[PDF] Top 20 On the Anisotropic Mechanical Properties of Selective Laser Melted Stainless Steel
Has 10000 "On the Anisotropic Mechanical Properties of Selective Laser Melted Stainless Steel" found on our website. Below are the top 20 most common "On the Anisotropic Mechanical Properties of Selective Laser Melted Stainless Steel".
On the Anisotropic Mechanical Properties of Selective Laser Melted Stainless Steel
... utilized laser power and the ability to control the thermal environment, ...good properties in the as-built state a post-heat treatment is in most cases not ... See full document
18
Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V
... on mechanical properties was studied by Andrei et ...and mechanical properties in SLM Ti6Al4V ...and mechanical properties of SLM Ti6Al4V ...the mechanical ... See full document
11
Effect of Process Parameter Modification and Hot Isostatic Pressing on the Mechanical Properties of Selectively Laser-Melted 316L Steel
... Specimen selection was based on the preliminary test results, in which the S_01 specimen group was characterized by the best tensile properties and the S_17 group had the worst. The primary purpose of HIP ... See full document
24
Microstructure and Properties of Selective Laser Melting Forming Precipitation Hardening Stainless Steel
... and mechanical properties of the molded part are significantly ...The mechanical properties of SLM molded parts are higher than the casting level, which is close to or even slightly higher ... See full document
5
Effect of the Particle Size of 316L Stainless Steel on the Corrosion Characteristics of the Steel Fabricated by Selective Laser Melting
... [3], selective laser sintering (SLS) [4], selective laser melting (SLM) [5], electron beam melting (EBM) [6] and binder jet 3D printing (BJ3DP) ...excellent mechanical ... See full document
16
Nano hardness and microstructure of selective laser melted AlSi10Mg scan tracks
... the laser beam melts the powder line-by-line forming a consolidated layer from overlapping melt ...as laser power, scan speed, layer thickness, substrate material, and the properties of the powder ... See full document
7
Investigating The Heat Treatment Parameters Of En-31 Using Taguchi Method
... Stainless steels generally contain between 10-20% chromium as the main alloying element and are valued for high corrosion resistance. With over 11% chromium, steel is about 200 times more resistant to ... See full document
11
Multiscale characterisation of the mechanical properties of austenitic stainless steel joints
... So at the macroscale, the sample has shear bands extended over several grains. At the same time at the microscale slip bands form within the grains, localising the strains. These slip bands are constrained within the ... See full document
26
Effect of gold treatment on the mechanical properties of 316L stainless steel
... It is known that applying stress to austenitic stainless steels produces a variety of deformation microstructures, depending on material and testing conditions. Tangled random dislocations, dislocation pile-ups, ... See full document
24
Effect of Welding Consumables on the Mechanical Properties of Micro Alloyed Steel Weldment
... Fig. 2 shows the optical micrograph of the base metal (BM). The micrograph reveals white patches of fine grains of ferrite with dark spots indicating scattered carbide precipitates and small patches of pearlite. The ... See full document
7
Effect of Aging on Mechanical Properties of S465 Stainless Steel
... required dimensions i.e., 10mmx10mmx12mm samples by using CNC Wire cut E.D.M Wire cut machine- After sectioning, all samples are subjected to different heat treatment conditions prior to testing. The heat treatment was ... See full document
8
New approaches to designing parts for digital additive productiona
... determining mechanical properties have been carried out in accordance with ISO 6892-1 at test machine Zwick/Roell Z100 (Germany) with maximum force of 99,640 ... See full document
8
Analysis The Contribution And Effect Of Coolant To Surface Roughness In Cylindrical Grinding
... For the previous student only study about the surface roughness measurement and effect that involved from the surface roughness. The previous study state the coolant is the one of the effect that involved in surface ... See full document
24
Effects of Solution Treatment and Cold Rolling on Microstructure and Mechanical Properties of Stainless Steel for Surgical Implants
... received much attention as material for stents and stent grafts owing to its very good elasticity, high mechanical strength, excellent ductility and good cold workability. It has recently been reported that ... See full document
5
Fatigue properties of dissimilar metal laser welded lap joints
... The fatigue tests carried out were of the tension/tension type with a sinusoidal waveform. The load ratio (minimum load/maximum load) was 0.05 = R. The fatigue test frequency was selected on the basis of the highest ... See full document
372
EFFECT OF INTERMETALLIC PHASES ON CORROSION BEHAVIOR AND MECHANICAL PROPERTIES OF DUPLEX STAINLESS STEEL AND SUPER-DUPLEX STAINLESS STEEL
... Duplex stainless steels (22% Cr) and Super Duplex Stainless Steels (25% Cr) are a family of steels having a combination of excellent corro- sion resistance and mechanical ...ferritic stainless ... See full document
19
Mechanical Properties and Microstructural Development in Irradiated 316 Stainless Steel
... Since the measured yield strength decreases with increasing temperature, the strengthening due to voids increases at higher temperature, and the strengthening due t[r] ... See full document
8
Multiscale characterisation of the mechanical properties of austenitic stainless steel joints
... of stainless steel 316L has been tensile tested for three blocks with the joint at the centre and to understand the stress-strain behaviour and the macro/micro deformation ...highly anisotropic ... See full document
27
Effects of heat treatment on the microstructures and electrochemical behavior of stainless steel
... austenitic stainless steel normalized at 900 ° C for (a) 1 hour and (b) 2 hours (c) 8 hours consisting of equiaxed austenite grains, Spot A = at dark area, Spot B = at grain boundary, ... See full document
29
Mechanical and electrochemical properties of multiple layer diode laser cladding of 316L stainless steel
... the laser processing, detailed microstructural study of the top surface and cross section of the fabricated component was carried out by optical and scanning electron ... See full document
5
Related subjects