[PDF] Top 20 Influence of Cutting Fluids on the Corrosion Resistance of X20Cr13 Martensitic Stainless Steel

... used cutting fluid quantities opens up numerous ecological issues, especially when taken into account that it is one of the most complex types of waste with a high organic charge ...of cutting fluids ... See full document

... Martensitic stainless steels are used for surgical and dental instruments, wire, springs, blades, fasteners, gears and ball ...moderate corrosion resistance allow these steels to be used in a ... See full document

... by corrosion processes and the interaction of corrosion with the mechanical ...the influence of corrosion on abrasive wear and utilises a recently developed experimental technique which ... See full document

... Martensitic stainless steels are used for surgical and dental instruments, wire, springs, blades, fasteners, gears and ball ...moderate corrosion resistance allow these steels to be used in a ... See full document

... the corrosion pitting and repassivation behavior of the samples, cyclic potentiodynamic polarization (CPP) scans were conducted on each of the samples to explore the effects of the differing heat ...ranked ... See full document

... Finally, it can be concluded that the same mechanisms of wear are observed under both dry and argillaceous paste conditions. The difference in the wear rates can be attributed to the microstructure and its features. On ... See full document

... mild steel in 5% NaCl solution with and without inhibitor was investigated by electrochemical impedance spectroscopy measurements are presented in Table ...transfer resistance (R t ) is found to increase ... See full document

... duplex stainless steels, different pass of welding thermal cycle could lead to the evolution of microstructure, ...the corrosion resistance of ferrite and austenite ...duplex stainless steels, ... See full document

... in the potential range between -0.2 and +0.8 V vs. SCE. The inhibitor addition reduces the anodic and cathodic current’s densities, shifts the corrosion potential to noble values and varies the Tafel’s slope ... See full document

... high corrosion resistance in comparison to carbon steels due to varying weight content of chromium, nickel ...metal. Martensitic grades of stainless steels exhibit superior mechanical ... See full document

... Dissimilar metal welding has gained its popularity and well-established in catering the requirement of transition in mechanical properties and/or variation of service environments (Lippold and Kotecki, 2005). This method ... See full document

... the corrosion properties of these alloys in saline solution for application as new friendly environmentally sacrificial coatings in the pro- tection of steel ...the corrosion rates of this alloy. [2] ... See full document

... and stainless steels may be used as corrosion-resistant ...carbon steel rebars with a Ni alloy coating holds the promise for a cost-effective solution to chloride-induced corrosion ...wear ... See full document

... various fluids were also analyzed to determine the properties and constituent elements of the cutting ...the stainless steel bar was done using a Colchester mastiff lathe ...and cutting ... See full document

... Stainless steel plate was cut in dimensions of 200 X 400mm with a hydraulic saw machine using a cooling liquid then the sample’s edges to be bonded were chamfered at 30 o ... See full document

... pitting corrosion and the crevice corrosion were largely suppressed by the application of US in the solution, and the corrosion current density changed almost synchronistically with the cyclic ... See full document

... the current density peak is observed in the cyclic vol- tammograms. Consequently, a good relationship existed between EIS and cyclic voltammograms. In Figure 5, the resistances of as-received specimens are always higher ... See full document

... pitting corrosion.[1] In general, it indicated a curve type of ferrite stainless steel polarization, which started from the nearly same potential, since the passive film formation potentials made no ... See full document

... the corrosion polarization values obtained, as shown in Table 2 and ...higher corrosion current density (icorr) value of ...polarization resistance, Rρ, of ...higher corrosion rate of ... See full document

... inferior corrosion resistance compared with the base metal (Figure ...the corrosion behavior of such weld metals (Kim et ...the corrosion resistance (Pujar et ... See full document