uniaxial tensile tests
Re-examination of the mechanical anisotropy of porcine thoracic aorta by uniaxial tensile tests
... mechanical tests. In the tests, the engineering stress σ and strain ε were calculated by σ = F/A and ε = Δl/l, respectively, where F is the tension force, A is the initial cross-sectional area obtained by ...
14
An Investigation to Nonlinear Elastic Behavior of Pericardium Using Uniaxial Tensile Test
... biaxial tensile tests [8]. Lee and Bough- ner conducted uniaxial tensile tests on the human and canine pericardium tissue to compare the viscoelastic response, showing that the human ...
12
Air Permeability of Elastomeric Fabrics as a Function of Uniaxial Tensile Strain
... Realff [24] explained regarding the various changes in the yarn geometry occurring during fabric deformation in uniaxial tensile loading. For the experimental purpose she constructed various plain weave ...
144
Deformation Mechanisms in Nanoscale Single Crystalline Electroplated Copper Pillars
... and uniaxial compression tests (pillars) as well loading conditions: strain rates and experimental constraints are different; (5) and finally different stress states: thin films have a 2-D stress state ...
239
Retardation of Softening of Ultrafine Grained Copper during Low Temperature Annealing under Uniaxial Tensile Stress
... under uniaxial tensile stress and that without ...the uniaxial stress of 100 MPa in the case of LTA under uniaxial tensile ...the uniaxial tensile stress of 100 MPa was ...
5
High strain rate and quasi-static tensile behaviour of Ti-6Al-4V after cyclic damage
... [12], so standard fatigue specimens are used for cyclic loading and the smaller Hopkinson specimen is extracted from it after damage has been applied (see figures 2 and 3). In order to obtain fatigue damaged specimens, ...
6
Petrography of Jutana Dolomite: Implications for Geotechnical Utility
... collected. Tests were performed on the cores extracted from collected block ...diameter. Uniaxial tensile strength is used to verify tensile strength of rock samples or its resistance against ...
5
Uniaxial Loading Deformation Tests in Studying Serration Flow of Alloy C460
... The tensile test specimens were solution heat treated as received for three different aging times of 6, 18, and 24 hours at a temperature of ...160°C. Tensile tests were carried out with a crosshead ...
5
Forming Limit Prediction of High Tensile Strength Steel using FEA Simulation
... FLD comparison between experimental results and analytical results is shown in Fig. 8. The ductile fracture criterion was applied in the analytical FLD at the uniaxial tensile side (plots of FEM-1). The ...
5
Effect of Construction on Strain distribution in Woven Fabrics under Uniaxial Tensile Deformation
... the tensile behavior of woven fabrics by proposing a generalized model which also considered the interlacement distribution pattern of the ...of tensile properties of woven ...during tensile loading ...
11
Uniaxial Tensile Stress-Strain Relationships of RC Elements Strengthened with FRP Sheets
... mathematical expressions for concrete and steel in uniaxial tension were proposed. The effects of the FRP reinforcement ratio, steel reinforcement ratio, and the wrapping scheme were studied. Although most ...
35
Properties of Moldings Prepared from LDPE-Pumpkin Seed Hulls Blend
... static tensile testing and hardness measurement, of injection molds produced at constant process- ing ...between tensile modulus, maximum tensile stress, tensile stress at yield, maximum ...
8
Characterization of Some Selected Limestone Deposits in ogun State, Nigeria for Prediction of Penetration Rate of Drilling
... 4).The uniaxial compressive strength of the samples was estimated from the chart named after Deere and Miller, ...The uniaxial compressive strength of samples from location A varies from ...the ...
6
Mechanical properties of magnetostrictive iron- gallium alloys
... tested. Two were cut with the [110] direction parallel to the tensile axis. The major faces of these specimens were (001) planes, and the minor faces were (1 1 0) planes. The other two specimens were cut with the ...
12
Estimating the Mechanical Properties of Travertine Building Stones Due to Salt Crystallization Using Multivariate Regression Analysis
... To carry out the research, a number of travertine samples were subjected to salt crystallization test in a sodium sulfate solution under the same conditions. The test up to 50 cycles was carried out and, after every 5 ...
11
Estimation of the Ampere Consumption of Dimension Stone Sawing Machine Using of Artificial Neural Networks
... types of movement, i.e. manual, semi-automatic and fully-automatic. The feed rate is measured by an electronic counter. The intensity of electric current consumption (Ampere) in different machinery conditions is measured ...
9
Influence of Uniaxial Tensile Stress on the Mechanical and Piezoelectric Properties of Short period Ferroelectric Superlattice
... ideal tensile strength is ...of uniaxial tensile stress becomes soft along the nonpolar ...applied uniaxial tensile stress can signifi- cantly enhance the piezoelectricity for the ...
5
Compressive behaviour of wheat from confined uniaxial compression tests
... characteristics of granular wheat stored in silos. The confined uniaxial compression tests of wheat were performed to investi- gate the compression behaviour of granular wheat. The effects of different ...
8
Online Full Text
... The tensile properties of cortical bone in longitudinal and transverse directions were determined from uniaxial tensile test conducted on Zwick 7250 Universal Testing Machine (25 T ...the ...
6
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
... Two models of shift factors commonly used for binders and asphalt mixtures were used in the study – WLF and Arrhenius [52]. The reference temperature for which the master curves and shift factors were determined was ...
20