• No results found

[PDF] Top 20 DESIGN AND TOPOLOGY OPTIMISATION OF A STEERING KNUCKLE JOINT USING FEA

Has 10000 "DESIGN AND TOPOLOGY OPTIMISATION OF A STEERING KNUCKLE JOINT USING FEA" found on our website. Below are the top 20 most common "DESIGN AND TOPOLOGY OPTIMISATION OF A STEERING KNUCKLE JOINT USING FEA".

DESIGN AND TOPOLOGY OPTIMISATION OF A STEERING KNUCKLE JOINT USING FEA

DESIGN AND TOPOLOGY OPTIMISATION OF A STEERING KNUCKLE JOINT USING FEA

... of steering knuckle targeting reducing weight as objective function with required strength, frequency and ...a steering knuckle is that part which contains the wheel hub or spindle, and ... See full document

6

Weight Optimization of Steering Knuckle Joint using Fea

Weight Optimization of Steering Knuckle Joint using Fea

... There are several materials used for manufacturing of steering knuckle such as S.G. iron (ductile iron), white cast iron and grey cast iron. But grey cast iron mostly used. Forged steel are most demanding ... See full document

6

Design Optimisation of a Steering Knuckle Component Using Conservative Method of Finite Element Analysis

Design Optimisation of a Steering Knuckle Component Using Conservative Method of Finite Element Analysis

... Creo Parametric is a computer graphics system for modeling various mechanical designs and for performing related design and manufacturing operations. The system uses a 3D solid modeling system as the core, and ... See full document

10

Predicition of Fatigue Life Cycle on Steering Knuckle Ball Joint

Predicition of Fatigue Life Cycle on Steering Knuckle Ball Joint

... The objective of the stress analysis was to obtain the complete three dimensional stress and strain distributions at a potential failure site, facilitating fatigue life predictions. Depending upon the method used for ... See full document

7

Design & Fabrication of Front Wheel Upright Assembly for an ATV

Design & Fabrication of Front Wheel Upright Assembly for an ATV

... as design and fabrication of Front Wheel Upright Assembly for an ATV (all-terrain ...the design of wheel hub and upright ...of design and CAE analysis of the components & features the image ... See full document

5

Design of Suspension Ball Joint Using FEA and Experimental Method

Design of Suspension Ball Joint Using FEA and Experimental Method

... Ball joint is an important part of car suspension ...ball joint is one moveable part of a control arm ...the steering knuckle and the latter connects the ...for steering and vertically ... See full document

6

Material Optimization of Wheel Hub using Finite Element Analysis

Material Optimization of Wheel Hub using Finite Element Analysis

... by FEA we can check its strength, rigidity and factor of safety for our product By use of FEA we don’t have to perform Destructive test again various load condition and is also time saving analysis process, ... See full document

7

Fatigue Analysis Of Steering Knuckle

Fatigue Analysis Of Steering Knuckle

... independent design of front suspension. One of those design is the swing axle suspension which is shown in figure ...This design was used by some sports car in the 50s such as the Mercedes 300SL ... See full document

24

Improving rockbolt design in tunnels using topology optimisation

Improving rockbolt design in tunnels using topology optimisation

... 169 It should be noted that as a two dimensional model is considered here, the obtained 170 optimisation outcomes are bolt cross section areas per unit length of the tunnel.. When 171 tr[r] ... See full document

42

3. A STATIC STRUCTURAL ANALYSIS OF KNUCKLE JOINT USED FOR SUGARCANE MILL

3. A STATIC STRUCTURAL ANALYSIS OF KNUCKLE JOINT USED FOR SUGARCANE MILL

... of knuckle joint. The Knuckle joint assembly consists of components such as Single eye, Fork (Double eye), Knuckle pin, Collar, Tapper ... See full document

13

Optimization and Fatigue Analysis of Steering Knuckle

Optimization and Fatigue Analysis of Steering Knuckle

... Steering knuckle or hub carrier is a forging that usually includes the spindle and steering arm, and allows the front wheel to ...The knuckle is bestrode within the upper and lower ball joints ... See full document

5

Optimization of Baja Racing Car Front Suspension Parameters Based on ADAMS

Optimization of Baja Racing Car Front Suspension Parameters Based on ADAMS

... Baja SAE China, or BSC for short, is a college student SUV race sponsored by China Society of Automotive Engineer. The participating teams are required to create a small SUV that complies with the competition rules ... See full document

5

Design And Development Functional Prototyping Formula SAE Knuckle

Design And Development Functional Prototyping Formula SAE Knuckle

... The knuckle design must be reduce weight and maximized the ...the design must be ease to ...suitable design to ensure the knuckle can be use and fitted to the SAE ...The design ... See full document

24

Structural Analysis of Steering Knuckle for Weight Reduction

Structural Analysis of Steering Knuckle for Weight Reduction

... investigation, steering knuckle was used as component for ...materials, design and analysis methods, fabrication processes and optimization techniques, ...etc. Steering Knuckle is ... See full document

6

Optimization of Steering Knuckle for Off Road Vehicle

Optimization of Steering Knuckle for Off Road Vehicle

... - Steering Knuckle is a non-standard component linking the suspension, steering & braking systems and the wheel hub to the chassis of a ...the steering knuckle in order to reduce ... See full document

8

Weight Optimization of Steering Knuckle for Four Wheelers

Weight Optimization of Steering Knuckle for Four Wheelers

... of steering knuckle, it is necessary that one should look into the aspects of design and the available literature for understanding the industries need for the reduction of weight of the components ... See full document

7

Design of a truss bridge for low cost using structural topology optimisation

Design of a truss bridge for low cost using structural topology optimisation

... The Australian engineer Anthony Michell’s 1904 paper “The limit of economy in frame structures” is considered the birth of structural topology optimisation. In this paper Michell developed general ... See full document

150

Developmental Design and Optimization of Steering Knuckle with Integrated Spindle

Developmental Design and Optimization of Steering Knuckle with Integrated Spindle

... The experimental investigation is performed on fabricated prototype on universal testing machine (UTM) at Praj Metallurgical Lab, Kothrud, Pune. Compression test and axial test has been performed on the prototype of ... See full document

5

Material Optimization for Knuckle Joint by using FEA

Material Optimization for Knuckle Joint by using FEA

... (finite element) tool for structural analysis, including linear, nonlinear and dynamic studies. The engineering simulation product always provides a complete set of elements behavior, material models and equation solvers ... See full document

8

Design and Analysis of Bearing Assembly in Knuckle Steering using sensor

Design and Analysis of Bearing Assembly in Knuckle Steering using sensor

... both knuckle and bearing (ABS or Non-ABS), when both signals are similar then the pressing machine will engage the ...ABS knuckle having machined portion and the Non-ABS knuckle having un- machined ... See full document

5

Show all 10000 documents...