[PDF] Top 20 Effect of Caries Removal Methods on the Shear Bond Strength of Resin and Glass Ionomer Adhesives to Primary Dentin

... the effect of applying Carisolv on shear bond strength of different adhesive systems, Erhardt et ...demineralized dentin to Carisolv, Dammaschke et ...the dentin is protected by ... See full document

... Dental caries are the most pervasive microbiological disease in the ...secondary caries have been quoted as one of the most common causes of restoration ...the shear bond strength of ... See full document

... of dentin and monomer penetration into dentin sub- ...nano ionomer perhaps behaves more like a resin composite rather than a true glass ionomer [3, ...of shear bond ... See full document

... composite resin replaced it as the primary direct esthetic filling ...cement. Glass ionomer cements were invented in 1968 and first described by Wilson & Kent in ... See full document

... were primary canine and first molars close to their physiologic exfolia- tion time, over-retained teeth and teeth that were candidates for serial ...extensive caries, and with broken crowns were ...expose ... See full document

... to dentin is somewhat different; so that they attach to the dentin through a chelation reaction, followed by metal ion exchange, and formation of a layer between the GI and tooth ...microtensile bond ... See full document

... and Methods: In this in vitro study, 72 premolar teeth without caries or restorations were selected and randomly divided into six groups of 12 ...of dentin surface. The remaining groups received ... See full document

... and Methods: In this in-vitro study, 60 intact extracted human premolars were ...and dentin of the buccal surface was ...1-3, dentin was exposed to CHX and in groups 4-6, dentin was exposed to ... See full document

... e adhesives (Si ngl e Bond and XP Bond) and two s elf -et ch adhesi ves (Prompt L -Pop and Xeno III) were emplo yed to bond the compos ...ite. Shear bond st rengt h (S BS ) was ... See full document

... ment (Kuraray Noritake Dental Inc., Kurashiki, Japan), pastes A and B were mixed according to the manufactur- er’s instructions, and applied to the TYGON microtubes using a fine plugger. The TYGON tubes filled with the ... See full document

... Most advances of technology have provided the possibility of creating high power LEDs (HP) which claim for reduced curing time. To achieve this reduction, new LEDs have external intensity of up to 1000 mw/cm². Since all ... See full document

... Then shear forces were applied to the brackets of all 4 groups, including three study groups and one control group, using a universal testing machine (Walter+bai, Switzerland) at ...the bond failure ...a ... See full document

... After calculation of the means and standard deviations of weight percentages of silver accumulation at the gingival mar- gin of each group, SPSS (v 20, IBM Corporation, Armonk, NY, USA) was used for statistical analysis. ... See full document

... In the present study, the non - alcoholic mouth rinses were selected to avoid the proven adverse effects of alcohol containing mouthrinse on the restorative materials. During the usage of mouth rinse, it comes in brief ... See full document

... Forty-eight specimens were prepared from freshly extracted bovine incisors. The bovine teeth were collected as anonym- ous by-products of regular slaughtering of the cattle for hu- man food consumption. Enamel blocks (4 ... See full document

... modified resin composite, or compomer (Dyract) and three resin modified glass ionomer cements (Fuji II LC, Photac-Fil, and Vitremer) and to compare the use of 3 units for measuring fluoride ... See full document

... and glass slap in order to put the GIc and the acryl- ic molding at the same ...adhesive resin was applied on the surface of GIc (all according to manufacturer's instruction) (Figure ...the adhesives ... See full document

... this bond could be compromised because sealed dentin surfaces have the potential to strongly attach to resin-based provisional materials, suggesting that this type of provisional material should be ... See full document

... the effect of the materials (Fuji Ortho LC and Transbond XT) at a depth from the enamel surface (10, 20, 30, 60 and 90 µm) position (under the bracket, on the buccal surface, in occlusal and cervical region at 0, ... See full document

... is Dentin surface contamination can occur at two critical situations during the bonding procedure, after the tooth surface has been etched, and / or after the adhesive system had been ...negative effect of ... See full document