[PDF] Top 20 Evaluation of a New and Advance Curing Light on the Shear Bond Strength of Orthodontic Brackets

... of curing time per bracket has been recommended to allow for adequate polymeriza- tion with a conventional halogen light source, resulting in a considerable amount of chair time if one or both arches are ... See full document

... of light-curing units with dif- ferent spectral profiles and light ...intensity light may lead to inadequate depth of cure and insufficient bond strength, high-intensity ... See full document

... each. Brackets (Discovery, Dentaurum, Germany) were bonded in group 1 (total-etch-system, Transbond XT) and in group 2 (self-etch-system, Tectosan) with curing light for 40 ...s. Shear bonding ... See full document

... twin brackets, American Orthodontics, Sheboygan, WI, USA) was bonded with a Transbond XT adhesive (3M Unitek, ...and light‑cured (Bonart‑Art‑L2 Light Curing Unit, Bonart ...No bond ... See full document

... properties(bond strength), clinical performance(failure rate) and biological properties of blue light are reviewed to know their clinical usefulness in application to orthodontic ...The ... See full document

... direct bonding in fixed orthodontic treatment [3]. In conventional acid-etch (AE) technique, three components are used: etchant, primer, and adhesive. The most widely accepted etchant is 37% phosphoric acid. The ... See full document

... halogen light curing systems [9]. Despite their popularity, halogen light curing units have several ...their light power output is 1% of the total electric energy consumed ...of ... See full document

... of brackets and ...to bond the metal brackets. After proper positioning of the brackets in both groups, the brackets were exposed to light cure (EliparTM S10 LED Curing ... See full document

... for orthodontic purpose were divided into four groups, according to the light-curing unit and exposure times ...were light cured for 20 and 40 ...were light cured for 5 and 10 seconds. ... See full document

... lesions during treatment that lasts approximately for 2 years, while smooth surface lesions increase up to 50% in preva- lence during treatment [2]. Fluoride-containing dentifrice and fluoridated mouthwash has shown to ... See full document

... of bond failure amongst all ...their bond failures occur either at or near the restoration-adhesive interface (ARI = 0 or 1), indicating a weaker bond at the surface of the ...of bond failures ... See full document

... using orthodontic brackets and measured shear bond strength values of ...good bond with zirconia. The scotch bond universal self-etch adhesive also contains 10- ... See full document

... the shear bond strength of the brackets bonded with adhesive and flowable composites under contamination by human blood and human saliva& to evaluate enamel damage post debonding using ARI ... See full document

... the bond strength of orthodontic attachments to composite resin surfaces such as the type of composite resin, the film thickness of adhesive resin, moisture, contamin- ation, the dimension and ... See full document

... adequate bond strength for orthodontic bracket bonding, presenting similar strength to that obtained with phos- phoric acid etching [30] ...satisfactory bond strength to enamel ... See full document

... Pre-treatment of ceramic surfaces is necessary to obtain sufficient strength to bond orthodontic brackets to all ceramic restorations. Several options have been described which are generally ... See full document

... With the emergence of nanotechnology and the different behavior expressed by nanoparticles, attempts have been made to take advantage of this concept in orthodontic bonding. Nano sized materials are attracting a ... See full document

... around brackets and bands have become a major concern during orthodontic treatment especially with the potential of these lesions to develop into caries when oral hygiene maintenance is ...During ... See full document

... the shear bond strength of orthodontic ...the shear bond strength ...in strength than the control group (not ...the bond strength of brackets ... See full document

... powerful light curing devices [2]. Many light cured bonding materials have become popular but it is the need of the hour to determine the bonding agent that is the most efficient and has the desired ... See full document