[PDF] Top 20 Effect of Hydrostatic Pressure on the Pitting Corrosion Behavior of 316L Stainless Steel

... ordered pitting depth in ...of pitting growth mechanism (deep-hole shape and hemispherical shape) undertook on 316L SS ...largest pitting cavities ...stable pitting depth expected from ... See full document

... on pitting corrosion behavior of low-alloy steel under hydrostatic pressure in neutral ...combined effect of hydrostatic pressure and dissolved oxygen ... See full document

... given pitting depth occurring under each of the two hydrostatic test pressures was calculated using ...a pitting cavity with a particular depth to occur by taking the reciprocal of the ...μm ... See full document

... of corrosion [2]， Furthermore, the erosion-corrosion occurs the synergistic effects of corrosion and wear, which is complex electrochemical and mechanical mechanisms, causing a higher damage of the ... See full document

... The effect of temperature on the passive behavior of stainless steel has been studied by a lot of ...the corrosion potential increase from -293mV to -256mV (Ag/AgCl) when temperature ... See full document

... of corrosion behaviors of steels in weak acid environments is currently a hot research ...the corrosion behavior of mild steel in carbonic and acetic acid solutions and concluded that carbonic ... See full document

... resistance, corrosion resistance and dimensional stability ...in corrosion resistance, and decreases in the coefficient of friction, reduced creep and improved machinability ... See full document

... gas pressure maintained at 0.3 atm.using precision digital gas pressure controller ...gas pressure increased above ...gas pressure back to ...for 316L and 15minute for ... See full document

... time. Stainless steel 316L (SS316L) is used for the main pipeline due to its mechanical properties, ability to withstand high temperatures, and uniform resistance to ...the stainless ... See full document

... and pitting corrosion of 316L SS in NaCl ...marked pitting corrosion inhibition. The corrosion inhibition behavior of MBI argued to the formation of MBI layer, which can ... See full document

... the corrosion surface, and area 3 was taken from the substrate of the SS316L SLM ...initial 316L state. It could be considered that the effect of Cr and Mn seemed to inhibit the activity of Fe, Mo ... See full document

... the corrosion process compared to that of without the compressive ...the stainless steel and the aluminum alloy, the role of compressive stress might be same as far as an auxiliary role for the ... See full document

... for 316L-CR were higher than those for 316L-SA at each ...for 316L-CR to those of 316L-SA decreased with applied ...of 316L SS, and the effect of cold roll was more obvious under ... See full document

... a 316L stainless steel-made dairy reactor contributed to the development of significant pitting, which was entirely confined to the welding zone of the ...of pitting was found outside ... See full document

... electrochemical behavior of 316L stainless steel alloy was performed by open circuit potential, electrochemical impedance spectroscopy, potentiodynamic polarization measurements and surface ... See full document

... Stainless steel of AISI 316L type (SS316L) has been widely used as metallic biomedical implants material because of it offers good characteristics, including high mechanical properties and ... See full document

... Pitting corrosion can be analyzed using electrochemical noise ...mild steel and stainless steel samples were immersed in NaCl ...mild steel sample to create a passivating layer ... See full document

... metastable pitting behavior indicated above ...316-L steel manufactured by them and in this paper a commercial alloy was ...that pitting potential is 100 mV [22], or 850 mV in tests at 18°C ... See full document

... scanning rate setting was 1 mV·s ¹1 , and scanning potential range was from the initial potential of ¹1.5 to 1.5 V versus open-circuit potential and stopped at the final current-density of 1.0 © 10 ¹ 2 A·m ¹ 2 as well as ... See full document

... in the potential range between -0.2 and +0.8 V vs. SCE. The inhibitor addition reduces the anodic and cathodic current’s densities, shifts the corrosion potential to noble values and varies the Tafel’s slope ... See full document