• No results found

[PDF] Top 20 Design and Optimization of Silo using FEM

Has 10000 "Design and Optimization of Silo using FEM" found on our website. Below are the top 20 most common "Design and Optimization of Silo using FEM".

Design and Optimization of Silo using FEM

Design and Optimization of Silo using FEM

... The goal of modal analysis in structural mechanics is to determine the natural mode shapes and frequencies of an object or structure during free vibration. It is common to use the finite element method (FEM) to ... See full document

8

Optimal Design Of A Fabric Shell Using A Coupled Fem-Optimization Procedure

Optimal Design Of A Fabric Shell Using A Coupled Fem-Optimization Procedure

... and design of this complex structure by using Finite element method ...sections design obtained according to the Standards ...on using Ansys ... See full document

5

Optimization Of Geometric Design Of A Linear Type Motion Electrostatic Actuator Using Finite Element Method (FEM)

Optimization Of Geometric Design Of A Linear Type Motion Electrostatic Actuator Using Finite Element Method (FEM)

... that, FEM analysis is required to tally the development of electrostatic actuator mechanism with the software analysis such that both must meet the minimum requirement especially knowing the loss of energy in the ... See full document

24

Design and optimization of automobile propeller shaft with composite materials using FEM Analysis

Design and optimization of automobile propeller shaft with composite materials using FEM Analysis

... Deepti kushwaha & Gaurav Saxena [11] They investigate that The weight reduction of the drive shaft can have a certain role in the general weight reduction of the vehicle and are a highly desirable goal. Substituting ... See full document

10

Design Optimization of Axial Flux Permanent Magnet (AFPM) Synchronous Machine Using 3D FEM Analysis

Design Optimization of Axial Flux Permanent Magnet (AFPM) Synchronous Machine Using 3D FEM Analysis

... equations. Using nonlinear 3D FEM electromagnetic analysis, the selected AFPM models preserving all properties and dimensions except the magnet shape were ... See full document

15

Design Shape Optimization to Ceramic Turbine Vane Using Fem and Matlab
P Ramakrishna & P Santhi

Design Shape Optimization to Ceramic Turbine Vane Using Fem and Matlab P Ramakrishna & P Santhi

... Naeem et al. [2] carried out the failure analysis of gas turbine blades made of nickle-base alloy in two discrete sections, they are Mechanical and Metallurgical by using Ansys work bench software and ... See full document

10

Design, Optimization and FEM Analysis of a Surface-Mounted Permanent-magnet Brushless DC Motor

Design, Optimization and FEM Analysis of a Surface-Mounted Permanent-magnet Brushless DC Motor

... [4]. Design, optimization, numerical analysis and torque capability study for BLDC motor is also discussed in literature [5, ...investigated design of a high-efficiency minimum-torque-ripple ... See full document

7

Design and Optimization of RCC Silo

Design and Optimization of RCC Silo

... Silo has been used to store bulk solids (such as cement, coal, bitumen, etc) in industries. The quantity may range from few tones to over one hundred thousand tones. Shallow bins are usually called as bunkers and ... See full document

11

OPTIMIZATION OF HEAVY TRUCK CHASSIS DESIGN PARAMETERS USING FEM

OPTIMIZATION OF HEAVY TRUCK CHASSIS DESIGN PARAMETERS USING FEM

... 1. Dave Anderson and Grey Scheme, “Development of a Multi- Body Dynamic Modal of a Tractor – Semi trailer for Ride Quality Prediction”, International Truck and Engine Corp. 2001. 2. I.M. Ibrahim, D.A.Crolla and D.C. ... See full document

11

Parametric Design of a Jig & Fixture Using CAE and FEM Analysis of Positioners and Clamping

Parametric Design of a Jig & Fixture Using CAE and FEM Analysis of Positioners and Clamping

... major optimization has been carried out, and that for further evaluation of the clamping and positioners, it is possible to include some changes in the ...analysis. Using this capability, the designer can ... See full document

10

Optimization of frameworks by means of fem use

Optimization of frameworks by means of fem use

... an optimization procedure for a mass optimization of a welded framework of a special tractor trailer designed for transport of seeding ...used optimization procedure, so-called Fully Stressed ... See full document

5

Optimization Of Crane Cross Sectional Area By Using Bem And Fem

Optimization Of Crane Cross Sectional Area By Using Bem And Fem

... by using the equations in table. 1, and the maximum deflection by using equation ...The design and the programming are shown in figure (3) and (4) ... See full document

10

Optimization of Double Track Railway Bridge Superstructure Using FEM

Optimization of Double Track Railway Bridge Superstructure Using FEM

... The design of bridges should be done for actual wheel loads, but theoretically it is very difficult to analyse the bridge at actual wheel ...optimal design with respect to shape and size of structural ... See full document

7

Design Optimization of Two Synchronous Reluctance Machine Structures with Maximized Torque and Power Factor

Design Optimization of Two Synchronous Reluctance Machine Structures with Maximized Torque and Power Factor

... The aim is to optimize two rotor structures of SynRM. Both of the rotors fit in a standard 4 pole — three phase induction machine stator. Main design details of the induction motor are given in Table 1. The ... See full document

19

Optimization of Working of Processor by Fins  Using FEM

Optimization of Working of Processor by Fins Using FEM

... electronics design and to explore the thermal design space, analyzed the finite element numerical simulations, physical experimentation, and analytical ...convection using a widely used computational ... See full document

7

DESIGN AND ANALYSIS OF CAR PROPELLER SHAFT BY USING FEM

DESIGN AND ANALYSIS OF CAR PROPELLER SHAFT BY USING FEM

... is design by manufacturer according to its suitable engine power & also loads carrying capacity and models, because various type of Propeller shaft is available for different types of ... See full document

5

Product Design using a Contact-Optimization Technique

Product Design using a Contact-Optimization Technique

... Sub-section 2.3 o f this paper deals with the w e a r p ro b le m o f the re la tiv e s lid in g o f tw o contacting bodies. The transmittable torque with a clutch and frictional power loss in the case o f brakes are ... See full document

20

The Design and Optimization of Automated Storage and Retrieval Systems

The Design and Optimization of Automated Storage and Retrieval Systems

... Unfortunately, in the past, warehousing, transport systems and transferring processes were neglected, and this nowadays shows itself in a relatively low degree of automation in comparison with the production process. ... See full document

24

Design and Analysis of Car Disc Brake by Using FEM

Design and Analysis of Car Disc Brake by Using FEM

... The present study can provide a useful design tool and improve the brake performance of disk brake system. From the above Table we can say that all the values obtained from the analysis are less than their ... See full document

9

The SILO Architecture: Exploring Future Internet Design.

The SILO Architecture: Exploring Future Internet Design.

... The Internet, conceived in the era of mainframe computers and 56Kbps links, has evolved into a complex world-wide system of importance equal to that of the power grid and the transportation infrastructure. The Internet’s ... See full document

144

Show all 10000 documents...