[PDF] Top 20 Thermal damage detection and characterization in porous materials

... Based on the encouraging results in [5] which verified that a homogenization approach provides good approximations to solutions u rand for problems on porous domains, we will use a model motivated by ... See full document

... for characterization of the architecture, particularly the distributions of orientation and of length (aspect ratio) of fibre ...of thermal and mechanical properties can be adapted to incorporate such ... See full document

... and thermal characteristics have been determined ...the characterization of porous materials presenting important porosity (> 95%) with very large ...building materials like ... See full document

... Tuller 2009, Segmentation of X-ray computed tomography images of porous materials: A crucial step for characterization and quantitative analysis of pore structures, Water Resources Resea[r] ... See full document

... etc.) provide the confined surfaces for the nucleation and growth of inorganic salts or the polymerization of organic monomers, which finally form a stable coating (shell) around the initial templates. A subsequent ... See full document

... real time analysis of the product gases evolved during a thermally induced reaction will greatly enhance the possibility of correctly interpreting the kinetic data and arriving at most appropriate mechanism gover ning ... See full document

... For many years, the estimation of water content of soil by microwave remote sensing has been widely reported in the literature [1–3]. Ground Penetrating Radar (GPR) [4, 5] and Time Domain Reflectometry (TDR) [6] are the ... See full document

... that damage such as cracks, corrosions, and de- laminations in a structure produces changes in mass, stiness, damping and other characteristics and material parameters in dynamic response models for the ...the ... See full document

... the damage due to oxidation grows, it takes longer for the system to reach thermal ...the damage is from the source boundary, the closer together the source and back boundary temperatures are for ... See full document

... a thermal conductivity measurement ...the thermal domain and the property of ...sensor. Thermal flow sensors are a well established concept, with the most common design using one heating ele- ment ... See full document

... blocking materials are re- ...These materials have the chemical functionality to transport electrons and were used as the electron transport/hole blocking layer in blue elec- trophosphorescent OLED ...two ... See full document

... A effort to develop thin-film SMA material models is warranted to ensure the existence of appropriate modeling and simulation tools needed to support design, performance evaluation, and quantification of material ... See full document

... Carboxylate ligands can yield multidimensional neutral frameworks due to their rich coordination chemistry, eliminating the need for counterions that can sit in the cavities of frameworks and block potential porosity. ... See full document

... Chae, B., Kim, Y.H., Jung, Y.M., Han, D.H., Kim, S.B., and Lee, S.W. (2009). Spectroscopic and Thermal Degradation Studies of Polystyrene Grafting Onto Poly(Tetrafluoroethylene-Co-Hexafluoropropylene) Films Via ... See full document

... The basic methodology was the same as was used for the polarimetric sensor, but in this case the directional sensitivity of the Bragg gratings was used to determine the location of the hole. Two rosettes of Bragg ... See full document

... Moreover, tools to simplify and promote data discovery, data reuse, and development of advanced materials informatics, is critical to transforming a research-to-market adoption pipeline [7]. Digital data can be ... See full document

... impact damage indicate that probably little mode conversion occurred as has been observed from the FE ...impact damage in Plate ...impact damage can be estimated to be about 10 mm × 25 ...impact ... See full document

... According to the results obtained in this part of the study, workpiece properties, especially the type of fibres, and the orientation of the reinforcement respect to the machining direction showed significant impact on ... See full document

... and porous structure of ...the porous structures, more pores lead to the release media penetrating fully, and thus more drugs could dissolve from the ... See full document

... Table III presents a comparison between local and global minimization algorithms to estimate the thermal diffusivity and the adiabatic limit temperature of the two types of unfired clay bricks. It can be readily ... See full document