of 1 AIRFRAME LAB PROJECTS GRADE RECORD (Form SAT 009)

1. The AIRFRAME LAB PROJECTS GRADE RECORD (Form SAT 009) is the official school student record of the completion date and grade for each required Airframe Curriculum Lab Project. The passing requirement for each Lab Project will be 80%.

Anything less than an 80% will be considered a failing grade and will be required to be made up by the student in order to receive a final course grade.

2. The AIRFRAME LAB PROJECTS GRADE RECORD will be filled out as follows:

2.1. Enter the Students’ name, Instructors’ name and class dates.

2.2. In the Date Completed column the Instructor will enter the date that the completed project was turned into the Instructor.

2.3. In the Project Grade column the instructor will enter the final grade for the project.

2.4. If a project in the Project Title column is not

required than the Instructor will enter a “N/A” in the Date Completed column and sign his name in the Project Grade column.

2.5. If a new temporary project is added to the current class requirement by the Instructor the title of this project will be written in by the Instructor in the appropriate empty line on the Project Title column.

2.5.1. A new permanent requirement for this project will have to be initiated by a change to this form and submission to the FAA for approval.

2.6. Any final Project Grade that is below the required 80%

passing grade will be transferred to the STUDENT REQUIRED MAKE-UP TIME, Form SAT 008. This form will track the completion of the open/incomplete

requirement.

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 1 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE CH 1 – Wood Structures

CH 2 – Fabric Covering CH 3 – Aircraft Finishes

3-1-1 Identify Paint Finish Defects 3-2-1 Prepare and Apply Finishing

Materials

3-2-2 Prepare and Apply Numbers and Letters

CH 4 – Sheet Metal and Nonmetallic Structures

4-3-1 Rivet pattern layout, raised head rivets

4-3-2 Rivet pattern layout, countersink rivets

4-4-1 Programmed Instruction – Aircraft Rivets

4-4-2 Programmed Instruction – Special Structural Fasteners

4-5-1 Aluminum form design and fabrication

4-5-2 Programmed Instruction – Bend allowance

4-5-3 Bend allowance and parts fabrication

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 2 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE 4-5-4 Fabricate an a/c rib with

lightening holes

4-5-5 Fabricate an a/c spar section 4-5-6 Shrinking and stretching aluminum

angles

4-5-7 Forming convex and concave flanges 4-5-8 Manufacture joggle tool and joggle

material

4-5-9 Manufacture a rivet gauge 4-5-10 Joggle a piece of material 4-5-11 Flush patch on fuselage

4-5-12 Patch repair of circular hole on fuselage

4-5-13 Channel flange repair

4-5-14 Programmed Instruction – Heat treatment of aluminum alloys 4-5-15 Web repair of aircraft spar

assembly

4-5-16 Manufacture a honeycomb fiberglass panel

4-5-17 Identify damage, develop repair and repair fiberglass panel

CH 5 - Welding

5-1-1 Programmed Instruction – Soldering methods

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 3 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE

CH 6 – Assembly and Rigging

6A-1-1 Rigging and Assembly Data 6A-2-1 Control Surface Balance,

Installation and Rigging

6A-3-1 Control Surface Travel Measurement 6A-4-1 Aircraft Jacking – Cessna 310

6B-1-1 Rotary Wing Rigging Requirements CH 7 – Aircraft Landing Gear

Systems

7-1-1 Hydraulic Landing Gear System Operation

7-1-2 Cessna 310 Main Landing Gear Strut Removal/Installation and Overhaul 7-1-3 Cessna 310 Nose Landing Gear Strut

Removal/Installation and Overhaul

7-1-4 Cessna 310 MLG Brake Assembly Removal/Installation and Overhaul 7-1-5 Cessna 310 Nose Gear Shimmy

Dampener Removal/Installation and Overhaul

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 4 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE CH 8 – Hydraulic and

Pneumatic Power Systems

8-1-1 Fabricate and install a Fluid Line in an Operational Hydraulic System 8-1-2 Select and Install Seals in an

Operational Hydraulic System Component

8-1-3 Selection of Hydraulic Fluids 8-1-4 Remove, Clean, Inspect and

Reinstall the Hydraulic Filter 8-1-5 Check the Pneumatic Charge and

Service the Accumulator

CH 9 – Cabin Atmosphere Control Systems

9-6-1 Check the Components of an Oxygen System for Serviceability

CH 10 – Aircraft Instrument Systems

10-1-1 Remove, Install & Troubleshoot Aircraft Pressure and Electrical Instruments

10-1-2 Testing Static Pressure System 10-1-3 Testing Pitot Pressure Lines

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 5 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE CH 11 – Communication and

Navigation Systems

11-1-1 Install BNC Connector on Antenna Coaxial Cable

11-2-1 Inspect, Check and Troubleshoot a Basic IFR Aircraft Package

CH 12 – Aircraft Fuel Systems

12-1-1 Turbine Fuel System Operation 12-1-2 Turbine Fuel System Fault

Troubleshooting CH 13 – Aircraft Electrical

Systems

13-1-2 Use of an Aircraft Electrical Shop Manual

13-1-3 Set up and Operate the Multimeter 13-1-4 Troubleshoot 28 Volt Electrical

System CH 14 – Position and Warning

Systems

14-1-1 Identify and Check the Functions of the Landing Gear Position

Indication System

14-1-2 Identify and Troubleshoot Landing Gear Position Indication Systems

SCLA SCHOOL OF AVIATION TECHNOLOGY AIRFRAME LAB PROJECTS GRADE RECORD

STUDENT NAME: _________________ INSTRUCTOR: ________________ CLASS DATES: ____________

AIRFRAME LAB PROJECTS

Form SAT 009 Page 6 of 6

CURRICULUM SECTION IDENT PROJECT TITLE DATE

COMPLETED

PROJECT GRADE CH 15 – Ice and Rain Control

Systems

CH 16 – Fire Protection Systems

16-1-1 Engine Fire Protection System Inspection and Maintenance

CH 17 – Airframe Inspection

17-1-1 B727 Conformity Inspection

I CERTIFY THAT ALL THE FINAL GRADES LISTED ON THIS AIRFRAME LAB PROJECTS GRADE RECORD ARE TRUE AND CORRECT.

INSTRUCTOR: _______________________________ DATE: __________

SCLA SCHOOL OF AVIATION TECHNOLOGY OPERATION MANUAL

________________________________________________________________

Chapter: 5 Section: 11 Date Issued November 10, 2009

Revision: 1

Page 1 of 1