[PDF] Top 20 Evaluation of Shear Bond Strength of Composite to Feldspathic Porcelain after Porcelain Surface Treatment with CO2 and Er:YAG lasers
Has 10000 "Evaluation of Shear Bond Strength of Composite to Feldspathic Porcelain after Porcelain Surface Treatment with CO2 and Er:YAG lasers" found on our website. Below are the top 20 most common "Evaluation of Shear Bond Strength of Composite to Feldspathic Porcelain after Porcelain Surface Treatment with CO2 and Er:YAG lasers".
Evaluation of Shear Bond Strength of Composite to Feldspathic Porcelain after Porcelain Surface Treatment with CO2 and Er:YAG lasers
... and feldspathic porcelain of ceramic-metal ...the- shear bond strengthof composite resin to feldspath- ic porcelain after porcelain surface treatment ... See full document
5
Influence of Different Power Outputs of Er:YAG Laser on Shear Bond Strength of a Resin Composite to Feldspathic Porcelain
... each porcelain block. Subse- quently, any excess resin composite was carefully re- moved from periphery of the tubes with a sharp surgi- cal ...polymerization. After the composite buildup, the ... See full document
7
In Vitro Evaluation of the Effect of Different Sandblasting Times on the Bond Strength of Feldspathic Porcelain to Composite Resin
... the bond strength of resin to feldspathic ceramic [3, ...micro-shear bond strength values in feldspathic porcelain surface etched with hydrofluoric acid and ... See full document
8
Effect of Thermocycling on the Flexural Strength of Porcelain Laminate Veneers
... biocompatibility, surface hardness, light absorp tion, light scattering behavior and low electrical and thermal ...sections. Porcelain laminate veneers were thus developed and which is presently considered ... See full document
98
Bond strength of a universal bonding agent and other contemporary dental adhesives applied on enamel, dentin, composite, and porcelain
... than ER versions [2], it has been shown that both techniques may lead to appropriates dental bonding ...the bond strength results when using the universal adhesive tested ... See full document
10
A Comparison between Shear Bond Strength of VMK Master Porcelain with Three Base-metal Alloys (Ni-cr-T3, VeraBond, Super Cast) and One Noble Alloy (X-33) in Metal-ceramic Restorations
... evaluate shear bond strength of the specimens, they were fixed on a metal jig and subjected to three-point bending test [8] Figure ...the porcelain was in the opposite ...1c. Shear ... See full document
6
Effect of oral environmental conditions on surface roughness and fatigue strength of porcelain fused to metal restorations
... the surface quality as well as fatigue strength of ...on surface roughness and fatigue ...of porcelain was tested by measuring the surface roughness using the ...fatigue strength ... See full document
5
A comparative evaluation of shear bond strength of the porcelian laminates using different surface treatments: an in vitro study
... silane treatment increased almost 5 times higher bond strength than that of acid etched porcelain surface (Lee, ...The bond with ceramics occurs via condensation reaction between ... See full document
5
The effects of reduction atmospheres upon feldspathic glazed porcelain forms
... Porcelain Bottle Copper Blue Reduction Glaze Mark, Impressed Carbon, and Separations Bottle Green Lava Reduction Glaze and Impressed Carbon with 20 Fire Circular 21 with Flowing 22 Bowl [r] ... See full document
33
Comparison of the Effect of Feldspathic Porcelain and Zirconia on Natural Tooth Wear
... the surface hardness and the friction coefficient of a dental material to estimate its abrasiveness and wear of the opposing teeth ...its surface characteristics, surface roughness of the restoration ... See full document
7
Evaluation the Effect of Different Surface Treatment on Shear Bond Strength between Composite Increments (An in vitro study)
... universal bond (one bottle technique),this system represent the seven generation in bond classification which characterize by join acid etch, prime, and bond agent in one bottle ,this system first ... See full document
10
Manufacture of composite board using wood prunings and waste porcelain stone
... stone composite board, which has excellent waterproof property and incombustibility ...wood– porcelain stone composite board as a construction material and evaluated the physical and mechanical ... See full document
6
The properties of feldspathic dental porcelain from Tanzanian aluminosilicate materials
... fusing porcelain are used for metal-ceramic ...typical feldspathic dental porcelain by weight is; feldspar (75-85%), quartz (12-22%), kaolin (3-5%) and metallic pigments which increase opacity of ... See full document
6
Microshear Bond Strength of Transbond XT and Assure Universal Bonding Resin to Stainless Steel Brackets, Amalgam and Porcelain
... 20 feldspathic porcelain specimens and 20 self-cure acrylic cavities filled with amalgam were divided into 2 groups bonded with Transbond XT and ...Assure. After surface preparation in each ... See full document
5
Comparison of shear bond strength of veneering ceramic to zirconia after surface treatment with air abrasion and laser treatment: An In vitro study
... as feldspathic, glass–ceramic, and glass-infiltrated ceramic ...as feldspathic porcelain, offer excellent optical qualities and are, hence, applied in situations of highest aesthetic ... See full document
116
Evaluation of Shear Bond Strength of Methacrylate- and Silorane-based Composite Resin Bonded to Resin-Modified Glass-ionomer Containing Micro- and Nano-hydroxyapatite
... lorane-based composite resin to ...the shear bond strength of silorane-based composite resin (Filtek LS) to RMGI versus Z250/Adper Scotch Bond ...silorane composite resin ... See full document
7
Influence of Preparation Design and Restorative Material to Marginal Discrepancy of Ceramic Laminate Veneers
... proximal surface Of each metal die with a more specific (light polymerized Hanan-wolfgang, Germany) with Relief mm3, the Silicone material (Speedex; Colten, Swiss) 30 times done molding ... See full document
6
Comparison of Bond Strength of Porcelain Laminate Veneers Bonded to Laser Treated Dentin and Acid Treated Dentin : An In Vitro Study
... las er. Two etch and rins e adhesives (Si ngl e Bond and XP Bond) and two s elf -et ch adhesi ves (Prompt L -Pop and Xeno III) were emplo yed to bond the compos ...ite. Shear ... See full document
86
Effect of Type of Surface Treatment and Adhesive System on Shear Bond Strength of Composite Resin to a Non-Precious Metal Alloy
... of porcelain in metal ceramic restorations may occur. Porcelain fracture may be seen in the form of delamination, fracture or chipping of the veneering porcelain ...the porcelain veneering is ... See full document
8
Effect of Laser Irradiation on Bond Strength of Zirconia Ceramic to Self-Adhesive Resin Cement
... No treatment, (II) sandblasting plus neodymium-doped yttrium aluminum garnet (Nd:YAG) laser (1 W), (III) sandblasting plus Nd:YAG laser (2 W), (IV) Nd:YAG laser alone (1 W), (V) Nd:YAG laser alone (2 W), and (VI) ... See full document
6
Related subjects