[PDF] Top 20 DEFINITY Enterprise Communications Server Application Notes for Type Approval

... Part 15: Class A Statement. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea- sonable ... See full document

... Links DEFINITY ECS and adjunct applications. The interface allows adjunct applications to access DEFINITY ECS features and supply routing information to the system. CallVisor ASAI improves ACD agents’ call ... See full document

... an application layer called the Telephony Manager, and a registration ...registration application handles ...any type of audio path of bearer ... See full document

... The TN2313 DS1 port board interfaces a DS1 trunk to the switch backplane via port slots that are standard for DEFINITY products. The TN2313 is compatible with previous DS1 circuit packs, including the TN464F (V19 ... See full document

... an application layer called the Telephony Manager, and a registration ...registration application handles ...any type of audio path of bearer ... See full document

... This type of Third Party Make Call is used by many types of applications such as Office Automation, Messaging, and OCM applications for Preview ...this type of call include all station ...this type ... See full document

... This type of Third Party Make Call is used by many types of applications such as Office Automation, Messaging, and OCM applications for Preview ...this type of call include all station ...this type ... See full document

... change system-parameters customer-options Page 2 of 6 OPTIONAL FEATURES Abbreviated Dialing Enhanced List? y CAS Branch? y Access Security Gateway (ASG)? y CAS Main? y Analog Trunk Incoming Call ID? y Change COR by FAC? ... See full document

... The length of the reset shift dial tone is administrable on a system basis and should have a range of 0-255. It is normally set to 10 seconds. Japanese PBXs can give this tone for up to 1 or 2 minutes before reverting to ... See full document

... Part 15: Class A Statement. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea- sonable ... See full document

... allows DEFINITY ECS to compare specified splits or skills, identify the split or skill that will provide the best service to a call, and deliver the call to that ... See full document

... If you suspect that you are being victimized by toll fraud and you need technical support or assistance, call the Lucent Tech- nologies National Customer Care Center support line at 1-800-643-2353. Outside the ... See full document

... Each of the three main categories have subcategories listed under them that when set to a “y” give permission to use the command sets associated with that category. When the Command Permissions Categories form is ... See full document

... Client applications use CVLAN client side library to establish communication with a server. This process is nearly identical to that used with the CallVisor PC ASAI library (server addresses must be ... See full document

... If a room is excessively noisy, the DEFINITY MMCH may receive sufficient audio signal to conclude that there is a speaker present. Use the Status Conference x form to determine if the MMCH thinks an endpoint is ... See full document

... The maximum range for out-of-building digital voice terminals is 3400 feet (1036 m) when using 24 AWG (#5) (0.26 mm 2 ) wire and 2200 feet (670 m) when using 26 AWG (#4) (0.14 mm 2 ) wire. The range can be extended to ... See full document

... Note that regardless of the number of ISDN boards installed in the computer, the same IRQ/IVN number is used. Matching Versions Requirement for the ISDN protocol stack, specifically for the QP module, must be done ... See full document

... To save the recorded announcements in the system, type save announcements and press Enter . Use these codes after business hours or when the system is operating during a low-usage period. The system takes about 40 ... See full document

... 3. Read and follow any directions inserted into the package by the factory. The TN802B external cable assembly is a bundle of cables with an amphenol connector at the end of the bundle and various PC-type ... See full document

... Under DOS (and Windows, which works cooperatively with DOS), the serial port interfaces in a PC are uniquely identified by specific device names: COM1 ("serial communications port 1"), COM2 ("serial ... See full document