructure observed at ND plane of the specimen ARBed by 5 cycles with annealing tempera- ture are shown in Fig. 4. As shown in Fig. 4(a), the ultra- fine grains with clear grain boundaries were ...
6
Inhibiting Corrosion of Crown Corks of Fanta using an Eco Friendly Inhibitor
... The Figures presented in 1 to 6 again, show that immersion time has a significant effect on the corrosion of mild steel. In the presence of DG, it was observed that inhibition efficiency reduced with an increase ...
6
Ductile Behaviour Characterization of Low Carbon Steel: a CDM Approach
... Low carbon steels, such as IFHS and C-Mn-440, show a good combination of strength and formability. These attributes aid in manufacturing shape-critical structures of automobiles. The current study is ...
8
Electrochemical Behaviour of Low Carbon Steel in Aqueous Solutions
... the low carbon content steels such as 070- M20, A106 and API5L showed higher weight reductions from ...high carbon content (080-M40 and 070-M55) which gave values of ...and carbon dioxide gas, ...
7
Carburizing Effect On Impact Toughness Of Low Carbon Steel
... less carbon than other steels and are inherently easier to cold-form due to their soft and ductile ...concern, low-carbon steels are good choices because they are easy to handle such as to draw, ...
24
Numerical Simulation of Multilayer Hardfacing on Low Carbon Steel
... of low carbon steel plate using low heat input tubular chromium-carbide based electrodes is ...of low carbon steel plate is performed using ANSYS ...mild steel ...
11
Effect of Ceramic Powder Coatings on Low Carbon Steel
... of steel was grinded to a mirror like surface using the polishing machine to provide uniform or levelled surface for deposition of ceramic ...the steel sample was deter- mined by mass ...the low ...
11