[PDF] Top 20 ATALYTIC CRACKING OF PLASTIC (TO OBTAIN HYDROCARBON FUEL)

... Most of the catalyst that are employed for the catalytic polymer cracking is acid micro poroussolids. Severalliquids and gases are obtained, in different proportions, based on catalyst selection. Main factor that ... See full document

... of plastic types. Preliminary tests on the produced WPPO fuel have shown that it is a mixture of various hydrocarbons having a range of carbon chain lengths from C3 to ...WPPO fuel density has its ... See full document

... polymer fuel has been analyzed by its physical properties and chemical ...commercial fuel have been thoroughly ...the hydrocarbon liquid fuel in GC test, the gases and residuum can also be ... See full document

... waste plastic. Statistics show that approximately 10% of the plastic is recycled, 25% is incinerated and the remaining 65% is dumped in ...of plastic in the landfill would definitely cause serious ... See full document

... the cracking reaction of the pyrolysis gas, but when the amount of catalyst was too much, the presence of catalyst could reduce the liquid fraction and increased the gaseous fraction [11], while the purpose of ... See full document

... liquid fuel 85%, light gas 9% and black carbon residue ...that hydrocarbon compound and light gas were present in the range of C3- C28 and present C1-C4, ... See full document

... of fuel are being tackled ...get fuel oil that has the same physical properties as the fuels like petrol, diesel ...component Plastic goes under depolymerisation, pyrolysis, thermal cracking ... See full document

... waste plastic is a propitious method for the conversion of waste into liquid hydrocarbons [5] ...the plastic waste is reduced significantly by around 50% to 90%, the solid, liquid and gaseous fuel ... See full document

... diesel fuel range boiling were hydrogenated over platinum ...thermal cracking temperature of waste polyolefin is 410-430°C, in the case of catalytic Process lower temperature, ...obtained fuel ... See full document

... waste plastic thrown into the ocean causes friction of ocean waves and then broken down by sunlight into small pieces and takes the shape of plastic like ...the plastic soup as their food and can’t ... See full document

... convert plastic waste in to hydrocarbon fuel and separate residue by pyrolysis process along with various parameters such as, temperature, pressure and time for individual and mixed plastic ... See full document

... of plastic wastes has been ...of plastic content and plastic type in the feed and the presence of a Ni/Al2O3 catalyst on the yield and composition of the final ...of plastic wastes. He ... See full document

... probable cracking, the main topic of this research, occurs shortly after casting, while the concrete still is in its plastic phase, Figure ...The cracking occurs when the concrete surface dries and ... See full document

... waste plastic is generated in India 15000 tons per day (as per government survey) ...waste plastic affects the humans, animals, birds’ earth and ...(breakdown) plastic may require around 500 years in ... See full document

... The choice of model “Reactor” + CHEMKIN II is jus- tified by the fact that we model the phase homogeneous combustion that is controlled by chemical kinetics. This justifies the dominance of the phenomenon of chemical ... See full document

... Is diesel and biodiesel the same thing? Biodiesel is the name of clean burning alternative fuel, produced from domestic, renewable resources. Biodiesel contains no petroleum, but it can be blended at any level ... See full document

... PET is abbreviation for Polyethylene Terephthalate from one of polymer groups out of seven. Polyethylene terephthalate (PET) has turned into the greatest bundling material worldwide for water and soft drinks bottles ... See full document

... diameter. Hence the separation of gaseous phase and the liquid phase perfect and no liquid phase is entered into the condenser. The quality of the condensate is improved due to high length to diameter ratio for the ... See full document

... Warm breaking or Pyrolysis, includes the corruption of the polymeric materials by warming without oxygen. The procedure is typically directed at temperatures between 350 °C and 900 °C and results in the development of a ... See full document

... undesirable hydrocarbon fragments and derivatives, often in particulate form, carbon monoxide, and gaseous oxides of nitrogen and/or of sulfur transformable to noxious droplet form (acid ...ideal fuel ... See full document