• No results found

[PDF] Top 20 Analysis & Design of Reinforced Concrete Building (G+4) using ETABS

Has 10000 "Analysis & Design of Reinforced Concrete Building (G+4) using ETABS" found on our website. Below are the top 20 most common "Analysis & Design of Reinforced Concrete Building (G+4) using ETABS".

Analysis & Design of Reinforced Concrete Building (G+4) using ETABS

Analysis & Design of Reinforced Concrete Building (G+4) using ETABS

... water tank has been placed and their load has been considered on the structure. As the location of the structure is in Bangalore, wind load has been considered 33m/s as per IS 875 part 3 annex A, Structure Class B and ... See full document

8

An Investigational Study of Commercial Building  Case Study

An Investigational Study of Commercial Building Case Study

... commercial building(Basement+G+3) using Etabs which is compressive analysis, design and detailing software for superstructure (Beams, Columns) of any building, ... See full document

5

Analysis and Design of Commercial Building using ETABS

Analysis and Design of Commercial Building using ETABS

... residential building and designed the various components like beam, slab, column and ...the reinforced concrete building depends upon the initial architectural and structural configuration of ... See full document

6

SEISMIC ANALYSIS OF MULTISTORIED BUILDING WITH AND WITHOUT VERTICAL MASS IRREGULARITY

SEISMIC ANALYSIS OF MULTISTORIED BUILDING WITH AND WITHOUT VERTICAL MASS IRREGULARITY

... the design of structures to resist the gravity loads, usually most structures tend to be adequate against vertical ...shaking. ETABS is an integrated analysis, design and drafting of buildings ... See full document

6

Seismic Retrofitting of Reinforced Concrete Frame Building with Soft Storey

Seismic Retrofitting of Reinforced Concrete Frame Building with Soft Storey

... retrofitted G+4 open ground storey reinforced concrete frame building with Bracing and Brick wall model is done using STAAD Pro for Seismic coefficient method and Manual ... See full document

6

ANALYSIS AND DESIGN OF COMMERCIAL BUILDING USING ETABS

ANALYSIS AND DESIGN OF COMMERCIAL BUILDING USING ETABS

... and Design of Commercial building with bracings using ETABS” is an attempt to analyse and design a commercial building using ...A G+9 storey building is ... See full document

6

Seismic Analysis and Design of G+18 Floors Multistoried Building using ETABS 2013

Seismic Analysis and Design of G+18 Floors Multistoried Building using ETABS 2013

... of design is adopted in the design of all the component of the ...of concrete for the structure with T or 40 steel for ...the design IS456-2000, SP-16 and national building code have ... See full document

8

Comparative Analysis and Design of Multi Story Composite and Conventional Reinforced Concrete Frame Structure (G+21) by using ETABS

Comparative Analysis and Design of Multi Story Composite and Conventional Reinforced Concrete Frame Structure (G+21) by using ETABS

... and concrete and it has applied in many Multi-Story commercial buildings and factories as well as in bridges ...example concrete cores encircled by steel tubes as well as in composite structures, where ... See full document

8

Comparative Study on Analysis and Design of Regular Configuration of Building by Staad Pro and Etabs

Comparative Study on Analysis and Design of Regular Configuration of Building by Staad Pro and Etabs

... and ETABS, a computer programs that has been developed for the static and seismic stability evaluations of different civil engineering structures and concrete gravity ...involves analysis and ... See full document

5

COMPARATIVE STUDY ON DESIGN RESULTS OF RCC FRAME STRUCTURE USING STAAD PRO AND ETABS FOR REGULAR AND IRREGULAR PLAN

COMPARATIVE STUDY ON DESIGN RESULTS OF RCC FRAME STRUCTURE USING STAAD PRO AND ETABS FOR REGULAR AND IRREGULAR PLAN

... the analysis and design of building structures which might consists of structural members like beams, columns, slabs, shear walls ...With ETABS you can easily apply various construction ... See full document

9

A Detailed Study on the Design and Seismic Analysis of G+18 Floors Multistoried Building by Using Etabs 2013

A Detailed Study on the Design and Seismic Analysis of G+18 Floors Multistoried Building by Using Etabs 2013

... multistoried building, which can serve many people in available limited ...multistoried building with all ...element analysis software, which divides the element into very small slices and models the ... See full document

7

Analysis of G+20 RC Tall Building in Different Zones using ETABS

Analysis of G+20 RC Tall Building in Different Zones using ETABS

... C building subjected to earth quake load by adopting Linear or equivalent static ...to reinforced concrete (RC) multi- storied commercial building with FOUR different zones II, III, IV & ... See full document

9

Analysis and Design of Multistory Building with Grid Slab Using ETABS

Analysis and Design of Multistory Building with Grid Slab Using ETABS

... Dynamic Analysis of Special Moment Resisting Frame Building with Flat Slab and Grid ...of concrete building construction uses a flat concrete slab (without beams) as the floor ... See full document

8

A Comparative Study on High Rise Building for Various Geometrical Shapes Subjected to Wind Load of RCC & Composite Structure using ETABS

A Comparative Study on High Rise Building for Various Geometrical Shapes Subjected to Wind Load of RCC & Composite Structure using ETABS

... – concrete composite structure as well as conventional RCC beam column structure using ETABS ...conventional reinforced concrete ... See full document

6

A Study on the Analysis and Design of Commercial Building (G+9) Using Response Spectrum Method in ETABS

A Study on the Analysis and Design of Commercial Building (G+9) Using Response Spectrum Method in ETABS

... engineering design process. Creation of models in ETABS is easier - intuitive drawing commands allow for the rapid generation of floor and elevation ...into ETABS models or used as templates onto ... See full document

7

COMPARATIVE STUDY OF SEISMIC RESPONSE OF REGULAR AND IRREGULAR BUILDING WITH SHEAR WALL

COMPARATIVE STUDY OF SEISMIC RESPONSE OF REGULAR AND IRREGULAR BUILDING WITH SHEAR WALL

... rise reinforced concrete building in seismic zone 4 is done by ETABS v ...software using response spectrum analysis which is analyzed by changing various location of shear ... See full document

13

Optimization of steel truss configuration for structural efficiency using STAAD.Pro and ETABS

Optimization of steel truss configuration for structural efficiency using STAAD.Pro and ETABS

... models using ETABS Integrated Building Design Software and ...structural analysis and design Program. ETABS has been developed specifically for multi-story commercial and ... See full document

11

Analysis of a Multistoried Commercial Cum Residential Building using ETABS

Analysis of a Multistoried Commercial Cum Residential Building using ETABS

... Residential Building using ETABS” deals with the analysis and design of a multi-storied commercial cum residential building(B+G+3) using the software ETABS ... See full document

5

SEISMIC RESPONSE OF REINFORCED CONCRETE MONOLITHIC BUILDING PROVIDED WITH BASE ISOLATION

SEISMIC RESPONSE OF REINFORCED CONCRETE MONOLITHIC BUILDING PROVIDED WITH BASE ISOLATION

... a G+7 storey reinforced concrete monolithic residential building subjected to seismic forces using response spectrum method in ETABS Software with fixed base and isolated ...The ... See full document

16

Analysis and Design of Multistorey Building (G+3) by using ETABS Software

Analysis and Design of Multistorey Building (G+3) by using ETABS Software

... of building systems. The main purpose of this software is to design multistoried building in a systematic ...effective design and construction of an earthquake resistant structure have great ... See full document

7

Show all 10000 documents...