• No results found

[PDF] Top 20 Strength Prediction of Corbels Using Strut-and-Tie Model Analysis

Has 10000 "Strength Prediction of Corbels Using Strut-and-Tie Model Analysis" found on our website. Below are the top 20 most common "Strength Prediction of Corbels Using Strut-and-Tie Model Analysis".

Strength Prediction of Corbels Using Strut-and-Tie Model Analysis

Strength Prediction of Corbels Using Strut-and-Tie Model Analysis

... the strut-and-tie models for the design of corbels, while only for corbels having shear span-to-depth ratio greater than ...a strut-and-tie model described in ACI 318-11, ... See full document

12

The Behavior of High Strength Self-Compacting Reinforced Concrete Corbels Strengthened with NSM Steel Bars

The Behavior of High Strength Self-Compacting Reinforced Concrete Corbels Strengthened with NSM Steel Bars

... designed using Shear Friction Method for a/d up to unity and adopting Strut and Tie Model (STM) for a/d values less than two ...of corbels is to transfer heavy concentrated loads of ... See full document

7

Numerical Modelling Behaviour of Reinforced Concrete Deep Beam with Strut-and-Tie Model

Numerical Modelling Behaviour of Reinforced Concrete Deep Beam with Strut-and-Tie Model

... Abstract Strut-and-tie models (STMs), model fighters and binder are derived from the truss analogy ...and model a reinforced concrete deep beam structure for internal force distribution from ... See full document

9

Strut-and-Tie Method for Prediction of Ultimate Shear Capacity of Shear-Strengthened RC deep beams with FRP

Strut-and-Tie Method for Prediction of Ultimate Shear Capacity of Shear-Strengthened RC deep beams with FRP

... as Strut-and-tie method have proposed to analysis and design of deep ...beams. Strut- and-tie modeling is the most rational and simple method for designing nonflexural members currently ... See full document

18

Effect factors of strut strength for 
		reinforcement deep beams

Effect factors of strut strength for reinforcement deep beams

... The strut efficiency factor ( š¯›½ š¯‘  ) is an important for the strength of concrete for the analysis and design of reinforced deep beams based on the strut and tie ...for strut ... See full document

14

Shear Behavior of RC Deep Beam Strengthened by V-Shaped External Rods

Shear Behavior of RC Deep Beam Strengthened by V-Shaped External Rods

... beam using a transverse external post-tension rod and observed enhancements in the load carrying capacities of all the strengthened ...direction using top and bottom steel plates and post-tensioned by ... See full document

19

Topology optimization of strut-and-tie models in reinforced concrete structures using an evolutionary procedure

Topology optimization of strut-and-tie models in reinforced concrete structures using an evolutionary procedure

... tensile strength of concrete; rather, it is due to the breakdown of the load transfer mechanism at the ...27 Strut-and-tie models are primarily used to predict the behavior of fully cracked ... See full document

11

Strut-and-Tie Modeling of Reinforced Concrete Deep Beams

Strut-and-Tie Modeling of Reinforced Concrete Deep Beams

... 524 Figure 3-Effect of concrete effectiveness factor on shear strength prediction of RC deep beams with 525 shear reinforcement by STM 526 Figure 4-Effect of concrete effectiveness facto[r] ... See full document

40

Shear strength analysis of concrete beams reinforced with GFRP bars using strut and tie model

Shear strength analysis of concrete beams reinforced with GFRP bars using strut and tie model

... shaped strut is to imagine forces dispersing as they move away from the ends of the strut as shown in ...the strut which can lead to longitudinal cracking of the ... See full document

41

II. STRUT AND TIE METHOD

II. STRUT AND TIE METHOD

... Sectional analysis as well as design procedures are not valid for these members due to the complex interaction of flexure and ...The strut-and-tie method (STM) has been widely accepted and used as a ... See full document

6

Performance-based optimization of strut-and-tie models in reinforced concrete beam-column connections

Performance-based optimization of strut-and-tie models in reinforced concrete beam-column connections

... structural model depicted in Figure 3(a) was used to simulate interior beam-column connections in the finite element ...represented using a couple forces as shown in Figure ...mesh using four-node ... See full document

6

Diabetic prediction using fuzzy back propagation and analysis

Diabetic prediction using fuzzy back propagation and analysis

... done using membership function and in normal algorithms preprocessing is done using average value in non-fuzzy algorithms that data is divided into ... See full document

5

Topology optimization of strut-and-tie models in non-flexural reinforced concrete members

Topology optimization of strut-and-tie models in non-flexural reinforced concrete members

... the strut-and-tie model shown in ...optimal strut-and-tie model is quite complicated and is difficult to find if using the traditional ...the strut-and-tie ... See full document

7

Effect of Concrete Compressive Strength on Performance of  Fibrous Reinforced Concrete Corbels

Effect of Concrete Compressive Strength on Performance of Fibrous Reinforced Concrete Corbels

... high strength concrete corbels have a vertical displace- ment less than the vertical displacement of normal strength concrete corbels; this gives an indication on large stiffness of high ... See full document

8

Comparative analysis of strut-and-tie models through locally weighted regressions applied over the stress fields

Comparative analysis of strut-and-tie models through locally weighted regressions applied over the stress fields

... The strut generation algorithm produces branches that start at the coordinates of concentrated loads and compressive stress concentrations, and diffuses throughout the ... See full document

10

Comparative Analysis of Square Shape RC Frame by Replacing Masonry from Strut using Response Spectrum Analysis

Comparative Analysis of Square Shape RC Frame by Replacing Masonry from Strut using Response Spectrum Analysis

... Reinforced concrete frame structures strut mainly used in commercial and industrial purpose. This infillā€™s constructed masonry or concrete blocks. This structure can be consisting of in between columns and beams. ... See full document

5

Experimental Testing of Reinforced Concrete Deep Beams Designed by Strut-and-Tie Method

Experimental Testing of Reinforced Concrete Deep Beams Designed by Strut-and-Tie Method

... the tie, along the lower edge of the support, of the Strut-and-Tie model for design, determined in the program "ST method", is 33 ... See full document

22

Spatial Prediction of Landslides using Time Series Analysis and Support Vector Machine

Spatial Prediction of Landslides using Time Series Analysis and Support Vector Machine

... Series Analysis is used to find the direction and periodic propagation of landslides and the total amount of their ...The prediction and validation results reveal that the proposed model can help in ... See full document

6

Design and Analysis of Connecting Tie Rod Assembly for Automotive Application | Journal of Engineering Sciences

Design and Analysis of Connecting Tie Rod Assembly for Automotive Application | Journal of Engineering Sciences

... design model has mod- ified toclamp groove design with EN8 carbon steel mate- ...static analysis results shows deformation of the proposed tie rod model is lower than existing tie rod, ... See full document

6

VIBRATION ANALYSIS OF TIE-ROD/TIE-BOLT ROTORS USING FEM

VIBRATION ANALYSIS OF TIE-ROD/TIE-BOLT ROTORS USING FEM

... The model of turbine would not be completed before taking into account the effect of bearings. In our case, turbine is mounted on journal bearings. So, these journal bearings have been modeled as equivalent ... See full document

9

Show all 10000 documents...