[PDF] Top 20 ND-70895 (E) ISSUE 1 STOCK # 200876 OAI System Manual

... The SCF is the facility that executes, from the Application Program (AP), such control operations as connections/disconnections between NEAX2400 IMX-accommodate terminal (D term ) and another, between a D term and a C.O. ... See full document

... the system, and sends out information about the detected alarm to the circuits ...the system MJ/MN LEDs on the ...the 1 IMG system, this circuit card has the Music-On-Hold sending ... See full document

... Figure 4-11 shows sample cable connections, where HUB (PA-M96) cards are provided in a dual configu- ration and the FCH (PA-FCHA) card is located in PIM 1 (1-IMG system/IMG0). When HUB cards are pro- ... See full document

... The CPU sends diagnosis data at periodic intervals to the Port Microprocessor (PM) on the FCH (PA-FCHA) cards to monitor the PM. If the CPU cannot receive the return data within a predetermined time, the system ... See full document

... In the PBX, all line/trunk circuits are provided by installing the cards into a card shelf. The PBX employs a flexible port assignment architecture in which the system allocates a port (Time Slot) to each LEN ... See full document

... The connection to ground of the supplementary equipment grounding conductor shall be in compliance with the rules for terminating bonding jumpers in Part K of Article 250 of the National Electrical Code, ANSI/NFPA 70. ... See full document

... Note 5: When the DCE connected to the port does not provide a function to send the DSR signals, set the switch to ON. In this case, the AP00 card can not recognize the actual state of the DCE, so that the call records or ... See full document

... the system is initialized by “C” (Resident System Program), every Multiline Terminal will be able to go into CAT ...the system is initialized by “B” (All Clear), only LEN0000 is assigned as a CAT ... See full document

... the system layout and floor layout in this manual according to customer’s ...Programming Manual, Command Manual and Installation Procedure ... See full document

... mode. System data can be programmed so that once the ATTENDANT CONSOLE [A-3] has entered the NIGHT CONNECTION [N-1, 2] mode, a station's CLASS OF SERVICE – INDIVIDUAL [C-15] will be automatically changed as ... See full document

... F1032 OAI Function Key Number 1 F1033 OAI Function Key Number 2 F1034 OAI Function Key Number 3 F1035 OAI Function Key Number 4 F1036 OAI Function Key Number 5 F1037 OAI ... See full document

... Event Based CCIS allows a PBX customer who does not have a tie line (or when a customer can not use the tie line due to the busy or fault of the line), to use the various CCIS feature by using the ISDN line as a CCIS ... See full document

... The maximum number of Wireless PS stations has been expanded from 168 to 250 when an Integrated type system is being used. Previously, each PS line reduced the capacity of CM10 by three ports [One port for CM1C ... See full document

... PFT0 26 Sta. T0 1 Sta. R0 27 4LC. T0 2 4LC. R0 28 C.O. T0 3 C.O. R0 29 4COT. T0 4 4COT. R0 30 Sta. T1 5 Sta. R1 31 4LC. T1 6 4LC. R1 32 C.O. T1 7 C.O. R1 33 4COT. T1 8 4COT. R1 34 Sta. T2 9 Sta. R2 35 4LC. T2 10 ... See full document

... the system is configured with two or more PIMs, the BUS cable provides gang control for the PZ-PW121 card of PIM0 and other ...whole system even when the power switch(es) of other PIMs are left ...the ... See full document

... Data 1, Index 14 determines the algorithm used to calculate the last two digits of every AUTHORIZATION ...assigned). System Data 1, Index 14 = X & Y, where X and Y represent any arbitrarily ... See full document

... switching system operates in an environment that does not meet these specifications, the reliability of the switching equipment may be ...the system, or if the temperature or humidity fluctuates repeatedly, ... See full document

... This manual explains the installation of the following IPTRK circuit cards, which are used to send/receive voice or FAX (G3) information via the Intranet. Although PA-8IPTB is equipped with a total of eight ports, ... See full document

... The CPU transfers line/trunk card control information to the associated peripheral circuits via IO Bus. When a parity error is detected in the transfer data or when the required information cannot be transferred from a ... See full document

... This circuit card includes the Digital Tone Generator (DTG) and hold tone (MUSIC) insertion circuit. The TONE ROM located on this circuit card contains the audible tone, and the hold tone is supplied from the EMA card. ... See full document