USB serial are used to connect the Arduino

Top PDF USB serial are used to connect the Arduino:

Arduino Nano RP2040 Connect

Arduino Nano RP2040 Connect

3.4 WiFi/Bluetooth connectivity Wifi and Bluetooth connectivity is provided by the Nina W102 (U2) module. The RP2040 only has 4 analog pins, and the Nina is used to extend that to the full eight as is standard in the Arduino Nano form factor with another 4 12-bit analog inputs (A4-A7). Additionally, the common anode RGB LED is also controlled by the Nina W-102 module such that the LED is off when the digital state is HIGH and on when the digital state is LOW. The internal PCB antenna in the module eliminates the need for an external antenna. The Nina W102 module also includes a dual core Xtensa LX6 CPU that can also be programmed independantly of the RP2040 through the pads under the board using SWD.
Show more

19 Read more

Arduino project. Arduino board. Serial transmission

Arduino project. Arduino board. Serial transmission

Read and fill in the gaps Overview The Arduino Uno is a microcontroller board .....on the ATmega328 . It has 14 ............... input/output pins (of which 6 can be used as PWM.........), 6 analog inputs, a 16 MHz ceramic resonator, a USB............., a power jack, and a reset button. It contains everything needed to support the microcontroller; simply ........it to a computer with a USB cable or power it with a AC-to- DC .......... or battery to get started.

8 Read more

USB to serial chip CH340

USB to serial chip CH340

MODEM liaison signal pins contain: CTS#, DSR#, RI#, DCD# and RTS#. All these MODEM liaison signal are controlled and function defined by computer applications. Assistant pins contain: IR#, R232, CK0, ACT# and TNOW. When IR# is low-level, infrared serial interface mode is enabled. R232 pin is used to control assistant RS232 function. If R232 pin is driven high, the RXD pin input will be reversed automatically. ACT# pin is USB device configuration complete status output (such as USB infrared adapter ready). TNOW pin indicates CH340 is transmitting data from UART when it is high-level and becomes low when transmit over. In RS485 and other half-duplex mode, TNOW could be used to indicate UART transmit-receive status. IR# and R232 are detected only once when chip powered on and reset.
Show more

9 Read more

Universal Serial Bus (USB)

Universal Serial Bus (USB)

1 Introduction Usages.are part of the HID Report descriptor and supply an application developer with information about what a control is actually measuring or reporting. In addition, a Usage tag can be used to indicate the vendor’s suggested use for a specific control or a group of controls. While most of the items within a Report descriptor describe the format of the data – for example, thee 8-bit fields—the Usage tags define what should be done with the data – for example, x, y, and z input. This feature allows a vendor to ensure that the user sees consistent function assignments to controls across applications. It is also the key feature within HID Report descriptors that allows system or application software to know the meaning of data items, or collections of data items, so the data items can be correctly interpreted or routed to the system or application software that consumes them.
Show more

68 Read more

Universal Serial Bus (USB)

Universal Serial Bus (USB)

4. Conventions 4.1 Actuators An Actuator is a mechanism that can exert a force against an object. Typically the force applied by the actuator can defined in some combination of 6 dimensions; X, Y, Z, Rx, Ry and Rz. By definition in the HID specification these dimensions are defined in a coordinate system that is referenced to the direction that the user is facing. For simplicity the usages X, Y, Z, Rx, Ry and Rz from the Generic Desktop page are used by PID class devices to define a NORMALIZED force values. i.e. if the Logical Minimum and Logical Maximum values for an axis are defined to be -100 and +100 respectively, then -100 represents maximum force in the negative direction, 0 no force, and +100 maximum force in the positive direction. If a device requires the assertion of precise absolute force then the Vectors Vx, Vy, and Vz can be used from the Generic Desktop usage table with Units declaring the actual range of applied force. Linear absolute forces result from setting the Units associated with the vector usages to SI Linear or English Linear.
Show more

52 Read more

Arduino Lesson 5. The Serial Monitor

Arduino Lesson 5. The Serial Monitor

The line beginning with 'while' ensures that there is something at the other end of the USB connection for the Arduino to talk to before it starts sending messages. Otherwise, the message might be sent, but not displayed. This line is actually only necessary if you are using an Arduino Leonardo, because the Arduino Uno automatically resets the Arduino board when you open the Serial Monitor, whereas this does not happen with the Leonardo.

11 Read more

VADDIO QUICK-CONNECT USB INTERFACE

VADDIO QUICK-CONNECT USB INTERFACE

Vaddio Technical Support : Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at support@vaddio.com or online at vaddio.com. Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products returned for credit are subject to a restocking charge without exception.
Show more

36 Read more

USB to Serial Quick Installation Guide

USB to Serial Quick Installation Guide

USB to Serial is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names used in this publication are for identification only and may be trademarks of their respective owners.

12 Read more

Micro USB to RS232 Serial Adapter Cable for Android with USB Charging

Micro USB to RS232 Serial Adapter Cable for Android with USB Charging

FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

8 Read more

USB Serial Adapter ICUSB232SM3. Instruction Manual. 1-Port 3ft USB to RS232 DB9 Serial Adapter Cable

USB Serial Adapter ICUSB232SM3. Instruction Manual. 1-Port 3ft USB to RS232 DB9 Serial Adapter Cable

FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

8 Read more

USB Serial Device Firmware Upgrade (DFU)

USB Serial Device Firmware Upgrade (DFU)

usbserialdevice.c This is the main application file. Originally, there were two tasks: one for transmitting data and one for receiving data. In this example, a third task is added (dfuFxn) which will initiate the switch to device firmware upgrade mode. The DFU task will wait until the other two tasks have completed. An event object is used for synchronizing the tasks. The original tasks are modified to check the DFU request flag, and to terminate when this flag is set.

46 Read more

USB to RS232 Serial DB9 Adapter Cable

USB to RS232 Serial DB9 Adapter Cable

FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

8 Read more

USB-Serial Conversion Cable User's Manual

USB-Serial Conversion Cable User's Manual

The actual driver installation method depends on the OS being used. Windows 2000 is used in the examples in this section. Note The USB-Serial Conversion Cables are compatible with Windows XP. When you install the Conversion Cable's driver, a warning message will appear indicating that the driver software has not passed Windows Logo testing, but click Continue Anyway to proceed with the installation. We have thoroughly tested the driver on Windows XP and verified the it operates properly.

43 Read more

How To Connect A Port Replicator With An Ethernet To A Usb Port From A Usb Device

How To Connect A Port Replicator With An Ethernet To A Usb Port From A Usb Device

The system locates the correct software driver. 2 Click Next to install the driver. 3 When the installation complete message appears, click Finish. Congratulations! You have installed the Targus USB Mobile Port Replicator with Ethernet. The new ports available to you are: two USB, two PS/2, one serial, one parallel, and one RJ-45 Ethernet port. They are numbered sequentially following the existing ports in your computer.

16 Read more

Designing a. Universal Serial Bus (USB) Device. Using the Cypress CY7C A USB Thermometer

Designing a. Universal Serial Bus (USB) Device. Using the Cypress CY7C A USB Thermometer

Control Transfers handle most stages of the enumeration process: Get Device Descriptor, Set Address, Get Configuration Descriptor, and Set Configuration. Since Control Transfers are used for fundamental control of the device, they are very critical. Cypress provides assembly language routines to handle the common control transfers the device will receive. The designer should be familiar with them in order to be able to add the device specific requirements of their design. These routines are located in USB.ASM on the Cypress USB CD-ROM.

35 Read more

USB-to-Serial RS-232 Hub USB-to-Serial RS-422/485 Hub USER MANUAL UC2322 / UC2324 / UC4852 / UC4854

USB-to-Serial RS-232 Hub USB-to-Serial RS-422/485 Hub USER MANUAL UC2322 / UC2324 / UC4852 / UC4854

FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

18 Read more

Microsoft Windows Built-In Serial and USB UPS Support

Microsoft Windows Built-In Serial and USB UPS Support

How to Configure Windows 2003, XP and 2000 to Work with a Serial UPS The UPS Tab allows you to select a UPS model. Windows 2003/XP/2000 support both serial basic-signaling and advanced-signaling models. Generally, if you connect the communications cable that came with the UPS and select the manufacturer, family, and COM port, communications will be established. UPS signaling to the control panel applet will depend on the type of UPS used. Defaults in the UPS Selection screen assume you are using the cable that came in the box with the UPS (note: some UPSs actually support both advanced and basic signaling).
Show more

9 Read more

Professional USB to Serial Adapter Hub with COM Retention

Professional USB to Serial Adapter Hub with COM Retention

Instruction Manual FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Show more

18 Read more

USB Serial Adapter. User Manual. Connect your Serial Device through USB. F5U103vea

USB Serial Adapter. User Manual. Connect your Serial Device through USB. F5U103vea

le pilote de l’adaptateur dès que vous branchez l’adaptateur (sur lequel le périphérique série est branché) au port USB de votre ordinateur ou hub. Cliquez sur « Suivant » pour continuer. Sélectionnez « Rechercher le meilleur pilote pour votre périphérique (Recommandé) » puis cliquez sur le

40 Read more

EIBWeiche Serial/USB

EIBWeiche Serial/USB

1. You need a PC with NT/2000/XP. Connect the EIBWeiche to the PC. If you have an USB- EIBWeiche, the Win2000/XP driver is automatically installed from the b+b-EIBTools-CD, if you connect the EIBWeiche the first time. 2. Test the communication between PC and EIBWeiche, while starting the tool „OpenEIBDemo“ di- rect from CD (it is located in the folder „SDKs and more\OpenEib\OpenEib SDK\BIN“). With this tool you can establish a connection to the EIBWeiche and also directly configure the physical EIB- address.

15 Read more

Show all 10000 documents...