Access codes are used by the system to direct calls to the correct lines and destinations. If the codes conflict, some of the features on the system will not work. The table of default settings can help you plan your access codes so there are no conflicts. It assumes you are using a fully expanded
Tip -
If a CAP module is attached to a M7324 telephone that has not been programmed as a CAP, you will not be able to move line buttons onto the CAP module. The CAP will still be associated with the M7324 and have some default programming.If a CAP module is relocated with the M7324 telephone, the settings are retained.
You can reset a CAP module by simultaneously pressing the two buttons on the bottom left-hand side and the two buttons on the bottom right-hand side. This must be done immediately after the module has been plugged in. Performing Startup will not erase CAP programming.
176 / System prgming
Compact ICS 4.0 Installer Guide P0881600 Issue 02
Compact ICS. See the wiring information in the Installation chapter for DN numbering for smaller configurations.
Digits assigned by default to programming settings
Line pool codes
Installer password requiredThis setting allows you to assign a line pool access code for each of the three line pools (A to C). These codes are used to specify the line pool you wish to use for making an outgoing external call. Use ≠, CHANGE, the dialpad, and OK to program the access code. The default access code is
None.
Digit Use Heading
0 direct-dial digit Access codes 1 Park prefix Access codes 2, 3, 4 the first digit of B1 DNs Startup 4 and 5 the first digit of B2 DNs Startup 7 the first digit of ISDN DNs Startup 8 the first digit of DNs used with the CTA 500dm Startup 9 external line access code Access codes — — line pool access code
(Not assigned by default, but takes precedence over the External Line access code if there is a conflict.)
Access codes
— — destination code Services
Tip -
The code can be one to four digits in length. Line pool access codes starting with the same digit must be the same length.A line pool access code can be the same as an external line access code. In this case, the line pool access code takes priority over the external line access code, and a line from the line pool is selected.
A line pool access code cannot conflict with: the Park prefix, the direct-dial digit; the first digit of any Received number; the first digit of any DN (including the Auto DN or the DISA DN).
System prgming / 177
Park prefix
Installer password requiredThe Park prefix is the first digit of the call park retrieval code that must be entered to retrieve a parked call. If the Park prefix is set to None, calls cannot be parked. Press CHANGE to select the setting: 1 to 9, None, or 0.
External code
Installer password requiredExternal code allows you to assign the external line access code. This code is used to allow M7100 telephones and Analog Terminal Adapters (ATA) to access external lines.
Use CHANGE to select the setting: 1 to 9, None, or 0.
Tip -
The Park prefix cannot be the same as the direct-dial digit, the external line access code, the first digit of a DN, the first digit of a line pool access code, or the first digit of a destination code.Other programmable settings may affect which numbers appear on the display during programming. Although the numbers 0 to 9 are valid Park prefix settings, some may have been already assigned elsewhere by default or by
programming changes.
If DN length is changed, and the changed DNs conflict with the Park prefix, the setting changes to None.
Tip -
The external line access code cannot conflict with the Park prefix, the direct-dial digit, the first digit of a line pool access code, the first digit of a DN, or the first digit of a destination code.If DN length is changed, and the changed DNs conflict with the external line access code, the setting changes to None.
178 / System prgming
Compact ICS 4.0 Installer Guide P0881600 Issue 02
Direct-dial #
Installer password requiredDirect-dial digit allows you to dial a single, system-wide digit that can be used to call a specific telephone, called a direct-dial telephone. Press
CHANGE to select the setting: 1to 9, None, or 0.
Auto DN
Installer password requiredFor calls answered without DISA, no password is required to access the Norstar system. The Class of Service (COS) that applies to the call is determined by the COS for the trunk on which the user is calling. Use
CHANGE and the dialpad to enter the digits to be received from the auto-answer trunk.
Press CLRto set the Auto DN back to None.
Tip -
Another direct-dial telephone, an extra-dial telephone, can be assigned for each schedule in Services programming.The direct-dial digit cannot be the same as the first digit of a DN, of a line pool access code, the external line access code or the Call Park prefix. It cannot be the first digit of a destination code.
If DN length is changed, and the changed DNs conflict with the direct-dial digit, the setting changes to None.
System prgming / 179
DISA DN
Installer password requiredFor calls answered with DISA, the system presents a stuttered dial tone to prompt a caller to enter a valid password. The Class of Service (COS) that applies to the call is determined by this COS password.
Once a remote user is on the Norstar system, the DISA DN can be used to change the existing Class of Service. This gives you greater flexibility when you create access privileges. For example, you may want to have a shared DN for remote access and separate COS passwords with different dialing out privileges for individuals.
Use CHANGE and the dialpad to enter the digits to be received from the auto-answer trunk. Press CLR to set the DISA DN to None.
Tip -
The length of the Auto DN is the same as the Rec'd # length specified in System prgming. The Auto DN is cleared if the Received number length is changed.The Auto DN cannot be the same as a line pool access code or a destination code.
The Auto DN can give remote access to callers using the Auto Attendant. To make features available to callers who enter the Auto DN, lines answered by Auto Attendant must be configured with a remote access package.
Tip -
The length of the DISA DN is the same as the Rec'd # length specified in System prgming. The DISA DN is cleared if the Received number length is changed.The DISA DN cannot be the same as a line pool access code or a destination code.
180 / System prgming
Compact ICS 4.0 Installer Guide P0881600 Issue 02